Question about 1997 Dodge Intrepid

1 Answer

OBD2 DTC P0700 &P0733

I have a1997 dodge intrepid . The DTC is P0700 and P0733 .Has anyone received these codes and had success clearing these codes. And what did you do to solve this problem. Help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 328 Answers

P0700 Transmission Control System Malfunction P0733 Gear 3 Incorrect ratio INFO FROM http://autorepair.about.com/cs/troubleshooting/l/bl_obd_7.htm
hope this helps.....good luck!

Posted on Dec 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Generated DTC P0340. Replaced both position sensors but still have DTC P0340. Why?


Did u clear the code with obd2 scanner if not try unhooking battery for 15 min and then hook battery back up if code still comes up may have bad wire some where or faulty sensor

Apr 30, 2015 | 2001 Dodge Intrepid

1 Answer

P0700, p0733, reverse not working


have you checked fluid level and color of the fluid. the color of it should be a red in color. also a question dodges take a special fluid have you put in any other type fluid that is not specific to your car. however unfortunatley i believe the transmission needs rebuilt or the module has gone bad.

Apr 03, 2013 | 2005 Dodge Grand Caravan

1 Answer

I have a 1998 dodge Grand Caravan with codes P0700,P0734 & P0733. What does this mean?


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Jan 22, 2013 | 2003 Dodge Caravan

1 Answer

Codes p0700,p0733,p0734 dodge caravan 1997


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Apr 03, 2012 | 2003 Ford Focus

1 Answer

P0700 p0733 p0734 1997 chrysler intrepid


P0700 codes are Transmission DTC's (Diagnostic Trouble Codes)...

The specific codes are Incorrect Gear Ratio codes. This problem could be caused by low transmission fluid, deteriorated transmission fluid, a shift solenoid malfunction, the transmissions line pressure, quite a few electrical problems, etc. First step would be to check the fluid level the correct way. The vehicle must be up to operating temperature, and the shifter must be in the Neutral position. Also look at the color of the fluid. If the fluid is no longer the right condition, (most of the time it is bright red) it will be brown, or darker looking. Also smell the fluid, it may smell burnt. If this is the case, the clutch may also be slipping. In conclusion, if the fluid is NOT the problem, you may need to have the transmission tested by a certified technician. Hope this helps you.

Feb 25, 2011 | 1997 Dodge Intrepid

1 Answer

What do i need to replace to fix error code p0700 on a 2002 dodge intrepid


(DTC) CODE # P0700....Transmission Control System (MIL Request) Translation: Transmission Control Module (TCM) Malfunction or Failure. P0700 Information Code The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM. This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it.

I hope this helps....let me know if I can assist further !!

Feb 21, 2011 | 2002 Dodge Intrepid

1 Answer

P0700


P0700 means that the TCM (transmission control module) has detected a fault in the electronic control system of the transmission and has requested the PCM (powertrain control module) to turn on the check engine light to alert u to the fact that the transmission has malfunctioned, u must now get the the TCM tested to see what particular fault code(s) u have, these codes can't be read with a generic ODB2 scanner or code reader, u need a dealer to test the TCM, the OBD2 code reader can't do that.

Oct 17, 2010 | 2002 Dodge Intrepid

2 Answers

I have a 2004 Dodge Intrepid SE and the check engine light has been on for several days. I took it to Auto Zone and they plugged in their tester. They gave me the following codes - P1776 and P0700. Please...


P0700 code is a generic code for Transmission Control System Malfunction


P1776 code means your solenoid switch valve is stuck in low reverse. (DTC 47) A stuck solenoid switch valve is a common occurrence in the valve body of the Dodge 41te transmission.

The first step would be to check the wiring to the solenoid from the TCM, then maybe try a new solenoid pack if the wiring is determined to be fine.

Jan 06, 2010 | 2004 Dodge Intrepid

1 Answer

2002 Dodge Caravan, Tranny would shift, DTC P0700, P0725


replace the input speed sensor to transmission and the wiring pigtail all are available at your chrysler dealer take your vehicle registration in to the parts counter so they have your vin # to get the right part and it is the front of trans by fluid linres to radiator.

Mar 08, 2009 | 2002 Dodge Caravan

Not finding what you are looking for?
1997 Dodge Intrepid Logo

2,204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...