Question about 1996 Chrysler Cirrus

1 Answer

Crank sensor location on 2000 Cirrus with 2.5 motor

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 25 Answers

Hi ronco your crank shaft sensor should belocated in the front of ur motor on the crank pulley or it may be part of the damper pulley or behind it but it will be hard to see,... you will need to get under the car to c it but it will be right in that area torwards the bottom

Posted on Dec 24, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Show me a picture of the water pump on a 2000 Chrysler Cirrus LXI

The pump is part of the timing components. You only want to do this one time. So replace all the timing components. You don't have to replace the crank or cam gears.

Apr 05, 2016 | Chrysler Cars & Trucks

1 Answer

How do I replace the distributor on a 2000 cirrus, 2.5L?

you can do that as the problem is moisture inside the cap
you can seal the lot with silicon spray as well

Mar 04, 2018 | 2000 Chrysler Cirrus

3 Answers

My cirrus dies after driving about 5 miles and then dies. If I wait 5-15 minutes I can restart it and go a short distance 1- 2 miles and then repeats Thanks Jim repair center replaced crank sensor and no...

change the fuel filter.The engine is running out of fuel & possibly the fuel line is experiencing vapor lock due to insufficent gas.Hope this helps you & good luck!

Aug 19, 2010 | 2000 Chrysler Cirrus

1 Answer

Need to know where crank sensor is located.

Hello. The crank shaft sensor is located in the front of the motor on the crank pulley or it may be part of the damper pulley. It is hard to see,... you will need to get under the car to see it but it will be right in that area near the bottom of the engine.

Feb 03, 2010 | 1998 Chrysler Cirrus

1 Answer

Need location of crankshaft position sensor on a 1996 chrysler cirrus v6 location on engine and how to find it

The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Sep 28, 2009 | 1996 Chrysler Cirrus

1 Answer

2000 chrysler cirrus wont shift

it is going into limp mode. You need to take it to a trans shop to have diagnostic

Jul 06, 2009 | 2000 Chrysler Cirrus

1 Answer

How to change speed sensor for cirrus 2000

There should be 2 on the drivers side of the transmission. An input speed sensor 4800878 $21.95 and an output speed sensor 4800879 $21.95. These are easy to replace. First locate the 2 which should have a wiring harness attached to them, Second unhook the wires, Third unscrew them out individually as to not get them confused because they are different in shape just barely. Fourth screw in the new ones,Fifth replace the wires and you should be done.

Jan 13, 2009 | 2000 Chrysler Cirrus

Not finding what you are looking for?
1996 Chrysler Cirrus Logo

602 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

83850 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides