Question about 2000 Ford Windstar

1 Answer

Can't find where the red Plastic Tube, in Windstar 2000, fits.

I have a Ford Windstar 2000, 3.8L. After having reinstalled the head gasket, it was impossible to find the place where the red plastic tube, from the back-left intake manifold, fit.
Please let me know if you have an idea or if you know someone who could help me.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The red tube goes into upper coweling amost directly above the the left corner of engine ,it is hard to get on,use mirror or small hands. below fresh air grill and wipers.almost straight up from where it originates on engine.

Posted on Dec 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove headlamp for 1998 ford windstar limited edition


How to remove headlamp James, Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How to Replace the Headlight Bulb in Ford Windstar eHow

Headlight Change 1999 2003 Ford Windstar 2002 Ford Windstar SEL 3 8L V6

1998 Windstar Headlamp Assembly

Mar 24, 2016 | Ford Cars & Trucks

1 Answer

What are the torque specs for intake manifold on a 1998 ford windstar


what are the torque specs for the head and intake as well as

www.justanswer.com > Ford
... as well as - 47. Find the answer to this and other Ford questions on JustAnswer. ...Intake Manifold Support to RH Cylinder Head, 40-55 Nm. Degas Tube to ...

infamous windstar 3.8L intake gasket - Car Forums and Automotive ...

www.automotiveforums.com > ... > Ford > Windstar
Feb 24, 2006 - infamous windstar 3.8L intake gasket Windstar Car Forums. ... In fact, I may have torqued them in sequence initially to a lower value and then again to the final value in sequence. ... Using the Ford manifold torque pattern pictures can be misleading. ... '96 through '98 use pretty much the same intake.
Intake torque specs ' FordForumsOnline.comwww.fordforumsonline.com > Ford Tech Forums > Engine & DrivetrainMay 7, 2010 - 2 posts - ‎2 authorsISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).Torque Specifications - AutoZonewww.autozone.com/.../Ford-Windstar.../Specifications/Torque-...AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Have a 2000 ford windstar heats up lost power


Too many possibilities to get into here. Get a good DIY mechanic to run through ; Engine condition, Cooling system, Drive belts, Compression test for head gasket trouble, Blocked rad, etc etc. You need experienced help. The only thing I advise, is, don't throw parts at it without knowing the problem. Get it properly diagnosed.

Oct 20, 2014 | 2000 Ford Windstar

1 Answer

I have a 1999 ford windstar it over heats


Has the radiator been checked for rust? bet it is red with rust right now from a leaking engine cylinder head gasket, very common in this van. Remove the radiator and have it professionally cleaned and replace the thermostat and flush the engine block and put a can of head gasket sealer in the system on refill with clean new coolant mixed 50/50 with low alkaline water like drinking water from the store..

Aug 08, 2012 | 1999 Ford Windstar

2 Answers

The 2000 Ford Windstar that I have is using water. I fill it up with 2 containers of antifreeze and the next evening it needs some more added. I do not see any visible leaks in the driveway or when it is...


Engine coolant that is disappearing and leaving no visible trace is NOT a good thing. You most likely have a blown head gasket or a cracked cylinder head. (engine coolant going out the exhaust) Also check your oil to make sure the water is not getting into your crankcase. If it is, the oil will be over-full and will look like a chocolate milk-shake.

Aug 03, 2011 | 2000 Ford Windstar

2 Answers

My head gasket from my ford focus td1 estate year


NO, it has to be made to fit each car.
There is no universal gasket.

Jan 14, 2010 | 2000 Ford Focus

1 Answer

Lower radiator hose connecting tube to water pump. how do i remove and replace old metal tube 2000 ford windstar


remove the radiator hose remove the two bolts that hold the tube on and buy new tube and replace is in reverse order.

Jun 17, 2009 | 2000 Ford Windstar

1 Answer

Coolant in # 1 cylnder\clean intake port of intake manifold


Check the lower intake gasket again the new gaskets that are being use made out of plastic with rubber port seals sometimes don't seal right I still used gasket sealer with the new plastic gasket even if it has rubber seals. MY 4.2 v6 had that problem but I went ahead and replaced the head gaskets also just to cover all the bases. And my F-150 has 210,000 miles on it. Make sure you tight the bolts I know it probably calls for something like 8 ft lbs which to me is not tight enough. Double it.

Apr 18, 2009 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...