Question about 2000 Honda Accord

1 Answer

How do I replace a headlight on a 2000 Honda Accord?

The headlight burned out.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 37 Answers

Hi

Step 1: Remove Wire Harness. Find the wires and their harness connected to the back of the bulb. To make sure you have the right harness, wiggle it while looking through the clear lens. If the bulb moves while wiggling the the harness, you have the right one. To remove the harness, simply pull it straight back away from the bulb and off the bulb prongs.
Step 2: Remove Rubber Seal Boot. Note the orientation of the boot (typically, the two rubber tabs extending out the back are at the 12 and 6 o'clock positions). The most exposed edge of the boot is underneath the bulb when viewing from above. Feel underneath for the edge and peel it back away from the bulb housing. Work your way around the bulb housing peeling more of the boot back as you go. You may have to work your way around a few times to complete disengage the boot from the bulb housing. Don't worry about the part of the boot around the bulb prongs. It will slide off easily once the boot is disengaged from the bulb housing.
Step 3: Open Wire Clip. The bulb is held in place by a wire clip. DO NOT unscrew this clip! Find the tab opposite the screw, push it toward the front of the vehicle then pull it up vertically. The wire clip will pivot back. It pivots on the anchor held by the screw.

Posted on Dec 22, 2008

  • k530i Dec 22, 2008

    Step 4: Remove Bulb. Once the wire clip is open, the bulb is
    just resting in the bulb housing. Note the bulb orientation since the
    new bulb will have to go in the same way (typcially, the three prongs
    are in the 9, 12, and 3 0'clock positions). Simply pull it out and
    maneuver it out of the bulb housing and past the wire clip.


    Step 5: Install New Bulb. Practice closing the clip and opening
    the clip without a bulb in the housing. Once you get a feel for it,
    move the clip out of the way and place the new bulb in the. WARNING:
    KEEP BULB CLEAN -- no contaminants and no fingerprints. Handle the bulb
    by the metal prongs and maneuver it into the housing in the same
    orientation as the old bulb.


    Step 6: Close Wire Clip. Close the wire clip over the new bulb as you practiced in Step 5 ;p


    Step 7: Install Rubber Seal Boot. Maneuver the boot into the
    same orientation it was in before removal. Place the center hole of the
    boot over the bulb prongs. Push the bottom edge of the boot onto the
    bulb housing and work your way around until it is fully engaged with
    the housing.



  • k530i Dec 22, 2008

    Step 8: Connect Wire Harness. Align the wire harness to the bulb prongs and push it on.



    Step 9: Test. Turn on the headlights and make sure it works.


    Step 10: Drink.


    For Driver's side bulb remove the housing over the air intake before
    starting. The two fasteners pull straight out with a little tug with
    pliers. Save fastners, you will need them to reinstall cover later.

    Same procedure as passenger side now except that space is VERY
    TIGHT. Be gentle with the wirecage move, as rescrewing the cage
    probably couldn't be done with conventional tools and you will end up
    back at the shop to have them pull battery and air cleaner to get in to
    this space.

    Good luck. I am sure the dealers charge at least $100 to do
    this paininthea** job. So you are saving some dough for the aggro.
    Owners manual actually has a reasonably good diagram and I recommend
    looking at it.



×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 honda accord headlight


check the earth wire for dirty /rusted terminal as this is typical of voltage fluctuations the blow bulbs.

Jun 04, 2013 | Cars & Trucks

2 Answers

Honda accord keep burning low beam headlights


Sounds to me like you need to reset the headlight housings... maybe they are vibrating very badly. ... OR, easy fix, get NEW headlight housings on EBay and install.

Nov 28, 2011 | 2004 Honda Accord

2 Answers

Honda accord repair manual


The closest discount auto store should have it, or Haynes.com at this link http://www.haynes.com/products/productID/194

Mar 13, 2010 | 2000 Honda Accord

1 Answer

Have a 2000 honda accord sedan. need to know


Pop open the left side and follow the same pattern. ;o)

Sep 15, 2009 | 2000 Honda Accord

1 Answer

How can i change headlights for my honda accord 2000.i want to replace the headlights for my honda accord 2000 car. can i do myself amd how


open the hood and reach behind the lights. There should be a ring, turn this plastic ring until it stops and the bulb should come right out, theres probably a better explanation in your manual

Jun 20, 2009 | 1999 Mitsubishi Mirage

1 Answer

How do I replace a headlight on a 2000 Honda Accord?


I HIGHLY recommend CrystalView Headlight Cleaner. It is about $30, they sell it at auto stores and even Wal-Mart. It cleaned my dirty headlights very nicely. Follow the instructions perfectly and you wont be let down, I assure you.

While you're at the auto-store, you can find your replacement bulbs (REPLACE BOTH HEADLIGHTS!!) in the books the stores provide.

Dec 29, 2008 | 2001 Honda Accord

1 Answer

How to assemble a 2000 honda accord headlamps


Its actually pretty straight forward. Disconnect the headlight. Then their are two bolt on the top the the headlight. Remove those then remove the wheel of the car. Then their are three more bolts bellow the headlight All three facing from the outside of the fender to the center of the car.

Then once you have those 5 bolts out. Pull the headlight forward and up. Their are two tabs that go into the fender.

Dec 06, 2008 | 2000 Honda Accord

1 Answer

I can't figure out how to replace the front turn signal


There is one screw on top of headlight assembly that holds turn signal lens in place you have to remove that screw and pull lens straight out. As far as head lamps go its just a matter of getting your hand behind headlight assembly to remove the collar that holds the bulbs in place.

Nov 11, 2008 | 2000 Honda Accord

1 Answer

2000 Honda Accord Headlight Assembly


what i suggest i can suggest is, buy a clear sealant, and seal the sides of the headlights.

the reason why is air can creep in tha lamps that's why it gets moisture (foggy) and dirty.

hope it helps.

Aug 24, 2008 | 2000 Honda Accord

Not finding what you are looking for?
2000 Honda Accord Logo

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...