Question about 2001 Mazda Pickup Regular Cab

1 Answer

2001 Mazda pickup, series B: front air bag warning

When running, an image of the front air bag with driver appears on the dash panell. This image blinks on and off. The vehicle just turned 52,000 miles. I assume this is a maintenance warning and just needs to be acknowledged. How do I turn this off or must I return to the dealer to have maintenance performed?

Posted by on

  • d_marku Feb 24, 2009

    i have the same problem, i dont know if it should stay on to show that your air bags are on like an O/D light or if it is a warning light and should be off, and i don't know if turning the passenger airbag on or off with the little key would help. (i can't find my air bag key)

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 52,141 Answers

Go to the dealer as there are air bag recalls out
it could be a sensor or wiring problem

Posted on Dec 20, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: Bad catalytic converter(s) ???

let the car run for about 15 min look underneath if the cat is bad its should be glownin

Posted on Dec 16, 2008

  • 4 Answers

SOURCE: check engine light is blinking

check the spark plug wires for dry rotting and check the order there in starting from the back of the motor left to right the order go's 1..2..3 and then the front left to right the order go's 4..5..6 also make sure that all the wires are plugged in the right order on the distributor also it could be your TCS or "TRACTION CONTROL SYSTEM" 

Posted on Dec 30, 2008

MNfisherman
  • 11896 Answers

SOURCE: My 2006 Mazda Tribute makes a pulsating noise when

If you have drum brakes in back instead of disc brakes, that could be your problem. Very common noise with drums. Pads, springs, could be sticking, or pistons if it is disc brakes

Posted on Mar 31, 2009

  • 6 Answers

SOURCE: replacing front bumper of mazda mx5

It should only need little plastic pins and screws. You could get these at Auto Zone or another auto part store near you.

Posted on Mar 31, 2009

  • 74 Answers

SOURCE: My headlights on my mazda Astina 323 1990 wont pop up

check fuses

Posted on Oct 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is passenger side air bag relay 2007 MKZ


There is no relay for the passenger side air bag . What seams to be the trouble ? There is possibly a code set in the air bag control module .
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants, in addition to that provided by the 3-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles are also equipped with driver and front passenger safety belt retractor pretensioners. These vehicles can also be equipped with optional side air curtains that deploy from the A-pillar to the C-pillar upon a side impact. Vehicles with optional side air curtains are also equipped with seat side air bag modules in the front seats.
Side air curtains deploy from the headliner, protecting the first and second row outboard occupants during a side impact. Seat side air bag modules deploy from the outboard front seat backrest upon a side impact. In addition, a front impact severity sensor is mounted to the lower radiator support, a seat position sensor is mounted to the driver seat and a usage detection switch is added to the front driver and passenger outboard buckles. If equipped with optional side air curtain modules and seat side air bag modules, there are an additional 4 side impact sensors.
Vehicles are also equipped with an occupant classification sensor (OCS) system as part of the front passenger seat. The OCS system includes 2 OCS rails and an OCS module.
Passenger Air Bag Deactivation (PAD) Indicator
The passenger air bag deactivation (PAD) indicator is a visual indicator used to inform the front seat occupants of the passenger air bag deactivation state. The PAD indicator is a stand-alone lamp installed into the vehicle instrument panel in a position visible to each front seat occupant.
The restraints control module (RCM) controls the state of the PAD indicator through a direct hardwire connection, based on information provided by the occupant classification sensor (OCS) system. The PAD indicator is lit to indicate the passenger air bag module is disabled. An exemption to this is when the front passenger seat is determined to be empty and passenger safety belt buckle unbuckled, and therefore indication of a deactivated passenger air bag module is not necessary. In all other cases, the PAD indicator is unlit when the passenger air bag module is enabled.
When the ignition switch is in the ON position, the PAD indicator prove-out period is initiated by the RCM. The RCM briefly activates the PAD indicator to prove-out the indicator function and verify to the front occupants correct functional operation of the PAD indicator.
The PAD indicator will be lit/unlit within 1.0 to 1.5 seconds of a change of state from the OCS system.
When an OCS system fault is present, the RCM defaults the passenger air bag module to the last valid state received from the OCS system until the ignition switch is turned OFF. If the OCS system fault is still present when the ignition switch is turned ON, the RCM defaults the passenger air bag module to enabled regardless of the size of occupant in the front passenger seat. The PAD indicator will be unlit. For information on the OCS system, refer to Occupant Classification Sensor System in this section.
The following table indicates the passenger air bag status and the PAD indicator status based the size of the front outboard passenger occupant.

