Question about 2000 Jeep Grand Cherokee

1 Answer

HOW DO I CHANGE THE WATER PUMP ON A 99 JEEP GRAND CHEROKEE ?

I need a step by step on how to replace a water pump on a 99 Jeep Grand Cherokee with a 4.0

Posted by on

  • 1 more comment 
  • ronnie9471 Feb 23, 2009

    cant get the clutch fan off because the water pump pulley moves and I cant find anything to brace it on my wife is driving me crazy to fix it please help

  • Anonymous Mar 15, 2014

    water pump replacement 2005 jeep grand cherokee lorado v6

  • Anonymous Mar 28, 2014

    HYDRAULIC PUMP

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

At least you have the 4 liter 6. Once you get all the **** out of the way its like replacing a W/P on an "old school" engine, very much like a Ford or Chevy straight 6. 1) Remove radiator top retainer (the metal U that looks like its the top of the radiator (#13 or 14mm sockets I think). 2) To completely get if off you also have to remove the grill (4-6 phillips screws), then 3) unbolt it from the tubular bumper retainers underneath the grill. 4) DO NOT remove the latch cable - no need. 5) Remove the top bolts holding down the fan shroud. Lift the shroud off its bottom "tabs" and push over the fan. 6) Using #10mm socket remove fan from fan clutch, then remove bolts holding fan clutch onto water pump pulley. 7) Pull out shroud, then fan, then fan clutch. Be very patient, lots of wiggling may be needed. 8) Locate belt tensioner on idler puller below the Power steering pump. Losen very little the pulleys center bolt (10mm), then use a 10mm w/entension to losen the pulley's tension (use counter clockwise/normal rotation to losen). 9) Draw a diagram of the belt routing - you will Never remember it correctly otherwise. 10) Tap the w/p pully and pull if off - do not hit radiator fins! 11) Drain the radiator (clockwise/right rotation opens petoc from factory radiators - counterclock used on aftermaket rads). 12) Remove lower raditor hose at radiator, then at pump (it will be a challenge). 13) Remove upper radiator hose from rad and from thermostat housing. 14) losen the Rubber heater hose from the metal hose screwed into the W/P. 15) Remove 4 bolts from W/P (13 or 14mm I think). The one at the 4oclock position is longer than the others. One is hidden at 6oclock.
16) Remove 2 bolts (14-15mm??) on bottom of Power Steering mount - these go through the W/P case to the block. You may also need to losen the top PS bolts so the PS Bracket can be loose at the W/P case. 17) Wiggle the W/P out from under the PS bracket. and pull off. (16b if needed, remove the upper idler pulley near the A/C unit.) 18) Remove the Thermostat (upper hose return) housing. Scrape off old gasket. Replace with 160deg or 190deg thermostat. Use silicone on gasket. 19) Carefully use a 17 or 19mm box wrench to remove the metal heater hose return line from the upper part of the old water pump. Coat threads with spark plug thread antiseize and screw onto new W/P. 20) Install new W/P gasket w/silcone, be careful to Not block the water holes. 21) Slide W/P under the P/S bracket and jiggle into place. Hand thread one of the top bolts to hold the W/P in place. 22) Insert the P/S bracket bolts and lightly tighten. 23) Jiggle W/P around and insert other bolts, start with the 6oc hidden bolt. Add remaining bolts and tighten to 25 or 250?ftlb (about 3/4 past socket-snug). 24) Tighten ALL P/S bolts. 25) Adjust metal heater pipe. Reinstall rubber heater hose. 26) Reinstall W/P pulley and Fan clutch, and upper idler if it was removed. 27) Thread NEW Belt on pulleys. 28) Tighten tension on idler. Tighten idler axle bolt. 29) Install lower rad hose. 30) Slide shroud over pulleys. 31) Install fan on clutch. 32) Clip shroud retainer bolt mounts back on top of radiator. 33) Install shroud. 34) Connect upper hose. 35) Reinstall radiator retainer. 36) Bolt retainer to Tubular bumper mounts. 37) Reinstall grill. 38) Wonder where the extra bolts etc are supposed to go. 39) Cuss - pray -cuss - pray. 40 ) sip some beer. 41) carefully inspect everything to ensure its back to the way it looked before (several pictures from a digital camera taken during the disassembly will help). 42) Close the rad petok. 43) Add 1 gallons of antifreeze. 44) Start engine and add another gallon of A/F. 45) Turn heater controls to HOT inside (no need for fan). 46) Water guage should show 180 to 210F. 47) Add 1 gallon of water. 48) Install New 18PSI rad cap. 49) Turn off engine and add water or A/F to overflow tank. 50) 1 hour later open Cap to see if level has settled. Add Water as needed to fill rad.

