Question about Toyota Camry

1 Answer

I HAVE A FRIEND WHO'S REPLACING THE ALTENATOR IN MY 2002 TOYOTA CAMRY. HE'S GOT ALL OF THE BOLTS OFF, BUT CANNOT FIGURE OUT HOW TO LOOSEN THE ALTENATOR BELT.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 59 Answers

There is a tensioner that you have to move with a wrench. if you remove the passenger side plastic inner fender and rim, it will make it a lot easier. I had the same problem my friends aunts car like that broke a belt and I had to replace it. tell him to look at it from the side and he will see a little piston that pushes on the tensioner bracket and just push in the direction that would compress the piston. it is very stiff though. he will probably be mad at you and toyota by the time he gets the belt off.

Posted on Dec 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced battery on 2002 camry battery light still stays on ??


If its a brand new battery you proberly have a short

Dec 25, 2012 | 2002 Toyota Camry

1 Answer

REPLACING ALTERNATOR 2002 FORD ESCAPE 4X4


this is a very simple job,remove all upper covering and stand back and take a good look .you should see two or three bolts with nuts on then loosen and pull out,replace with new altenator,replace all bolts and replace belt get a strong pole /bar and force altenator to stretch belt once on alt tighen lossly until you are happy.With belt at a good streachyou should have only about 5/6 mm at the furtherest points or what the handboob says .adrian,,,,

Jun 28, 2010 | 2002 Ford Escape

1 Answer

Replace starter on 2002 toyota camry


Jack up car remove 2 or 3 bolts, undo 3 wires and it comes right out.

May 09, 2010 | 2002 Toyota Camry

2 Answers

Replace altenator 2002 bmw 325ci


disconnect the negative battery. remove the belt by rotate the tensioner roller clockwise. from the left car side u will see three hexagon screw 13mm under the altenator. loose out the screw and remove the altenator. before that unplug the two wire behind the altenator.tq

Feb 28, 2010 | 2001 BMW 325

1 Answer

How do i tighten the altenator belt


Loosen the altenator mounting bolts, pull the altenator so the belt tightens and re-tighten the mounting bolts.

Feb 05, 2010 | 1994 Toyota Pickup

1 Answer

How to remove alternator, 2002 camry


Disconect neg terminal of battery. Should be two bolts holding alternator in place loosen those, at the bottom in front of the engine locate a pulley place a wrench in this and pull up to loosen belt, then remove. . Remove.

Jul 17, 2009 | 2002 Toyota Camry

1 Answer

Power steering belt on 1991 toyota camry


Locate the idler pulley. Loosen the nut in the center of the idler pulley. Then loosen the bolt that protrudes from the back of the pulley. This will let the belt go slack.

Jul 16, 2009 | 1991 Toyota Camry

1 Answer

I dont have a diagram to run serpentine belt to a toyota camry 03


Hi

Replacing Serpentine belt on a Toyota camry 2003—


Step 1--Examine the belt placement of your Toyota Camry fan belt so that you will remember how to put it back once you have removed it. Refer to the vehicle owner's manual for further information. Locate the pivot bolt on the front passenger side of the engine. Loosen the pivot bolt with a socket wrench.


Step 2--Loosen the adjustment locking bolt that is just below the tensioner pulley with a socket wrench, and then loosen the tensioner pulley to allow the belt to move free.


Step 3--Check the belt for any signs of cracking or irregular wear, so you can fix any problems that may exist with the pulleys. Remove the fan belt from the pulleys on the engine and take it out of the engine compartment.


Step 4--Wrap the new fan belt around each of the pulleys the same way it came out. When you have the belt in place, tighten the tensioner pulley with a socket wrench.


Step 5--Tighten the adjustment locking bolt and the pivot bolt with a socket wrench, and then look over the engine to check that everything is back in place.


Step 6--Turn the vehicle engine on and watch it for a few minutes to verify that everything is operating properly, then turn the engine off.


Please refer to these links for serpentine belt diagrams—

Serpentine belt on a Toyota camry Link 1

Serpentine belt on a Toyota camry Link 2

Please do accept the solution and revert for further assistance.

Thanks
Rylee

Jul 13, 2009 | 2003 Toyota Camry

1 Answer

How to replace outside rearview mirror on 2002 toyota camry


on the door there should be a plastic panel in the area of the mirror if not take the door panel off then you should see the bolts holding the mirror in place may be 2 or 3 .reverse the process and youre good to go.

Jul 06, 2009 | 2002 Toyota Camry

2 Answers

Replace alternator belt only for 1993 toyota camry


loosen the mounting bolts on the alternator, remove the old belt, replace with the new belt, slightly tighten the top mounting bolt, pull the alternator up until the belt is tight or if there is an adjustment bolt, crank down until tight (shouldn't bow more than 1"), and tigten other hardware.

Mar 28, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...