Question about 1993 Isuzu Rodeo

1 Answer

Cant get the cv joint to come out of the front housing

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

Sometimes they are very hard to get out . it will need a large prey bar not a large screwdriver . it will take a little force between axle & trans mabe hammer to smack axle free. you will have to remove the outer caliper, rotor, spindle and bottom ball joint suspension befor e step one

Posted on Dec 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove axle from front of 1998 windstar


  1. Raise and support the vehicle safely.
  2. Remove the front wheels.
  3. Insert a steel rod into the brake rotor to prevent the rotor from turning and loosen the axle wheel hub nut. Discard the nut.
  4. Remove the ball joint-to-front wheel knuckle retaining nut. Drive the bolt out of the front wheel knuckle using a punch and hammer.
  5. Remove the front brake anti-lock sensor and position it out of the way.
  6. Separate the ball joint from the front wheel knuckle using a prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing.
Use care to prevent damage to the front wheel driveshaft joint boot.
  1. Remove the stabilizer bar link at the front stabilizer bar.
Make sure the CV-joint puller does not contact the transaxle shaft speed sensor. Damage to the sensor will result.
  1. Install a CV-Joint Puller (T86P-3514-A1) or equivalent between the inboard CV-joint and the transaxle case.
  2. Install a CV-Joint Extension (T86P-3514-A2) or equivalent into the puller and hand-tighten.
  3. Using an impact slide hammer, remove the driveshaft from the transaxle.
Do not allow the front wheel driveshaft and joint to hang unsupported. Damage to the front wheel driveshaft joint may result. Do not wrap wire around the front wheel driveshaft joint boot. Damage to the boot may result.
  1. Support the end of the driveshaft and joint assembly by suspending it from the chassis using a length of wire.
Never use a hammer to separate the outboard front wheel driveshaft joint from the wheel hub. Damage to the outboard front wheel driveshaft joint threads and internal components may result.
  1. Separate the outboard front wheel driveshaft joint from the wheel hub using a Front Hub Remover/Replacer (T81P-1104-C) or equivalent. Make sure the hub remover adapter is fully threaded onto the hub stud.
Do not move the vehicle without the outboard CV-joint properly installed, as damage to the bearing may occur.
  1. Remove the front wheel driveshaft and joint assembly from the vehicle.
To install:
Do not reuse the retainer circlip. A new circlip must be installed each time the inboard CV-joint stub shaft is installed into the transaxle differential.
  1. Install a new retainer circlip on the inboard CV-joint stub shaft by starting one end in the groove and working the retainer circlip over the inboard shaft housing end and into the groove. This will avoid overexpanding the circlip.
A non-metallic mallet may be used to aid in seating the retainer circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV-joint stub shaft.
  1. Carefully align the splines of the inboard CV-joint stub shaft housing with the splines in the differential. Exerting some force, push the inboard CV-joint stub shaft housing into the differential until the retainer circlip is felt to seat in the differential side gear. Use care to prevent damage to the inboard CV-joint stub shaft and transaxle seal.
  2. Carefully align the splines of the outboard front wheel driveshaft joint with the splines in the wheel hub, and push the shaft into the wheel hub as far as possible.
  3. Temporarily fasten the front disc brake rotor to the wheel hub with washers and two lug nuts. Insert a steel rod into the front disc brake rotor and rotate clockwise to contact the front wheel knuckle, to prevent the front disc brake rotor from turning during front wheel driveshaft and joint installation.
A new front axle wheel hub retaining nut must be installed.
  1. Manually thread the front axle wheel hub retaining nut onto the outboard CV-joint stub shaft housing as far as possible.
A new bolt and nut must be used to connect the front suspension arm to the knuckle.
  1. Connect the front suspension lower arm to the front wheel knuckle. Tighten the nut and bolt to 40-55 ft. lbs. (54-74 Nm).
  2. Install the front brake anti-lock sensor.
  3. Connect the front stabilizer bar link and tighten to 35-45 ft. lbs. (47-65 Nm).
Do not use power or impact tools to tighten the hub nut.
  1. Tighten the front axle wheel hub retaining nut to 157-212 ft. lbs. (213-287 Nm).
  2. Install the front wheels and lower the vehicle.
  3. Using the recommended type of fluid, fill the transaxle to the proper level.

Jul 07, 2014 | 1998 Ford Windstar

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

1 Answer

Is there a c clip in the front driver side holding the half shaft in on a 05 ram 2500 diesel. Trying to replace universal!


There is a spring-type C-clip on the end of the CV housing spline shaft. Disengage the CV joint from the axle housing by using a pry bar between the CV joint and the axle housing. It can be pretty tough to get it to let go. I have found it helpful at times to place the end of a pry bar on the back of the CV housing (as good as I can) and smack it with a BIG hammer. Putting it back in is not nearly as hard.

Jul 09, 2011 | 2005 Dodge Ram 2500 Truck

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

2 Answers

Ticking noise in front left wheel housing during turn


drive axle bearing or worn out shaft ,,

Aug 03, 2010 | 2005 Audi A6

2 Answers

Axle will not come out of the axle housing


I quote from service manual

1 . Raise and support the truck. Remove the rear wheels, the brake drum or brake caliper and rotor. If this is a disc brake, support caliper with wire. Remove seal retainer nuts from axle
housing.

