Question about 2001 Chrysler 300M

Open Question

2001 Chrysler 300m ABS codes #15 and #17

Please advise on these codes. Per shop need new ABS control Module? Could this be because we replaced our rear brakes? Was told codes mean Left & Right rear speed sensor signal failure respectively. Please help.

Posted by on

5 Suggested Answers

emissionwiz
  • 71525 Answers

SOURCE: ABS light permanantly ON. recommend replace ABS module $$$$$$$$$$

I would go with the ABS module, if the shop is wrong make them fix what the real problem is for free, is this a Jag dealer?

Posted on Dec 11, 2008

  • 6 Answers

SOURCE: 1999 Chrysler 300m ATC Control Communication Failure

i have the same car and it did the same thing when i got it take it to a dealership there are 2 flashes for the bcm body control module that will recalibrate the automatic temp contol and that should fix the problem

Posted on Apr 01, 2009

  • 1 Answer

SOURCE: 93 Plymouth Voyager Bendix-10 ABS failure.

I have had the same problem on two Chysler vans..(1993 and 1994).. the ABS brakes on these cars are the pits.. Dodge will charge you big $$$ to replace the whole unit (which will break again).. plus they don't honor LIFE TIME warranty... The solution..
Rip out the ABS..and put normal brakes in..it's not big deal and will cost about $150. You need a Brake Booster, Master Cylinder, Proportion valve and a Brake pedal... and a Saturday.. I've done it twice now.. I got all the parts (via the internet) from a junkyard in illinois (a common 'Kit" that they sell)

Posted on Apr 13, 2009

  • 396 Answers

SOURCE: Engine light and ABS traction control light remain

The ABS sensor is a speed sensor also for Traction Control. This is why both lights are on , One of your front ABS sensors are bad or disconnected, or has a pinched wire.

Posted on Jan 16, 2010

  • 279 Answers

SOURCE: Where is the lighting control module located on a

It's in what Chrysler calls the "junction block". What normal people call the fuse box. The fuse box is located at the driver's end of the instrument panel. You need to open the driver's door to see and remove the cover plate that hides it.
Charlie

Posted on Aug 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can leaky shocks on a 2006 Cadillac DTS cause the traction control light to come on


If the light is on there are DTC'S - diagnostic trouble code's stored in ABS - anti - lock brakes computer . Have codes checked first , something wrong with electrical part of antilock brakes , I know, what does ABS have to do with traction control ! traction control is a function of the ABS control module . Leaking shocks ? clarify , air shocks etc.... Before you start guessing , have it check for codes .
This vehicle is equipped with the TRW 440 V antilock braking system.
The vehicle is equipped with the following braking systems:
?€¢
Antilock Brake System (ABS)


?€¢
Engine Drag Control (EDC)


?€¢
Dynamic Rear Proportioning (DRP)


?€¢
Traction Control System (TCS)


?€¢
Vehicle Stability Enhancement System (VSES) (w/JL4)

The following components are involved in the operation of the above systems:
?€¢
Electronic brake control module (EBCM)--The EBCM controls the system functions and detects failures.


?€¢
Electronic brake control module (EBCM)--The EBCM controls the system functions and detects failures.


The EBCM contains the following components:


-
System relay--The system relay is energized when the ignition is ON and no ABS DTCs are present. It supplies battery positive voltage to the solenoid valves and pump motor.


-
Vent tube--The vent tube, located in the EBCM connector, is an opening to the internal cavity of the EBCM. It allows ventilation of the EBCM internals.


?€¢
Brake pressure modulator valve (BPMV)--The BPMV contains the hydraulic valves and pump motor that are controlled electrically by the EBCM. The BPMV uses a 4 circuit configuration with a diagonal split. The BPMV directs fluid from the reservoir of the master cylinder to the left front and right rear wheels and fluid from the other reservoir to the right front and left rear wheels. The diagonal circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other.


Important: There is a rubber isolator located under the BPMV and on the mounting studs. The rubber isolators protect the BPMV and the EBCM from vehicle vibrations.


?€¢
The BPMV contains the following components:


-
Pump motor


-
Inlet valves (one per wheel)


-
Outlet valves (one per wheel)


-
Master cylinder isolation valves (one per drive wheel)


-
Prime valves (one per drive wheel)


?€¢
Wheel speed sensors (WSS)--As the wheel spins, the wheel speed sensor produces an AC signal. The EBCM uses this AC signal to calculate wheel speed. The wheel speed sensors are replaceable only as part of the wheel hub and bearing assemblies.


?€¢
Traction control switch--The TCS is manually disabled or enabled using the traction control switch.


