Question about 2007 GMC Envoy Denali

Open Question

Air compressor for level ride not working

Fuse for level ride air compressor location not listed on fuse box cover.

Posted by on

6 Suggested Answers

  • 3 Answers

SOURCE: Air Suspension Fuse 2000 Lincoln town Car

look in ur manual it will say it in there or u can call ur dealer and ask them which fuse it would be......

Posted on Apr 09, 2009

  • 4369 Answers

SOURCE: rear air suspension compressor not engaging.

what year? here's 2003 rear air only info, not 4 wheel air.

you have a fuse panel in truck and 1 under hood.




Visual Inspection Chart Mechanical Electrical

  • Restricted suspension movement
  • Excessive vehicle load
  • Cut, severed or crimped air line(s)
  • Unmounted height sensor
  • Damaged air spring(s)
  • Open fuses:
    • Central junction box (CJB) Fuse 4 (15A), 6 (5A) and 20 (5A)
    • Battery junction box (BJB) Fuse 109 (50A)
  • Loose, corroded or disconnected connectors
  • Air suspension switch is in the OFF position
  • Damaged solenoid valve(s)

  • compressor is inoperative
  • BJB Fuse 109 (50A).
  • Air compressor assembly.
  • Circuitry.
  • Air suspension relay.
  • Go To Pinpoint Test P .



----------------------------------------------------------------------------

The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.

Air Suspension Switch
The air suspension switch supplies power to the air suspension control module. Without the air suspension control module receiving this power, the load leveling system is inoperative and will not react when the rear of the vehicle is raised or lowered. If the air suspension system is disabled by turning off the air suspension switch, a "CHECK SUSP" will appear in the RH corner of the instrument cluster with the ignition in the run position.
Air Compressor
The RAS air compressor:
  • consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • is a single cylinder electric motor driven unit that provides pressurized air as required.
  • is powered by a solid state relay which is controlled by the air suspension control module.
  • passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • air drier has a single port.
  • air drier may be replaced separately.
  • incorporates a snorkel that may be replaced separately.
The vent solenoid:
  • allows air to escape from the system during venting actions.
  • is part of the air compressor cylinder head.
  • has a 1,103 kPa (160 psi) internal relief valve.
  • shares a common electrical connector with the air compressor motor.
  • is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • has an O-ring seal that prevents air leakage past the valve tip.
  • opens when the air suspension control module determines lowering is required.
  • provides an escape route for pressurized air that opens when system pressures exceed safe operating levels.
  • is replaced with the air compressor as a unit.
Air Spring
RAS vehicles use air springs in the rear. The air springs provide a varying spring rate proportional to the systems air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system air. Increasing air pressure (compressing) raises the rear of the vehicle while decreasing air pressure (venting) lowers the rear of the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the air suspension control module.
The two air springs support the conventional rear leaf coil springs.
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.
  • A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing the vehicle and related components.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
Solenoid Valve, Air Spring
s2j~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Never rotate an air spring solenoid valve to the release slot in the end cap fitting until all pressurized air has escaped from the spring to prevent damage or injury.
The air spring solenoid:
  • allows air to enter and exit the air spring during leveling operations.
  • is electrically operated and controlled by the air suspension control module.
  • is only installed as a unit.

Posted on Apr 18, 2009

ancdlm
  • 58 Answers

SOURCE: air ride suspention front 1996 lincoln continental

It sounds to me like your compressor got killed. What probably happened is that the airbag got a hole or tiny crack in it so the compressor has to work extra hard because it is like blowing up a balloon with a hole in it. Therefor the airbag killed the compressor. I would recommend going to strutmasters.com and taking a look at our conversion kits. these convert you from the airbag to a powder coated American made steel coil spring that is guaranteed to last the life of the car. I added the link below so you can check it out.
http://www.strutmasters.com/lincoln-suspension-parts-s/1.htm

I hope I was of some help
Good Luck!!!

Posted on May 06, 2009

  • 61 Answers

SOURCE: air ride air compressor not working 2003 yukon denlia

On your 2003 yukon denali, the air ride compressor is located on the driver side rear frame rail on the outboard side, near the fuel filler neck and behind the left rear wheel. Hope this helps!

Posted on Jul 24, 2009

ZJLimited
  • 17970 Answers

SOURCE: I need a fuse Box diagram for a 2002 Jeep Liberty

In here you can find all about fuses and wires: Jeep-KJ-2002-Liberty-Service-Manual-PDF-Secc-08-Electrical-Systems check this:
* Page 469 Wiring Table of Contents

I hope help you with this. Good luck (remember rated this help).

Posted on Sep 08, 2009

  • 1 Answer

SOURCE: '98 Chevy Venture Air compressor quit working

i found one fuse under the hood its top left corner small one that is a 30a

Posted on Nov 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wheres the air condition fuse


More often than not, it is actually caused by improper pressure in the system. The Clutch for the a/c needs a certain amount of pressure to function, and any drop in pressure wont run the compressor.
You should have the pressure checked, but if you would like to check the fuse, look by the kick panel for the fuse box, and on the back side of the cover, it will list each fuse. locate and check the fuse, as well as the fuse box under the hood.

