Question about 2000 Ford Expedition

1 Answer

Trying to remove driver side door panel to replace lift motor

Posted by on

  • laurafranzon May 11, 2010

    how do you remove the window/door lock switches and the door handle? I see no screws. What inside mirror cover? Where can I find a diagram?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Correct Procedure;
Inside mirror cover pry's loose, Remove.
Remove window/door lock switches.
Remove inside door handle.
Here is the Trick.
Inside trim lifts right straight UP!
DO NOT PRY OUT. If you pry out, you break retainers and will cost you a trim pad.
If it is tough, use a rubber hammer at the bottom to start the trim pad in an upward position. Reinstall in reverse.

Posted on Dec 23, 2008

6 Suggested Answers

  • 187 Answers

SOURCE: How do remove drivers side door panel

First you need to remove the door handle and window crank by pushing back the ring and releasing the handles. Also the arm rest will have screws into the steel door frame that must be removed. The panel itself has plastic snaps that are pushed into holes in the doors steel frame. The trick is to slide a pry bar or even two is better, one on ether side of the clip and force the pin out. You need to be patent and do one at a time. The door panels are made of a less than hard strong material and will brake apart easily especially if they are older. The clips go all the way around the lower three sides and the top will lift off the sill.

Posted on May 07, 2009

honeymokey
  • 3113 Answers

SOURCE: trying to replace drivers window lift motor. help!!

Tape and secure window, replace rivets with 1/4 nut and bolts.

Posted on May 12, 2009

  • 1 Answer

SOURCE: how do i remove the drivers side door panel? need to access wiring to replace the drivers side mirror.

how do i replace the side mirror on 94 acura integra

Posted on May 29, 2009

  • 119 Answers

SOURCE: want to remove driver side door panel to gain access to power window motor

first remove the tweeter speker if equipped this comes off easily by gently prying from behind, then remove the small panel behind pull handle you"ll find a screw behind it\remove that,the next part is a little tricky the door grip needs to come off to achieve this place a small flat screwdriver at the top of the handle and pry forward the turn handle counterclockwise and this will release it from the clips you"ll then find 2 screws one at the top other at the bottom of door grip remove those and then gently pry from the bottom of the door panel to release the retaining clips thats it

Posted on Jul 14, 2009

  • 1986 Answers

SOURCE: 99 Buick LeSabre, how do I remove driver side door panel to replace power window motor?

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

2 Answers

My rear lift gate does not unlock. The rest of doors do, it is a four door. Also my front drivers side window does not roll up or down. Here again JUST the drivers window, the rst roll up and down. Could...


They are not related ...
The lift gate locking mechanism can be accessed by removing the interir trim pannel on the gate ... and locating the locking actuator and replacing it...
The same can be done for the power window motor ... remove the interior trim panel and replace the power window motor...

Hope I helped !!

Oct 06, 2010 | 1999 Jeep Grand Cherokee

1 Answer

How do I remove the driver side door panel to replace window motor


1. Remove 2 small screws at bottom of the door panel (6mm)
2. Remove small black cover from inset for door handle (pry it out carefully with a small flat head screw driver or panel removal tool) and remove bolt behind it (8mm)
3. Pop window/door lock control panel out with the same flat head screw driver and disconnect all connectors. Remove small screw from behind it (6mm)
4. Lift straight up on door panel and then tilt toward you.
5. Disconnect mirror control connector.
6. Squeeze two tabs on the door latch assembly and it can be removed along with the cable. DONE.

Jul 02, 2010 | 1999 Ford F150 Regular Cab

2 Answers

The driver's side electric window will not roll back up is there a part I can buy to fix it?


Driver's side window motors get used far more than any other window motor on the truck. They frequently burn out. It is also possible that the switch is bad but the motor is more likely. Just buy a motor from a junkyard or a parts store and test it per below and put it in. The only tough part is getting the door panel off. Be careful not to destroy it in the process. Remove all visible screws (including those hidden in the finger well) and carefully pry the panel away from the door. Anywhere you run into resistance look carefully, figure out what is holding the panel, and get it off. You can test the motor once you get into the door. There are two wires going to the motor. One of them needs to be hooked to a hot lead from the battery positive post and the other to a ground lead from the door frame. Reverse the polarity to reverse the motor. If the motor works it almost has to be the switch but it is almost always the motor.