Posted on Dec 31, 2008

  • sbricker Mar 06, 2011

    I replaced the water pump on my wife's 99 Grand Cherokee with the 4.0 liter inline 6 yesterday. I found this helpful, but I just wanted to advise others that they may find some of these steps unnecessary. I suppose some models might be designed a little different depending on what month they were made.

    Steps 1 and 2 were not necessary.

    I removed the fan and clutch fan first, then removed the fan shroud. Getting the fan shroud out was the biggest hassle. It's held on by four 10mm bolts. The one by the lower rad, hose is difficult to get a socket on. You have to remove the top rad. hose to give it clearance to remove it.

    Our Jeep's idler pulley is spring loaded. Use a 1/2" drive rachet to release tension on the serp. belt to remove it from the top pulley. Make sure your diagram is still on the fan shroud. You can remove to belt this first or once the fan and shroud are out of the way.

    There was no need to loosen any of the power steering pump bolts.

    No need to remove thermostat housing unless you want to replace the thermostat while you are at it. I did since it is conv. I use a new gasket and aviation gasket sealer, works great to prevent leaks.

    Break free the bolts on the wp pulley by using wrench on the opposite bolt to keep it from spinning. You can also use a long screw driver on two loostened bolts for leverage to break the last bolt on the wp pulley free. Put the shaft on opposite sides of the loostened bolts (counterpressure)..

    The rest should be pretty straight forward using the provided steps. Best regards.

×

2 Suggested Answers

whispers76
  • 55 Answers

SOURCE: Changing the water pump on 2000 Jeep Grand Cherokee V6

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

motor1258
  • 6674 Answers

SOURCE: Replacing water pump on 2000 Jeep Grand Cherokee V6

Here you go.Clicking on any of the pictures will expand them.
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004319c

Posted on Jan 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much does a water pump replaced cost for a 2003 Jeep Liberty?


Water Pump Replacement Cost for Jeep Grand Cherokee ...

repairpal.com > Estimator > Jeep > Grand Cherokee
This is a national average for all Jeep Grand Cherokee model years, but you can make it more accurate by adding your car info and ZIP. ... When replacing the Jeep Grand Cherokee's water pump, the drive belts and/or timing belt may need to be removed. ...Jeep Grand Cherokee water pumps ...

Water Pump Replacement Service & Cost - YourMechanic

www.yourmechanic.com > Auto Repair and Maintenance Services
How much does Water Pump Replacement cost? Get an estimate instantly. Service, parts, cost & recommendations from YourMechanic. Your definitive guide to ...

Replacing a Water Pump Cost - CostHelper.com


Dec 01, 2015 | 2003 Jeep Liberty

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

2 Answers

Water pump replacement


haynes repair book,,it is good to have if u plan on keeping the truck,,,,tells u step by step,,

Apr 20, 2010 | 1998 Jeep Grand Cherokee

2 Answers

Replace water pump in 93grand cherekee jeep


Here you can find all the information about ZJ-Secc-7-Cooling-System water pump replace and instructions.

Good luck, and remember rated this help.

Aug 12, 2009 | 1994 Jeep Grand Cherokee

1 Answer

I need to replace the water pump on a 97 jeep


there are 4 nuts on the back of the fan and a big nut on the fan shaft turn the one on the shaft toward the right

Apr 11, 2009 | 1997 Jeep Grand Cherokee

3 Answers

Car misses at idle speed


replace fuel pump inside tank

Mar 10, 2009 | 1999 Jeep Grand Cherokee

2 Answers

Replacing water pump on 2000 Jeep Grand Cherokee V6


i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Jan 10, 2009 | 2000 Jeep Grand Cherokee

1 Answer

1999 Jeep Grand Cherokee : Replaced Water Pump and Drive Belt now Jeep won't start?


When you replaced the Water Pump, did you replace the Timing Belt? Any time you replace a Water Pump you have to replace the timing belt because it stretches out. If you did not then most likely your Engine is out of time and there for will not start, but it will turn over. hope this helps, good luck.

Nov 02, 2008 | 1993 Jeep Grand Cherokee

3 Answers

Change a water pump


1. Remove negative battery cable
2. Open radiator valve - drain cooling system
3. Remove cooling fan and shroud
4. Remove belt
5. Remove water pump pulley from hub
6. Remove hoses from water pump
7. Loosen heater hose coolant return tube mounting bolt and nut.
8. Remove the tube. Lose the O-Ring.
9. Remove water pump mounting bolts
10. Loosen the clamp on the bypass hose.
11. Remove the hose as you pull the pump away from the engine.

Hope this helps

Mike

Jun 14, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

2,207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...