Question about 2007 Isuzu Axiom

1 Answer

Need to replace rear brake light bulb

How do I get the rear light off to replace teh stop light bulb? I removed to screws - but it will not come off.

Posted by on

  • Anonymous Jan 03, 2009

    I have the same problem. It seems like it wants to pop off but Im afraid I will break something and have to replace the whole assembly. The screws came off easy but the light fixture still is in place and won't pull out.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I experienced the same problem! After removal of the two screws, apply pushing pressure from the inside out with one hand on the outside of the lens for stability. The lens should push straight out.. There are 2 straight pins that are inserted into a plastic retainer that holds the assembly in place. Good luck
averyj@hotmail.com

Posted on Jul 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change brake light bulb on a 2014 fiat 500L


https://www.fiatusa.com/download/pdf/manuals/2014-FIAT-500L-OM-1st.pdf

it's in your owners manual page 358 chapter 7

you need a torx 20 screwdriver or bit

Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp assembly.
3. Remove the four screws (using a T20 driver) and separate the backplate from the lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.

Center High-Mounted Stop Lamp (CHMSL)
This light is an LED assembly. See your authorized stealership

Mar 30, 2015 | Fiat Cars & Trucks

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

Rear turn signal b ulb burned out - How to replace


Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif

Dec 19, 2010 | 1994 Buick Century

2 Answers

2005 lincoln Ls left rear brake light bulb needs replaced. took 2 screws off but metal enclosure is tight and siliconed on. what do i do?


Lamp Assembly -Stoplamp Removal and Installation
  1. Remove the luggage compartment scuff plate.
    • Pull to unsnap.
  1. Position the luggage compartment side trim panel aside.
    1. Remove the pin-type retainers.
    1. Position the luggage compartment side trim panel aside.
  1. Remove the stoplamp assembly.
    1. Disconnect the electrical connector.
    1. Remove the three nuts.
    1. Push the rubber grommet through the sheet metal and remove the stoplamp assembly.
    • If necessary, install new bulbs.

Nov 15, 2010 | 2005 Lincoln LS

2 Answers

I can not figure out how to get into the rear light bulbs (Stop light, etc). The manual says to remove two (phillips) screws to disengage the housing from the body. There's even a a picture. However, on...


To access the rear lights, you access them from inside the trunk. Pull down the carpet at rear of trunk near latch. There should be the screws the manual is referring to. Once you locate and remove all screws, gently pull the light assembly away from body. Replace the needed bulbs then gently push assembly against the body, replace the screws and set carpet back in place.

Nov 14, 2010 | 1995 Toyota Camry

2 Answers

Audi A4 need to replace rear brake light on audi a4


Inside the boot is a plastic cap embeded in the boot liner. Remove the cap to reveal a screw. Undo the screw and the whole rear light cluster will come away in a sideways and not rearward direction to reveal all of the bulbs. Hope this helps.

Jun 04, 2009 | 2003 Audi A4 Cabriolet

1 Answer

How to change my rear brake light bulb


Okay you need to lift your trunk remove any carpeting remove hidden screws to undo light fixture be careful not to drop the case once case is in your hand remove the appropriate bulb that needs replacing after wards reinstall light housing/casing and screws good luck with this. Please Rate Me. And for further assistance you can always ask me.

Apr 25, 2009 | Toyota Avalon Cars & Trucks

1 Answer

Stop light out


For the brake light open the rear hatch and check beside the tail light. I believe ther is 2 phillips head screws right where the light meets the rear hatch on the body panel. remove them and gently yet firmly pull the lens assembly from the corner of the rear body panel. Squeeze the clips on the back of the socket and twist to remove the socket from the lens. Push gently on the bulb and turn carefully to remove light from the socket replace the light and reverse removal procedure to install.

Nov 02, 2008 | 2003 Ford Explorer

2 Answers

PT Cruiser Brake Light


The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!

Jul 14, 2008 | 2006 Chrysler PT Cruiser

4 Answers

Tail light installation


1. Use a "star" screwdriver to unscrew the two black screws on the outside.
On the inside if there is a canvas remove this by gently unscrewing the two black plastic screws

2. Use a No. 8 spanner to remove the nut on the inside.

3. Pull gently the whole casing containing all the rear lights(brake/turn
signal/reverse/blinkers)

4. Since you already oend the casing, you might as well make sure the rest ofthe bulbs are good.

5. Determine which bulb needs replacement by switching your lights on and have someone step on the brakes for you.( with the ignition turned on)

6. Remember not to lose the screws Replace everything as it was

Jun 01, 2008 | 1996 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

612 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...