Type and size bulbs for a 2005 buick lacrosse
Refer to the owners manual or go on line to obtain one free HERE
SOURCE: how do i change the low-beam bulb on my 2005 buick
there should be 2 brackets at the rear of bulb housing, 1 may have a small bolt.....lift these up and the headlamp housing should come out. you will see how it works when you get it apart.
SOURCE: 2006 buick lacrosse how to replace headlight low
The bright light fitting is the same as the dim so take it apart fist to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you a little more space.
SOURCE: Replace headight assembly on 2005 buick lacrosse
The procedure to replace head light assembly on buick lacrosse is as follows:---
1)To remove and replace the headlight assembly you will need to remove 1 retaining bolt on the top of the headlamp assembly and 2 sliding retainers at the rear.
2) The carefully Pull up the retainers and that will release the headlight assembly and allow you to pull it out the front.
3) When installing the new headlight assembly make sure you have it lined up correctly before trying to install the retainers, don't force them it may get cracked .
4) Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise.
5) Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light.
6) On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again.
7) Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw.
8) Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough.
Note:-- The turn signal is part of the headlight assembly on your 2005 Buick LaCross.
9) To replace the headlight bulb you need to remove the front bumper cover.
10)To release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit.
11)To remove these locking pins, pull or pry up the little tab in the center of the pin.
Thanks.
SOURCE: replace thermostat on 2005 buick lacrosse
hello there:
to replace the thermostat you will need to fallow the upper radiator hose back to the intake you should find two bolts holding the thermostat housing remove the bolts and you should find the thermostat under the housing you will need to remove the hose this will help you out and before in stalling clean gasket surface on both sides..... please leave a review thanks sincerely D.Jones
SOURCE: HOW DO I CHANGE THE
Asuming you mean taillight/turnsignal, and not highmounted brake light:
1.open the trunk
2.Remove 4 wingnuts on trunk trim (there are two on each side)
You can do it by only removing 2 on one side, but it makes a nicer job,
3.Pull back the trunk "trim" the carpeted cardboard
4.Remove 2 wingnuts which hold the taillight assembly in place
Pull out the taillight assembly; you might want to remove (i.e. unattach or unplug) the wiring harness
5.Turn the particular bulb's socket (there's 5 back there: 2 tail, 1 back up, 1 side marker, 1 brake/turn) counterclockwise, and it removes from the assembly, holding the bulb.
6. Pull out bulb and replace.
6. Reverse steps to reassemble.
128 views
Usually answered in minutes!
×