?€¢
Stoplamp switch--The EBCM uses the stoplamp switch as an indication that the brake pedal is applied.


?€¢
Lateral accelerometer sensor (w/JL4)--The EBCM uses the lateral accelerometer sensor as an indication of the lateral acceleration of the vehicle.


?€¢
Yaw rate sensor (w/JL4)--The EBCM uses the yaw rate sensor as an indication of the yaw rate of the vehicle.


?€¢
Steering wheel position sensor (SWPS) (w/JL4)--The EBCM uses the SWPS as an indication of the position and rotation of the steering wheel.


This systems are very complex , your best bet would be to take it to a qualified repair shop .

Oct 18, 2016 | Cadillac Cars & Trucks

2 Answers

What is a abs modular on a Escalade Cadillac?


Jesse, The module will not stop fluid to rear brakes, a bad master cylinder will,leaking lines, air in brake system, faulty metering block if equipped, collapsed flex lines or pinched brake line faulty caliper or brake cylinders,etc. will cause the possible feeling of no rear brakes.
(ABS Module components) the ABS speed sensors and the ABS control module . When the brake is applied, the ABS control module reads the speed data from the speed sensor and sends the correct pressure to each wheel to prevent any wheel lock up, eg. sliding/skidding Links below have more info.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Service Stability System AND abs Pump issue

ABS Control Module Replacement Service Cost YourMechanic

https://www.rockauto.com/en/catalog/cadillac,2002,escalade,5.3l+v8,1431695,brake/wheel+hub,abs+control+module,1844

Feb 24, 2016 | Cars & Trucks

2 Answers

How to diagnose an ABS problem


You need to find out what code is stored in the ABS control module, if the light is on there is a DTC an the system is disabled ! Don't know if auto part stores can pull ABS codes or not , You'll have to check it out . Personally I say take it to a ASE certified repair shop if you don't know anything about anti lock brakes !
?€¢
Electronic Brake Control Module (EBCM) -- The EBCM controls the system functions and detects failures.


The EBCM contains the following components:


?€¢
System Relays -- The inlet and outlet solenoid relay is energized when the ignition is ON and no ABS DTCs are present. It supplies battery positive voltage to the solenoid valves, the pump motor relay is energized and supplies battery positive voltage to the pump motor when ABS is activated.


?€¢
Brake Pressure Modulator Valve (BPMV) -- The BPMV contains the hydraulic valves and pump motor that are controlled electrically by the EBCM. The BPMV uses a 4 circuit configuration with a diagonal split. The BPMV directs fluid from the reservoir of the master cylinder to the left front and right rear wheels and fluid from the other reservoir to the right front and left rear wheels. The diagonal circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other.


This system can store 10-12 DTC's for something simple as wheel speed sensors to wiring problems to a malfunction of the EBCM . Some of these problems you would need a professional type scan tool ! The antilock brake system on your vehicle is the
BOSCH 8.0 antilock braking system
The vehicle is equipped with the following braking systems:
?€¢
Antilock Brake System (ABS)


?€¢
Dynamic Rear Proportioning (DRP)


?€¢
Traction Control System (TCS) (w/NW7)

The following components are involved in the operation of the above systems:
?€¢
Electronic Brake Control Module (EBCM) -- The EBCM controls the system functions and detects failures.


The EBCM contains the following components:


?€¢
System Relays -- The inlet and outlet solenoid relay is energized when the ignition is ON and no ABS DTCs are present. It supplies battery positive voltage to the solenoid valves, the pump motor relay is energized and supplies battery positive voltage to the pump motor when ABS is activated.


?€¢
Brake Pressure Modulator Valve (BPMV) -- The BPMV contains the hydraulic valves and pump motor that are controlled electrically by the EBCM. The BPMV uses a 4 circuit configuration with a diagonal split. The BPMV directs fluid from the reservoir of the master cylinder to the left front and right rear wheels and fluid from the other reservoir to the right front and left rear wheels. The diagonal circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other.


Important: There is a rubber isolator located under the BPMV and on the mounting studs. The rubber isolators protect the BPMV and the EBCM from vehicle vibrations.


?€¢
The BPMV contains the following components:


-
Pump Motor


-
Inlet Valves (one per wheel)


-
Outlet Valves (one per wheel)


?€¢
Wheel Speed Sensors (WSS) -- As the wheel spins, the wheel speed sensor produces an AC signal. The EBCM uses this alternating current signal to calculate wheel speed. The wheel speed sensors are replaceable only as part of the wheel hub and bearing assemblies.


?€¢
Traction Control Switch (w/NW7) -- The TCS is manually disabled or enabled using the traction control switch.