Oct 04, 2015 | 2007 Lincoln MKZ

1 Answer

Left signal lights do not work on 2005 sts


Check for power at the light socket aswell as grounds

Jun 16, 2012 | 2005 Cadillac STS

2 Answers

Steering wheel adjustment , the steering whell is 90degrees off but the car does not pull eather direction. car was stolen no damage just steering whell truned


jack front of car up then turn steering wheel full lock to full lock and count the number of turns from either side then divide by 2 so you have the straight ahead position then remove the steering wheel and replace in the straight ahead position ,iam saying this because the vehicle may have been re tracked and only one track rod end adjusted so you have say 2 turns to the left and 2 and half to the right if you follow me .or remove the steering wheel then just hold it on and slowly drive forewards and lift wheel and refit to the correct position

Feb 10, 2011 | 1999 Mercury Grand Marquis

1 Answer

How do i replace a heater cord?


  1. Disconnect the battery ground cable
  2. Remove the console glove compartment. Disconnect the power point electrical connector. If equipped, disconnect the cellular phone antenna cable and coaxial cable from the console glove compartment. If equipped, disconnect the cellular phone antenna cable and coaxial cable.
  3. If equipped, remove the compact disc changer. Remove the screws. Disconnect the electrical connector. Remove the digital audio compact disc player.
  4. Place the gearshift lever in the 1 position.
  5. Remove the console top panel. Disconnect the cigar lighter electrical connector.
  6. Remove the floor console to floor bracket screws.
  7. Remove the floor console to gearshift bracket screws.
  8. Remove the floor console. Slide the floor console rearward. Remove the floor console. Disconnect the three electrical connectors. CAUTION
    Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result.
  9. Remove the passenger side air bag module. WARNING
    Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment. WARNING
    Carry a live air bag module with the air bag and deployment door pointed away from your body. This will reduce the risk of injury in the event of an accidental deployment. WARNING
    Do not set a live air bag module down with the deployment door face down. This will reduce the risk of injury in the event of an accidental deployment.
  10. Disconnect the battery ground cable and wait at least one minute.
  11. Push in on the two glove compartment door tabs and position downward.
  12. Disconnect the passenger air bag module electrical connector. Remove the passenger air bag module retaining bolts.
  13. Remove the passenger air bag module. Note: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
  14. If equipped, remove the rear seat climate control air duct sleeve.
  15. Remove the steering column. CAUTION
    Do not remove the steering column, steering wheel and air bag module as an assembly from the vehicle. Unless the steering column is locked to prevent rotation; or the lower end of the steering shaft is wired to prevent the steering wheel from being rotated, damage to the air bag sliding contact will occur. NOTE: All steering column components are assembled with specific fasteners. They are designed with a thread locking system to prevent loosening due to vibrations associated with normal vehicle operation. Make sure vehicle front wheels are in the straight-ahead position
  16. Remove the ignition switch lock
  17. Remove the steering wheel.
  18. Remove the air bag sliding contact.
  19. Remove the tilt wheel handle and shank by unscrewing it from the steering column.
  20. Remove the four upper and lower steering column shroud retaining screws. Remove the upper steering column shroud and lower steering column shroud.
  21. Remove the lower instrument panel trim cover.
  22. Unsnap the steering column lower trim panel.
  23. Remove the release lever hood retaining screws.
  24. Remove the brake release retaining screws.
  25. Remove the instrument panel steering column opening cover reinforcement
  26. Remove the instrument panel reinforcement brace.
  27. Disconnect the shift cable and bracket from the steering column by removing two screws.
  28. Disconnect the transmission shift cable loop from the shift tube hook (column shift).
  29. Remove the two multi-function switch retaining screws and set the multi-function switch aside.
  30. Remove the retaining screw and remove the wiring connector from the ignition switch.
  31. Remove two front steering column nuts and the steering column impact absorber
  32. Remove the pinch bolt from the steering column lower yoke.
  33. While supporting the column assembly, remove two rear column assembly retaining nuts.
  34. Disconnect the shift cable and bracket from the selector lever pivot. Disconnect the shift cable from the steering column shift tube lever. Disconnect the shift cable from the steering column bracket.
  35. Remove the shift cable and bracket from the lower column mounting.
  36. Remove two shift lock actuator-retaining screws and remove the shift lock actuator (console shift only).
  37. Remove the steering column from the vehicle.
  38. Release the cable from the parking brake actuator.
  39. Release the cable conduit from the parking brake actuator.
  40. To disconnect the driver's side outboard bulkhead electrical connector. Loosen the bolt. Disconnect the driver's side bulkhead electrical connector.
  41. To disconnect the driver's side inboard bulkhead electrical connector. Loosen the bolt. Disconnect the driver's side bulkhead electrical connector.
  42. If equipped, disconnect the heated seat switch electrical connectors.
  43. Remove the steering column mounting support to instrument cowl brace bolts.
  44. Remove the instrument panel dash brace to instrument panel bolt.
  45. Loosen the nut that secures the instrument panel dash brace. Position the instrument panel dash brace aside.
  46. Remove the pin-type retainers. Remove the passenger side instrument panel insulator. Remove the courtesy lamp.
  47. Disconnect the vacuum harness connector.
  48. Disconnect the in-line electrical harness connector.
  49. Position the passenger side scuff plate aside.
  50. Remove the passenger side cowl trim panel.

