I need the head bolt torque sequence for a 1996 honda accord 2.2? I also need to know the pounds of pressure and how many passes needed to torque. Thanks

https://www.google.com/search?source=univ&tbm=isch&q=ft.+pounds+for+1993+honda+accord+2.2+crank+cap+bearing&hl=en&sa=X&ved=2ahUKEwjK5tT8xLHpAhWHTcAKHeGvD_YQsAR6BAgFEAE&biw=1326&bih=627

Main Bearing Torque Sequence

1. Hand tighten bolts 1D, 1G and 1F until the bedplate contacts the block.
2. Tighten bolts 1A-1J to 40 ft. lbs. (54 Nm).
3. Tighten bolts 1- 8 to 62 inch lbs. (7 Nm).
4. Turn bolts 1-8 an additional 90°.
5. Tighten bolts A - E 20 ft. lbs. (27 Nm). Fig. Main bearing torque sequence-3.7L engine.

https://www.autozone.com/repairguides/Commander-2006-2007/Specifications/Torque-Specifications/_/P-0996b43f8075a69a

First step-----45ft pound
Second step-----65ft pound
Third step--------65ft pound
Fourth step-------another 1/4 turn

The 12mm head bolts torque to 15 ftlbs.
the 10mm head bolts torque to 9 ftlbs.
crosshatch pattern for the sequence.

Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Tighten the cylinder head bolts. Tighten the cylinder head bolts is sequence to 29 Nm (3.0 kgf-m, 22 ft. lbs.). Use a beam-type torque wrench. When using a preset type torque wrench, be sure to tighten slowly and do not overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt and retighten it. Make sure the threads are clean, new heads bolts are best.

Thanks for using FixYa.

To install:

1. Install a new head gasket on the engine, making certain it is positioned correctly. The cylinder head dowel pins and the oil jet must be in place. Refer to the illustrations if necessary.
2. Install the head. Lower it straight down onto the block, aligning it correctly.
3. Apply clean engine oil to the bolt threads and the contact face of the bolt head. Install the head bolts finger-tight.
4. On all models except 1988-89 DOHC Prelude and 1992-95 Preludes with 2.3L and VTEC engines, tighten the head bolts following sequence A. On 1988-89 DOHC Preludes, use sequence B. Use sequence C on 1992-95 Preludes with 2.3L and VTEC engines.
   1. On 1984-89 Accords and 1984-91 Preludes, tighten the bolts in two passes. The first pass should bring the bolts to about 22 ft. lbs. (30 Nm). On the second pass, tighten the bolts to their final torque of 49 ft. lbs. (68 Nm).
   2. On 1990-93 Accords, tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 78 ft. lbs. (108 Nm).
   3. On 1994-95 Accords and 1992-95 Preludes, the bolts are also tightened in three passes. Tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 72 ft. lbs. (100 Nm).
      
      

      Fig. Fig. 9: Cylinder head bolt torque sequence A
      
      
      
      

      Fig. Fig. 10: Cylinder head bolt torque sequence B
      
      
      

      Fig. Fig. 11: Cylinder head bolt torque sequence C
      

   
   
5. If applicable, assemble the intake and exhaust manifolds to the head. Use new gaskets.
6. If applicable, install the cam, rockers and camshaft holders.
7. If equipped, install the EGR crossover and air suction pipes.
8. Connect the exhaust pipe to the manifold using new nuts.
9. Install the timing belt.
10. Install the valve cover.
11. Install the cylinder sensor (if equipped) and the distributor.
12. If applicable, install the alternator.
13. Install the power steering pump, then connect the inlet hose to the pump.
14. Install the accessory drive belts. Adjust the belt tensions.
15. Install the heater hoses.
16. Install the cruise control actuator if it was removed.
17. Connect the spark plug wires. Connect all the wire harnesses and vacuum hoses to the cylinder head, intake manifold and throttle body/carburetor.
18. Connect the throttle control cable and/or accelerator cable at the throttle body.
19. Connect the fuel lines.
20. Install the brake booster, PCV and charcoal canister vacuum hoses.
21. Install the air cleaner and intake duct.
22. Refill the engine coolant. It is recommended that the engine oil be changed whenever a cylinder head is removed.
23. Connect the negative battery cable.
24. Start the engine, allowing it to idle. Bleed the cooling system. Check the work area carefully for any signs of fluid leakage or any indication of the timing belt rubbing or slapping the covers.

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using FixYa. Roger

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): Foot pounds (Final torque) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. Foot pounds (Final torque) Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Cylinder Head Bolt (Preferred Method) All Bolts First Pass in Sequence 22 ft.lb Long Bolt Final Pass in Sequence 75 deg. Medium Bolt Final Pass in Sequence 65 deg Short Bolt Final Pass in Sequence 55 deg. Cylinder Head Bolt (Optional On-Vehicle Strategy) First Pass in Sequence 26 ft.lb Second Pass in Sequence 44 ft.lb Final Pass in Sequence 66 ft.lb

here is the sequence pay close attention to the numbers in the brackets

(8) (5) (9)
(12) (4) (1) (13)
(11) (7) (3) (2) (6) (10)

Note : 12 and 11 are at the vey front of the vehicle:
the torque sequence is as follows
step 1) torque all bolts to 22 foot pounds
step 2) turn bolts as follows
short bolts an additional 55 degrees
medium bolts an aditionl 65 degrees
long bolts an additional 75 degrees