Jul 24, 2014 | 1996 Ford Explorer

2 Answers

Lift sensor for rear of 1988 Deville


To begin with, check the "ride level" fuse and make sure that the ride level compressor does work, and you should be able to hear that the ride level compressor is working when the ride level system is leveling the vehicle.

The ride level system uses an air compressor and either an air type of shocks or a type of air billow to raise and lower the vehicle, there is an adjustment to set the ride height and it is located under the vehicle and there is a control lever or rod that should be connected between the rear axle and a switch that is mounted on the body of the vehicle, and there will be an adjustment slot in the control lever between the switch and the body, and that is how you would adjust the ride level height, but be sure that the vehicle can not drop any further down if someone is under the vehicle trying to adjust the ride height.

However, you might find that the control lever to the ride level has fallen off from the switch on the body or it has come loose from the rear axle, and it is just hanging there not operating the switch on the body that controls the the ride level compressor, or there might be a blown out air shock or billow, or you might find that an air line from the compressor is leaking and the ride level compressor will just run continuously until it blows out the fuse, and if that is the case you might also find out that the air compressor has burned out from running continuously.

I hope that this information will help you to solve your ride level problem.

Jun 04, 2010 | 1988 Cadillac Sedan DeVille

1 Answer

Electronic level control not working right in a 1999 cadillace deville, what can i do to fix it?


To begin with, check the "ride level" fuse and make sure that the ride level compressor does work, and you should be able to hear that the ride level compressor is working when the ride level system is leveling the vehicle.

The ride level system uses an air compressor and either an air type of shocks or a type of air billow to raise and lower the vehicle, there is an adjustment to set the ride height and it is located under the vehicle and there is a control lever or rod that should be connected between the rear axle and a switch that is mounted on the body of the vehicle, and there will be an adjustment slot in the control lever between the switch and the body, and that is how you would adjust the ride level height, but be sure that the vehicle can not drop any further down if someone is under the vehicle trying to adjust the ride height.

However, you might find that the control lever to the ride level has fallen off from the switch on the body or it has come loose from the rear axle, and it is just hanging there not operating the switch on the body that controls the the ride level compressor, or there might be a blown out air shock or billow, or you might find that an air line from the compressor is leaking and the ride level compressor will just run continuously until it blows out the fuse, and if that is the case you might also find out that the air compressor has burned out from running continuously.

May 23, 2010 | 1998 Cadillac DeVille

1 Answer

Rear suppenion low to the ground


There is an air compressor mountedmabove the rear suspension. The fuse for the air ride suspension is located behind the trunk rear trim panel. There is a level sensor on the rear control arm. If fuse is good, check for power at plug feeding compressor, compressor failure common. With suspesion at low position, sensor should send power to compressor. if no power suspect height sensor. Check relay for power and operation although failure rare.

Dec 25, 2009 | 1999 Cadillac DeVille

1 Answer

Location of the fuse to the compressor of rear air shocks. I do not have original fusebox lid.


auto level fuse box is located at rear of car under near suspension carrier, all fuses and relays to do with level ride are there, good luck.

Oct 20, 2009 | 2002 Cadillac Deville

2 Answers

Where is the fuse for the air ride compressor on a


the fuse in under the hood in the main fuse box, if your standing over the front drivers side tire, it will be on the far left 4th fuse down, marked RTD/ real time damping..... i believe the fuse is marked 30....

Sep 22, 2009 | GMC Yukon Denali Cars & Trucks

3 Answers

Air ride is not working


were is the fuse located for the air ride

Jun 09, 2009 | 1999 Cadillac DeVille

3 Answers

Service ride control


The fuse is called RTD 30 amp under the hoodfuse box. That is for the Air Compressor.

Parts.com has the best price for:

Rear Suspension:
Shock W/auto level control - 1500 series

and under
electrical:
then ride control components
then compressor

May 03, 2009 | 2006 GMC Yukon Xl Denali

2 Answers

Air Ride on 1994 Buick Park Avenue


You have what is called a height/load leveler switch located on rear axle of vehicle .Check to see if the arm (which moves and kicks on compressor when ride height is low) Is connected and moving freely..You then might want to make sure that the air supply lines atatched to air shocks or air bags are not leaking.. If all checks out fine and you decide to disable compressor you can do this by unplugging harness that connects to compressor...And then you can manually adjust your ride height by adding air to the valve on compressor (it resembles a tire valve stem) this will adjust your your ride height and you can let air out at same location if lower height is desired.. This is a little inconveinient but will bypass automatic system as you requested.

Dec 26, 2008 | 1991 Buick Park Avenue

2 Answers

Air ride not working


Is there power at the compressor? If not, check the level switch located at the rear of the vehicle (connects the rear axle to the body via a small arm that moves with body up/down motion)

Sep 13, 2008 | 1995 Buick Riviera

Not finding what you are looking for?
2007 GMC Envoy Denali Logo

Related Topics:

373 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...