Feb 06, 2011 | 1999 Lincoln Continental

1 Answer

Need to remove heater A/C dash control , what is proper procedure?


Look at fig. 4 for the heater a/c dash control: HEATER CORE Altima REMOVAL AND INSTALLATION
  1. Position the steering wheel in the straight-ahead position.
  2. Turn the ignition switch OFF.
  3. Disconnect the negative (() battery cable; then, the positive (+) battery cable. NOTE: Wait for a least 3 minutes after disconnecting the battery cables for the charge in the air bag circuit to dissipate before working on the air bag module(s).
  4. Remove the driver's side SRS and steering wheel by removing or disconnecting the following:
    • Lower lid from the steering wheel and disconnect the driver's air bag module connector
    • Left and right side lids from the steering wheel
    • Special bolts from both side of the steering wheel using a tamper resistant Torx wrench (T50)
    • Air bag module and store it face up
    • Horn's electrical connector and remove the steering wheel nut
    • Steering wheel from the steering column using a suitable puller
  5. Remove the passenger's side SRS by removing or disconnecting the following:
    • Glove box door and the glove box
    • Front passenger's air bag module connector
    • 2 special bolts using a tamper resistant Torx wrench (T50)
    • 4 passenger's air bag-to-instrument panel nuts
    • Front passenger's air bag module and store it face up.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
  8. Working in the engine compartment, disconnect the heater hoses from the heater core tubes.
  9. Remove the instrument panel by removing or disconnecting the following:
    • Kick plate and dash side finisher on the driver's side
    • 2 lower panel-to-instrument panel screws and the lower panel on the driver's side
    • 2 lower reinforcement panel-to-instrument panel screws and the lower reinforcement panel
    • 6 steering column cover screws, the covers, the spiral cable and combination switch
    • 2 cluster lid "A" screws and the cluster lid "A"
    • 3 combination meter screws, disconnect the electrical harness connector and remove the combination meter
    • Switch panel
    • Instrument panel lower covers
    • Snap out the transmission shifter finisher (boot)
    • 4 cluster lid "C" screws and the cluster lid "C"
    • 4 audio and deck pocket-to-instrument panel screws and the audio and deck pocket
    • 5 center console screws and the center console
    • 2 center instrument panel screws and the center panel
    • front defroster grilles
    • Front pillar garnish
    • Instrument panel 3 nuts/4 screws and the instrument panel
    • 8 instrument stay assembly nuts and the stay
    • Steering member assembly 5 nuts/1 bolt and the steering member
  10. Remove the air conditioning housing assembly by removing or disconnecting the following:
    • Refrigerant lines from the air conditioning housing assembly
    • Thermo control amp
    • Air conditioning housing assembly
  11. Remove or disconnect the following:
    • Heater unit
    • Heater core from the heater unit Fig. 1: Exploded view of the steering wheel and air bag module 93112gd9.gif
      Fig. 2: Exploded view of the passenger's side air bag module 93112gd0.gif
      Fig. 3: Exploded view of the instrument panel assembly 93112ge1.gif
      Fig. 4: Exploded view of the heater housing assembly and related components 93112ge2.gif
      Fig. 5: View of the heater core and heater housing 93112ge3.gif
    To install:
  12. Install or connect the following:
    • Heater core to the heater unit
    • Heater unit
  13. Install the air conditioning housing assembly by installing or connecting the following:
    • Air conditioning housing assembly
    • Thermo control amp
    • Refrigerant lines to the air conditioning housing assembly
  14. Install the instrument panel by installing or connecting the following:
    • Steering member assembly and the steering member 5 nuts/1 bolt
    • Instrument stay assembly and the 8 stay nuts
    • Instrument panel and the instrument panel 3 nuts/4 screws
    • Front pillar garnish
    • Front defroster grilles
    • Center instrument panel and the 2 center panel screws
    • Center console and the 5 center console screws
    • Audio and deck pocket and the 4 audio and deck pocket-to-instrument panel screws
    • Cluster lid "C" and the 4 cluster lid "C" screws
    • Snap in the transmission shifter finisher (boot)
    • Instrument panel lower covers
    • Switch panel
    • Combination meter, connect the electrical harness connector and install the 3 combination meter screws
    • Cluster lid "A" and the 2 cluster lid "A" screw
    • Combination switch, the spiral cable, the covers and the 6 steering column cover screws
    • Lower reinforcement panel and the 2 lower reinforcement panel-to-instrument panel screws
    • Lower panel and the 2 lower panel-to-instrument panel screws, on the driver's side
    • Kick plate and dash side finisher, on the driver's side
  15. Working in the engine compartment, connect the heater hoses to the heater core tubes.
  16. Install the passenger's side SRS by installing or connecting the following:
    • Front passenger's air bag module
    • 4 passenger's air bag-to-instrument panel nuts
    • 2 new special bolts and torque using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm)
    • Front passenger's air bag module connector
    • Glove box door and the glove box
  17. Install the driver's side SRS and steering wheel by installing or connecting the following:
    • Steering wheel to the steering column
    • Steering wheel nut and torque the nut to 22-29 ft. lbs.
    • Horn's electrical connector
    • Air bag module
    • New special bolts to both sides of the steering wheel and torque the bolts using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm).
    • Both the left and right side lids to the steering wheel
    • Lower lid to the steering wheel and connect the driver's air bag module connector
  18. Refill the cooling system.
  19. Connect the positive (+) battery cable; then, the negative (() battery cable.
  20. Evacuate, charge and leak test the air conditioning system refrigerant.
  21. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Nov 19, 2010 | 2002 Nissan Sentra

