Question about 2007 Suzuki Reno Hatchback

1 Answer

Wont start i did a code read and got 3 codes. p2106 p2110 p2101 what are these and am i able to fix them (how) or do i need to take to a professional

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 149 Answers

The sensor ($100) in the throttle body ($400) is dirty and your engine is running high mix of gas. If you do not get it fixed, it will melt your catalytic converter ($1000) and stop up your muffler and your car will not run until you clean out the muffler system. If your car is not running, test this by disconnecting the exhaust manifold and try to start it.

Posted on Dec 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Working on 2003 Lincoln LS 3.0. code p2110; p2107. Customer replaced throttle body


P2110 - Throttle Actuator Control System - Forced Limited RPM. Throttle actuator control system is in FMEM mode of forced limited RPM.
  • PCM damaged
  • Cross wired TACM motor
DTC indicates only that FMEM condition exists, and can be set incombination with DTCS P2100, P2101, or P2107, meaning the ETB faults should be repaired first.
P2107 - Throttle Actuator Control Motor Processor. The ETC control area of the PCM failed self test. Fault could be the result of an incorrect TP command, or the TACM wires shorted together.
  • TACM wire shorted together
  • TACM circuit wires shorted to pwr
  • PCM damaged
  • ETB damaged
An (TACM) circuit PID reading may indicate a fault if available
DV21 CHECK ETC MOTOR FOR SHORT OR OPEN
  • Remove ETC motor harness connector.
  • Measure the resistance between the TACM + and TACM - pins, through the motor.
Is the resistance less than .8 ohms, or greater than 1000 ohms?
Yes No Replace Throttle body assembly. note: Clear DTCS and rerun self test, if DTCS (P2100, P2106, P2112), or (P2100, P2106, P2111, P2112) are output GO to DV22 , for (P2100, P2106, P2107) GO to DV23 , and for (P2100, P2106, P2107, P2111, P2112) GO to DV24 , and for DTCS (P2101, P2106, P2110, P2111, P2112) GO to DV25 . GO to DV22 . DV22 CHECK ETC MOTOR HARNESS FOR OPEN
  • Remove PCM harness connector.
  • Measure the resistance of the TACM+ circuit between the PCM and TACM harness connectors.
  • Measure the resistance of the TACM- circuit between the PCM and TACM harness connectors.
Is the resistance less than 5 ohms?
Yes No GO to DV23 . Repair open circuit. DV23 CHECK ETC MOTOR HARNESS FOR SHORT TO GND, PWR, ETCREF, AND ETCRTN
  • Measure the resistance between the TACM + pin and battery gnd.
  • Measure the resistance between the TACM - pin and battery gnd.
  • Measure the resistance between the TACM + pin and battery pwr.
  • Measure the resistance between the TACM - pin and battery pwr.
  • Measure the resistance between the TACM + pin and ETCRTN.
  • Measure the resistance between the TACM - pin and ETCRTN.
  • Measure the resistance between the TACM + pin and ETCREF.
  • Measure the resistance between the TACM - pin and ETCREF.
Are both resistances greater than 10K ohms?
Yes No GO to DV24 , for P2101, GO to DV25 . Isolate and repair short circuit. DV24 CHECK ETC MOTOR HARNESS FOR CIRCUITS SHORTED TOGETHER
  • Measure the resistance between the TACM + pin and TACM- pin.
Is the resistance greater than 10K ohms?
Yes No GO to DV25 . Isolate and repair short circuit. DV25 CHECK FOR CROSSWIRED ETC MOTOR HARNESS
  • Measure the resistance between the TACM + pin and TACM- pin.
Is the resistance greater than 10K ohms?
Yes No GO to DV26 . Properly wire the TACM per TACM and PCM connector diagrams. DV26 SELF TEST VEHICLE
  • Key On Engine Off.
  • Clear DTCS.
  • Cycle accelerator pedal to the floor and back several times.
  • Self Test vehicle noting any DTCS.
Were there any DTCS related to the ETC system?
Yes No Intermittent fault, GO to Z1 Replace PCM.

Oct 13, 2017 | Lincoln Cars & Trucks

1 Answer

How do i fix?


P0122 throttle/pedal position sensor/switch A circuit low input
P0223 throttle/pedal position sensor/switch B circuit high input
P2101 throttle actuator ctrl motor circuit rang/perf
P2104 throttle actuator ctrl sys-forced idle
P2110 throttle actuator ctrl sys-forced limited rpm

Here is the meaning of the codes hope this helps

Sep 20, 2015 | Cars & Trucks

1 Answer

P2106 P2110 P2135 P1516


Here is what meens those codes:

P2106
Throttle Actuator Control System - Forced Limited Power

P2110
Throttle Actuator Control System - Forced Limited RPM

P2135
Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation

P1516
Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance

I beleive that there is, specifically for chevrolet aveo 2006 a technician service bulletins.

You should have it checked at gm dealer!!!

ask for
TSB Number: SB-08-06-04-004
TSB Number: 08-06-04-023

Jan 27, 2014 | 2006 Chevrolet Aveo

1 Answer

2013 chrysler 200 electronic throttle indicator comes when engine starts jerking


My car is reading codes P0121 P0221 P0223 P0123 P2135 P2101 P2110 P2111 P0562

Aug 30, 2013 | Chrysler Cars & Trucks

1 Answer

Korean chevy problem


need to diagnose the BCM for codes ,too. the car with a lock signal indicates a security system fault. that would explain the dying after 3 seconds because the ecm has turned the fuel injectors off.

Jun 11, 2012 | Chevrolet Cruze Cars & Trucks

1 Answer

This is what the code reader tells me. P161B, P0496,P2110, AND P2106 can you help me


P161B = Engine Torque Control - Limit Reached = the torque delivered by the motor has exceeded its rated value
P2106 = Throttle Actuator Control System - Forced Limited Power
and
P2110 = Throttle Actuator Control System - Forced Limited RPM = the engine overrevved , pumped more power than it was rated for and it had to be forced to slow down by closing the throttle.
All this is caused by P0496 = Evap Emmission high--- purge flow fault = the evap valve got stuck in the fully open position, pumped a lot of fuel in the motor and acted like a fully opened throttle; have it cleaned and if that doesn't fixes, replace it.

Aug 20, 2011 | 2006 Suzuki Forenza

Not finding what you are looking for?
2007 Suzuki Reno Hatchback Logo

567 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...