Mar 19, 2010 | 2001 GMC Yukon XL

1 Answer

How to replace interior door latch on elantra?


Remove any and all screws from the door panel, including removing lock and window controls. then take a large flat-tipped screwdriver and pry off the panel all the way around. FInally lift panel up and off the door. Now you will have access to the inside of the door. Everything from here is self explainable.

Dec 07, 2009 | Hyundai Motor 1999 Elantra

1 Answer

Need to find a way to take off the drivers side window motor


Motor
  1. Disconnect the negative battery cable.
  2. Remove the door trim panel and watershield.
  3. Detach the motor wires at the multiple connector.
  4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
  5. Remove the motor from inside the door.
To install:
  1. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
  2. Connect the power window motor wiring.
  3. Connect the negative battery cable.
  4. Check window operation.
  5. Install the watershield and door trim panel.

Door Panel
  1. Disconnect the negative battery cable.
  2. Snap out the two door pull strap retaining screw covers. Remove the screws.

CAUTION To avoid breakage of the door pull covers, insert a small screwdriver diagonally between the pull strap and chrome bracket. Snap out both sides then remove.


  1. Remove the two screws on the front and rear side of the front door trim panel.
  2. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.

NOTE Do not use the front door trim panel to remove the trim clips from the door inner panel. Replace any bent, damaged or missing push pins.


  1. Remove the window regulator switch housing from the back of the front door trim panel. Lift up the housing and disconnect all connectors from the switch housing.
  2. Disconnect the driver seat regulator control processor switch if equipped.
  3. Twist out the interior lamp wire assembly.
To install:
  1. Ensure that the plastic watershield is secured to the door .
  2. Position the front door trim panel to the door. Connect the interior lamp wiring.
  3. Align door lock side to its mating slide on the sheet metal.
  4. Snap in the front door trim panel. Ensure all retainers fit properly. Install the two retaining screws on the front and rear side of the front door trim panel.
  5. Connect the driver seat regulator control processor, if equipped.
  6. Position the window regulator control switch housing and connect the switch connectors. Install it to the front door trim panel by snapping it in, or by installing the screw at the rear.
  7. Install the two retaining screws and pull strap covers.
  8. Connect the negative battery cable.
053777a.gif

Aug 27, 2009 | 2000 Lincoln Town Car

1 Answer

Trying to replace drivers window lift motor. help!!


Tape and secure window, replace rivets with 1/4 nut and bolts.

Apr 28, 2009 | 1990 Buick LeSabre

1 Answer

Unable to remove adriver's side door panel containing electrical


You have to remove the door panel. To do so, you need to remove all screws visible. Next, remove the panel by popping off the door panel itself. You need a tool sold at the auto parts store....looks like a funky type of screwdriver. You slip it in between the door and the door panel and pop the plastic "buttons" loose. Make sure you look for all the screws so you are not yanking on a fastner that is still attached.

Then you have to lift up and wiggle at the same time.

Mar 29, 2009 | 1989 Buick LeSabre

1 Answer

Driver side power window motor not functioning


It is the motor. Remove the inner door panel. Lower the window and remove the glass. 2 10mm nuts and window will lift out. Winow has to be in postion where you can reach the nuts through port holds in door. Knock out the center pins on the rivets holding the motor in. Unplug motor. Drill out the rivets and remove the motor. Replace motor and re rivet or screw it back in with bolts, nuts and loc tight. replace window and door panel and you are done. the charge for someone who does this all the time is 1.5 hours labor.

Mar 21, 2009 | 1998 Chevrolet Cavalier

1 Answer

How to replace the window lift motor on a 1990 GMC S-15 Jimmy


Remove the door panel,there will be several rivits you will have to drill out,replace the motor replace the motor and the rivits you drilled out with bolts.

Jan 01, 2009 | 1990 GMC S-15 Jimmy

Not finding what you are looking for?
2000 Ford Expedition Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...