?€¢
Stop Lamp Switch - The EBCM uses the stop lamp switch as an indication that the brake pedal is applied

Sep 21, 2015 | 2006 Saturn ION

1 Answer

2006 Ford F350 4wd dually. Had ABS light come on. Found rear brakes bad. Replaced roters, calipers, brakes, brake lines and all new seals in rear dif. Rebuilt front dif, new seals, new brakes, roters,...


It doesn't cost anything to ask a question at a ford dealership . I would call and just explain what's going on. That one has me stumped. Good luck !!

Oct 29, 2013 | 2006 Ford F 350 Super Duty

1 Answer

Brake warning lights


Many repair shops can read the ABS codes also - especially shops that specialize in tires and brakes.

The codes will likely identify if a specific wheel sensor is mis-behaving / failing, or a worst-case situation: the ABS Control Module is failing (expensive).

The sensors, located behind each wheel, can be checked for accumulated road 'gunk' and cleaned. Also look for any frayed/broken sensor wires.

NOTE: The sensor sit about .25" away from a gear-type ring on the backside of the wheel - the 'exciter ring'. It's the teeth passing in front of the sensor that creates the signal sent to the ABS control module.
NOTE: The ABS Control Module reads the speed of each wheel and 'pulses' the level of braking to each wheel according to if it thinks it is skidding on ice/wet surfaces.
Problem with the Anti-Lock Brake System. Take it to a professional and I believe it means the Antilock Brake System is disengaged. Means a code has been stored in the abs computer. Standard obd tester cannot check these codes. Take to dealer service shop.

Jun 04, 2013 | 1998 Ford Expedition

1 Answer

No fluid at rear brakes on 1995 Olds Cutlass Supreme. I took it into a shop and the code said ABS motor was bad. Would be the cause of no brake fluid coming out when I take banjo fitting off?


Hello
The ABS in this car is what is called Active ABS, so yes a defective ABS Hydraulic control unit motor can cause this problem. Other things that can cause the problem is a defective brake master cylinder or Air trapped in the ABS control unit. You do not say you have done any parts replacement. If this problem did start after any brake system repair then be advised it takes a special tool that electrically holds open the ABS control valves so the air can be removed through bleeding, so if you opened yup the system you must have a shop with the proper tool do the bleeding. There is no way to bleed the brakes at home using conventional brake bleeding means.

Oct 06, 2011 | 1995 Oldsmobile Cutlass Supreme

2 Answers

1999 Olds Silhouette -- Problem - ABS & Brake Traction light "coming on" on the instrament panel. Brake fluid level "full". Brake pads & shoes "new". No brake fluid is getting to the REAR brakes....


The ABS light is on because there is a fault in the abs system, The traction control uses the abs system so it will also not work if the abs is not working. You'll need to scan the ABS module to see what code is stored in its memory. Once you have the code you'll have a better idea of what needs to be repaired.

Sep 27, 2010 | Oldsmobile Silhouette Cars & Trucks

1 Answer

I have a 1987 bmw 535is, I replaced the abs pump,and bled the system, the left front brakes and rear right are not working. only two wheels are braking. how to solve this


normally abs system use two seperate module unit. each module control the front and rear whell by crossside like u said the front left and rear back are disfuntion. maybe ur replacement abs module have prob or trie 2 bled again

Mar 27, 2010 | 1987 BMW 5 Series

3 Answers

Anti Lock lamp comes on after a minute or so.


this could be anything from a bad sensor to moisture in the system. also it could be your ABS control module. a variety of scan tools have an option in it to retrieve ABS codes. then you just look it up and go from there (best bet would be have a shop scan it its cheaper than buying the scan tool and chances are they will tell you based on the code what the problem could be)

Oct 28, 2009 | 1989 Acura Legend

2 Answers

Here is a Problem for you all! 2000 Grand Am GT ram air v6 ABS and Brake light always on, No trouble codes, and no rear brakes at all key on or off. Has fluid at M/C and to ABS unit but not from unit to...


This problem sounds like and ABS module that has gone bad, the ABS module has toothed gears inside that actuate the ABS motor, if one of these gears slips a tooth or "unwinds" itself if will not circulate brake fluid to where it needs to go (ex: the rear brakes) alot of times the brake and ABS light will come on, but will not set any trouble codes. My recommendation is to take this to a repair shop and have them verify the problem and replace the ABS module, the motor gears have to be properly aligned when replacing or the lights will stay on and you will still have the same problem. Hope this helps.

Mar 10, 2009 | 2000 Pontiac Grand Am GT

Not finding what you are looking for?
2001 Chrysler 300M Logo

Related Topics:

296 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

71338 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7018 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...