Question about Toyota Corolla

1 Answer

Replace front wheel bearing 95 - Corolla Toyota Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 21,981 Answers

If you dont have the tools forget it ,not a diy weekend job.remove the centre hub by removing the suspension and lower track arm take out retaining circlip .VERY BIG HAMMER remove bearing and use use old bearing casing to hammer in the new bearing .press is better ,this is not a weekend mechanic job

Posted on Dec 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lost right front wheel while driving. no studs in hub. wheels very rusty. what caused studs to come out?


now you have to replace hub bearing to put wheel back.I pull out 95 chevy hub bearing still OK.

Feb 24, 2013 | 2003 Pontiac Montana

1 Answer

Front bearings and seals on 95 geo tracker replacement


Click here to see how to replace front wheel bearing.Here are the bearings.

Dec 16, 2012 | Cars & Trucks

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

Replace front wheel bearing. How? 95 Oldsmobile Cutlass ciera


remove front tire ,brake caliper ,rotor and axle nut its gona be a hub bearing it has 3 bolts holding it

Apr 02, 2010 | 1995 Oldsmobile Cutlass Ciera

2 Answers

How do I fix the front wheel berrings in a 95 buick lesaber


the bearing is a sealed bearing located inside of the steering knuckle. you need to take off the wheel,use a puller to remove the bearing & then you need to press the new bearing into the housing. depending on your ability and tools this might be a job for a pro

Mar 02, 2010 | 1995 Buick LeSabre

1 Answer

95 nissan 4x4 truck. four wheel drive light comes but does'nt en


the front axles have pinon gear box that the shaft from the transfer case goes to, it has a vacuum hose to it or a solenoid actuator check these for proper function this is how the power is turned on to the wheels.

Feb 13, 2010 | 1990 Nissan Hardbody King Cab

1 Answer

Noise in front passenger wheel of Lantra '95 on turning. Any suggestions?


You have a wheel bearing going out. Get it replaced as soon as possible, to prevent further damage.

Oct 26, 2009 | 1995 Hyundai Elantra

3 Answers

Replace front wheel bearing is it hard to do on 2002 alero


its actually pretty easy if you have the basic tools needed and a little mechanical knowledge, because i dont think you can buy just the bearing at a auto parts store. they sell you the whole hub assembly which is great for the DIYer.

lift the car off the ground and block it from rolling and place a jack stand under it so it cant fall on anyone.


Wheel Bearings printpage_icon.gif

Removal & Installation

These vehicles are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are non-serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    WARNING DO NOT allow the caliper to hang unsupported from the brake hose.


    Front wheel Halfshaft nut and washer Caliper from the steering knuckle and support it aside


    Brake rotor Anti-lock Brake System (ABS) connector, if equipped 3 hub/bearing assembly bolts Halfshaft from the hub/bearing assembly Hub/bearing assembly

    0900c1528023b277.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the front hub/bearing assembly


To install:
Install or connect the following:

Hub/bearing assembly onto the halfshaft, making sure the splines engage smoothly Hub/bearing assembly to the steering knuckle. Torque the bolts to 70 ft. lbs. (95 Nm). Anti-lock Brake System (ABS) connector, if equipped Brake rotor Caliper onto the steering knuckle. Torque the bolts to 38 ft. lbs. (51 Nm). Halfshaft nut. Torque the hub nut to 284 ft. lbs. (385 Nm) on nuts colored black, or 173 ft. lbs. (235 Nm) on gray colored nuts. Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Jul 27, 2009 | 2004 Oldsmobile Alero

1 Answer

RELACING WHEEL BEARINGS IN A 95 JEEP GRAND


Front wheel bearings can be done at home rear wheel bearings will require a hydraulic press and an axle puller. Either job can be difficult depending on amount of rust and availability of tools. The front wheel bearings are an assembly and once the jeep is up on jack stands, with the tires, brake calipers, and rotors removed, it is only a matter of removing the axle nut and 3 bolts (which can be difficult depending on rust) holding in the old bearing assembly

Feb 22, 2009 | 1995 Jeep Grand Cherokee

2 Answers

1995 Toyota Celica Front Wheel Hub


can u replace the bearing in the hub? will that fix your problem?

May 25, 2008 | 1995 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

941 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...