Question about 1999 Mercury Villager

1 Answer

1999 Mercury Villager Windshield Wipers will not turn off.

The wipers will not turn off or go back to delay mode. Once turned on, they do their own thing. How do I get the turn signal arm off?

Posted by on

  • chasmojo Dec 29, 2008

    Thank You.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

You have to pull the steering wheel and there are three torx screws holding the arm on

Posted on Dec 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my wiper delay module part#s5665 located for a 1998 ford Taurus?


I am not sure where you got that number. It does not cross reference to any known Ford part. The wiper delay is controlled by the module that is in the steering column. The whole thing is one piece, Turn signals wiper etc.

Sep 18, 2014 | 1998 Ford Taurus

1 Answer

2005 chev impala wipers ( in delay mode ) are in up position .. when turned off they park fine ... what could be causing this ?


The wiper motor is what holds the module. So to fix it, you have to replace the motor. Remove the wiper arms. Remove the cover, there may be a few screws to take out. Pry the control arm of the motor. Remove the bolts holding the motor. Then put the new on in.

Aug 13, 2014 | 2005 Chevrolet Impala

2 Answers

Wipers only work sometimes


check that you do not have the wiper control set on delay . It is the first stop on the arm and on some cars it is adjustable by turning the knob on the lever to give different delays according to the rain conditions. The next stop down will be continuous wipes at low speed and the last stop will be flat out speed of the wipers.

Dec 23, 2013 | Cars & Trucks

1 Answer

98 monte carlo z34 sometimes wipers won't shut off. is this the turn signal lever or the wiper delay board?


Could be either one.
The wiper switch could be providing power, and there is a park switch in the motor that provides power until the wiper arms "park".
You may be able to disconnect the wiper switch to find out.
Chances are you'll need a wiring diagram to test the circuits.

Apr 11, 2013 | Cars & Trucks

1 Answer

Just bought a used 1990 keep wrangler. The turn signal k arm on the steer wheel is missing. Is the windshield wiper control on the turn signal arm as well? I do not see a place to turn on the wipers


just get one from a junk yard to remove it just push turn and pull the only thing is that if the car has cruise control you got to cut the wire... and to install it your car push in and turn wiper will work signals but no cruise control unless you go trough steering coloum

May 01, 2012 | 1990 Jeep Wrangler

2 Answers

Windshield shutters while in delayed mode, it


Excessive grease in wiper motor. Motor needs to be removed and the grease cleaned out. Regrease only the areas needing to be greased.

There is also a recall for this vehicle for the wiper module. Call the dealer with your vin # to see if it has been done. I will post the instructions for motor removal and install.

1. Turn the key to the OFF position.
2. Open the hood.
3. Remove the three push-in retainers that attach the air inlet grille (leaf screen) to the plenum sheet metal.
4 . Lower the hood to the secondary latch.
5. Using a suitable marker or masking tape, mark the location on both wiper blades on the windshield.
6. Remove the covers from the nuts that attach the wiper arms.
7. Remove the nuts from the wiper arms.
Important
If the rocking action in the next step fails to loosen the wiper arm, it may be necessary to use a standard top-post battery cable terminal puller to remove the wiper arm.
8. Rock the wiper arms back and forth to loosen and remove them from the wiper transmission shaft.
9. Remove the antenna mast.
10. Remove the 10 mm hex head nut that attaches the left and right ends of the air inlet grille to the plenum sheet metal.
11. Remove the air inlet grille and reposition it up to the windshield. It is not necessary to disconnect the washer hose.
12. Remove the two 10 mm hex head bolts that attach the wiper module to the plenum sheet metal.
13. Disconnect the electrical connector.
14. Position the new wiper module to the vehicle and connect the electrical connector.
15. Install the wiper module in the plenum sheet metal.
16. Install the two 10 mm hex head bolts that attach the module to the plenum sheet metal. Tighten nuts to 30 N·m (22 lb ft).
17.Turn the ignition switch to the ON position, turn the wiper switch ON, and visually verify that the wiper transmissions operate. After visually verifying operation, turn the wiper switch to the OFF position and allow the wiper transmissions to stop moving before turning the ignition switch to the OFF position. The wiper motor will now be in the PARK position.
18. Using the marks or masking tape that were placed on the windshield, align and position the wiper arms on the wiper transmission shafts.
19. Install the nuts on the wiper transmission shafts. Tighten the nuts to 30 N·m (22 lb ft).
20. Install the covers on the wiper arm nuts.
21. Remove the marks or masking tape from the windshield.
22. Open the hood.
23. Install the three push-in retainers that attach the air inlet grille to the plenum sheet metal.
24. Close the hood.
25. Verify that all functions of the wiper system (low, high, delay, etc.) operate properly.

Apr 02, 2010 | 2002 Chevrolet TrailBlazer

2 Answers

Windshield wipers will not turn off, I've replace the turn signal/wiper switch and still not turning off


Sounds like the PARK SWITCH within the WIPER MOTOR is at fault, Only way to beat it is relay the motor. Hope this helps

May 08, 2009 | Cadillac DeVille Cars & Trucks

1 Answer

Problems with tun signal/wiper arm on 2004 chevy venture mini-van


I had the same thing - it also affects the 4 way flashers.  you'll end up replacing the entire control arm (turn signal lever)
Good luck!

Feb 13, 2009 | 2004 Chevrolet Venture Passanger

Not finding what you are looking for?
1999 Mercury Villager Logo

Related Topics:

396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...