1 Answer

Air bag light blinks a code 13 continuously, It doesn't come on and stay on it blinks 1---1-1-1......1---1-1-1.....etc. I have change the two sensors in the front, checked fuses(no fuses with a direct link...


The Supplemental Air Bag Restraint System consists of two basic sub-systems:
  • Driver side air bag module (043B13) and passenger side air bag module (044A74).
  • Electrical system, including RH primary crash front air bag sensor and bracket (14B004) , LH primary crash front air bag sensor and bracket (14B005) , LH kick panel safing rear air bag sensor and bracket (14B007) and air bag diagnostic monitor (14B056) .
---------------------------------------------------------------------------------------
13 Air Bag or Primary Crash Sensor Circuit Shorted to Ground
  • Inspect air bag sliding contact wiring in steering wheel , driver side air bag module , and passenger side air bag module for damaged, chafed or pinched wires.
  • -------------------------------------------------------------------------------------

    Oct 28, 2010 | 1993 Mercury Grand Marquis

    2 Answers

    Airbag locations


    In the steering wheel and passenger side dash.Due to the age of the vehicle probably doesn't have the curtain "side" airbags.The airbags were designed primarily for head on collisions. Here is some useful information to why the may have not deployed courtesy of http://www.asashop.org/autoinc/dec2001/collision.htm
    How Air Bags Work To have a frontal (driver or passenger) air bag deploy, certain criteria must be met. One of these criteria is that the frontal impact must be within a 60-degree window, occurring within 30 degrees from the vehicle's centerline. Another key element is that the crash forces are equivalent to a head-on collision with an immovable barrier at 10-15 miles per hour. Because a typical automobile accident only lasts about 0.125 (1/8th) of a second, air bags deploy within 15 to 20ms after the initial crash impact. To create a protective cushion between the occupant and the vehicle's interior, the air bag inflates at speeds up to 200 mph within approximately 30ms after impact. This allows the occupant to contact a fully inflated bag within approximately 45 to 50ms after the initial crash impact. Approximately 100ms after impact the bag deflates.

    May 30, 2010 | 2001 Buick LeSabre

    1 Answer

    AIR BAG LIGHT BLINKING


    THAT IS A CODE 44 RIGHT FRONT PRIMARY AIR BAG SENSOR TO PRPERLY MOUNTED TO VEHICLE

    May 01, 2009 | Ford E-150 Cars & Trucks

    1 Answer

    How do you remove or replace the passenger airbag on a 99 contour , Is it a whole dash unit? What holds the drivers bag in the steering wheel? I assumed it was a tork but not sure. Where is the control...


    Please rate as fixya if this helps.
    the air bag control module is under the console.

    1. Disconnect the battery ground cable.
      1. Wait one minute.
    2. Remove the center console. For additional information, refer to Section 501-12 .
    -----------------------------------------------------------------
    1. Disconnect the battery ground cable.
    2. Wait one minute.
    3. NOTE: Contour shown, SVT similar.
      Remove the rear floor console screws.
      1. Move seat fully forward.
    1. Fully apply the parking brake.
    1. Detach the shift indicator selector bezel.
    1. Detach the shift bezel from the selector housing.
      1. Remove three bolts.
      1. Detach shift bezel from the console.
    1. NOTE: The rear floor console must be raised to disengage the front retaining clips.
      Raise and remove the rear floor console.
    1. Remove the four front floor console retaining screws.
    1. Detach the front floor console.
      1. Set the gearshift lever into position 1.
        Partially remove the front floor console.
    1. Disconnect the cigar lighter electrical connections and remove the front center console
    -----------------------------------------------------------
    1. Disconnect the air bag control module electrical connectors.
      1. Depress the locking tang.
      1. Slide the locking bar back.
      • Disconnect the connector.
    1. NOTE: The air bag control control module is grounded by the retaining bolts.
      Remove the air bag control module.
      • Remove the three bolts.
    --------------------------------------------------------------------------------------------
    driver air bag module

    1. Disconnect the battery cables.
    1. Rotate the steering wheel 90 degrees to access and remove the Torx screw. Rotate the steering wheel 180 degrees to access and remove the Torx screws.
    1. Remove the driver air bag module.
      • Disconnect the electrical connector.
      • Remove the air bag module.
    ------------------------------------------------------------------------------------------
    1. Disconnect the battery cables. For additional information, refer to Section 414-01 .
    1. Open the glove compartment, press the sides inward and lower the glove compartment to the floor.
    1. Remove the passenger air vent duct.
      1. Disconnect the duct from the heater box housing.
      1. Disconnect the duct from the instrument panel register and remove.
    29e093f.gif
    1. Disconnect the passenger air bag module electrical connector.
    1. Remove the two retaining bolts securing the rear of the passenger air bag module to the cross-vehicle beam.
    14df419.gif
    1. sxp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the passenger air bag module when removing the retaining nuts.
      Remove the two nuts from the front of the passenger air bag module.
    4a697c8.gif
    1. Remove the passenger air bag module.
      • Lower the front edge of the passenger air bag module, roll the passenger air bag module around the cross-vehicle beam lowering it into the passenger footwell.
    82a0ae0.gif

    Mar 15, 2009 | 1999 Ford Contour

    1 Answer

    Instrument Panel Codes??


    Yes, it's called a lamp fault code.

    9 is not familiar to me. Call dealer service department and ask them what code means.

    Here are codes for a 94 Aerostar. I don't have 91 Sable. Sorry.



    Air Bag Diagnostic Monitor Diagnostic Trouble Code Priority Table Diagnostic Trouble Code Component/Fault Description — No Air Bag Indicator — Inoperative Indicator Circuit or No Battery Positive Voltage to Air Bag Diagnostic Monitor — Continuous Air Bag Indicator — Air Bag Diagnostic Monitor Disconnected or Inoperative 12 Low Battery Voltage 13 Air Bag Module or RH Cowl Side Panel Air Bag Sensor Circuit Shorted to Ground 21 LH Cowl Side Panel Air Bag Sensor Not Mounted to Vehicle Properly 22 LH Cowl Side Panel Air Bag Sensor Circuit Shorted to Battery Voltage 23 LH Cowl Side Panel Air Bag Sensor Circuit Input Feed/Return Circuit Open 24 LH Cowl Side Panel Air Bag Sensor Diagnostic Circuit Open or Low Resistance in Center Air Bag or Front Air Bag 32 Driver Side Air Bag Circuit High Resistance or Open 33 Passenger Side Air Bag Circuit High Resistance or Open 34 Driver Side Air Bag Circuit Low Resistance or Shorted 35 Passenger Side Air Bag Circuit Low Resistance or Shorted 41 Center Radiator and RH Cowl Side Panel Air Bag Sensor Circuits High Resistance or Open 44 RH Cowl Side Panel Air Bag Sensor Not Mounted to Vehicle Properly 45 Center Air Bag Sensor Not Mounted to Vehicle Properly 46 Open Splice Center Air Bag Sensor Ground Monitor 51 Air Bag Diagnostic Monitor Internal Thermal Fuse Blown and Short to Ground No Longer Exists 52 Backup Power Supply Voltage Boost Fault 53 Sensor Circuits Resistance to Ground or Internal Air Bag Diagnostic Monitor Fault — Rapid Continuous Flashing of Air Bag Indicator

    Feb 25, 2009 | 1992 Mercury Sable

    Not finding what you are looking for?
    2001 Mazda Pickup Regular Cab Logo

    Related Topics:

    48 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    Marvin
    Marvin

    Level 3 Expert

    81400 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8841 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...