2 . Pull out the axle shaft from housing. Remove the snap ring and bearing race from the axle shaft. Cut the bearing retainer. Break the bearing cage using a hammer and chisel and remove cage and rollers.

3 . Remove the oil seal, the seal retainer and the parking brake assembly (rear). Using a hydraulic press and bearing splitter, press the inner race from axle shaft. Inspect axle shaft for seal wear. Ensure that the shaft is not bent.

2989d8f.jpg

Mar 03, 2010 | Isuzu Trooper Cars & Trucks

1 Answer

Do I have to remove the control arm to replace the half shaft on a 2005 Ford Freestar?


no, here's the procedure for 2002 windstar, should be similar. please rate, thanks.

NOTE: This procedure applies to both the LH and RH halfshaft assemblies.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the front wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Insert a steel rod in the brake disc to prevent the halfshaft from turning while removing the front axle wheel end nut.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The front axle wheel end nut is a torque prevailing design nut. Do not reuse it.
    Remove the nut and washer.
    • Remove the steel rod in the brake disc.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Remove or tape the brake pads to prevent them from falling out of the anchor plate.
    s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the bolts and position the disc brake caliper aside.
  1. Remove the front brake anti-lock sensor harness from the clip.
  1. Remove and discard the nut and bolt.
    • If necessary, use a punch and a hammer to drive the bolt out of the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Position the end of the pry bar outside the bushing pocket to avoid damage to the bushing.
    s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the front wheel driveshaft joint boot (3A331).
    Separate the front suspension lower arm from the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use a hammer to separate the front wheel driveshaft joint (3B413) from the wheel hub. Damage to the joint threads and internal components can result.
    Using the special tool, press on the front wheel driveshaft joint until it is loose in the wheel hub.
  1. Rotate the front wheel knuckle rearward, while pulling it outward at the bottom and remove the front wheel driveshaft joint from the wheel hub.
  1. Using a pry bar, separate the inboard CV joint housing assembly (3B436) (3B437) from the transaxle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the differential seal.
    Remove the halfshaft assembly with both hands.
Installation
  1. Lubricate the differential seal.
    • Use MERCON® V Automatic Transmission Fluid XT-5-QM or equivalent meeting MERCON® V specifications.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install a new circlip every time you remove the halfshaft from the vehicle.
    On the RH side halfshaft only, install a new circlip in the groove in the inboard CV joint stub shaft.
    • Start one end in the groove and work the circlip over the shaft and into the groove. This will prevent the circlip from over-expanding.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inboard CV joint housing assembly and the differential seal.
    NOTE: If necessary, use a non-metallic mallet to aid in seating the circlip in the differential side gear groove (RH) or inboard CV joint housing (LH). Tap only on the outboard front wheel driveshaft joint.
    Align the inboard CV joint housing splines with the differential side gear splines (RH) or output shaft splines (LH), and push the inboard CV joint housing assembly inward until the circlip seats in the differential side gear (RH) or inboard CV joint housing (LH).
  1. Align the front wheel driveshaft joint splines and the wheel hub splines, and push the joint into the wheel hub as far as possible.
  1. Install the washer and the old nut. Using the old nut, seat the front wheel driveshaft joint in the hub. Remove the old nut and discard it.
  1. Connect the suspension lower arm to the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install a new bolt and nut.
    Install the new bolt and nut.
  1. Insert a steel rod in the brake disc to prevent the halfshaft from turning while installing the new front axle wheel end nut.
  1. Apply a small patch of Loctite 242 or equivalent meeting Ford specification WSK-M2G351-A5 to the last five front wheel driveshaft joint threads.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install and tighten the new front axle wheel end nut to specification in a continuous rotation. Stopping the rotation during installation will cause the nylon lock to set incorrectly. This will cause incorrect torque readings while tightening the nut, and lead to bearing failure. Always install a new front axle wheel end nut after loosening the nut, or when the nut has not been installed to specification in a continuous rotation.
    Install and tighten the new nut to specification in a continuous rotation.
    • Remove the steel rod from the brake disc.
  1. Position the disc brake caliper and install the bolts.
  1. Install the front brake anti-lock sensor harness in the clip.
  1. Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.
  1. Check and, if necessary, fill the transaxle to the correct level with the specified fluid. For additional information, refer to Section 307-01 .

Nov 15, 2009 | 2005 Ford Freestar

1 Answer

Where can I find the rubber seals for the ball joints that houses the cv joints on the front axle for a nissan safari ldv '89 model


If you are refering to those corrugated rubber boots, it is highly recommended to replace those CV shafts as the dirt and moisture contamination is not a good thing in CV joints. Dirt and moisture are the leading causes of CV shaft failures. You can by the boots as a repair boot and those wrap around the CV shaft/joint area and bolt together. If you are talking about the little rubber boots on the ball jonts themselves at the end of a steering link, those boots are not sold individually. They only come with new Ball joint assemblies.

Aug 04, 2009 | 1987 Nissan Pickup

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

Not finding what you are looking for?
1993 Isuzu Rodeo Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...