Question about 1992 GMC Jimmy

1 Answer

I was driving in 4wd on the snowy highway when I heard a grinding noise. I pushed the 4wd button and the noise stopped. Do you know whys this might have happened and what damage I may have caused trying to get to a stupid hockey game, that was cancelled! Thanks so much for your help. Becca

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Most likely you snapped the 4WD chain in the transfer case. Put it in 4WD go in reverse with the wheel turned if the vehicle does this smoothly than your 4WD is not engaged.

Posted on Jan 25, 2018

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: noise while driving in 4wd on snowy highway...

i will be honest u probably just need to have the front end serviced. could be the hubs and or bearings....transfercase

Posted on Dec 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes a popping noise from front end, and a rubbing noise , not grinding


4wd?? Check CV shafts. Also look for whats rubbing. whre is the dirt rubbed off.

Feb 26, 2016 | 2005 GMC Yukon

1 Answer

Y do u need 2 buttons 2 use 4wd on 05 gmc


I have a 2003 GMC it has two buttons to use 4 wheel drive as most all do with push button controls...One is for standard highway driving with 4 wheel drive the other is for 4 wheel drive a low speeds for off road driving and conditions that need low speed less spin driving..not designed for highway use..and must be stopped to engage where 4 speed highway can be shifted on the go..hope this answers your question..good luck..

Feb 23, 2015 | 2005 GMC Sierra

1 Answer

I have a 1996 Chevy Blazer. A few days ago, I heard a clunking / grinding noise from underneath when I was turning. Sense, then it has gotten worse and got to the point that it was loud and vibrated the...


This truck should not be operated on the street in 4WD mode. You need to investigate the front axel CV axel shafts as well as the outer axel carrier bearings. Damage to front brake rotors and possible lock down while operating the vehicle. Safety hazard exist, so do not drive until axel and bearings are checked and repaired

Aug 23, 2017 | 1996 Chevrolet Blazer

1 Answer

My "service 4wd" came on and my push button 2wd,4wd, auto 4wd lights are off...is this expensive to fix?


You definitely need to have it serviced & checked out...The service 4WD indicator read across my screen, but I did not have serviced...Eventually, I heard a grinding noise & because I didn't have it serviced when I took it in, it was found that the transfer case had no tranfer case fluid at all...This damaged the transfer case which had to be replaced (used transfer case-$400.00)....The transfer case is part of your transmission...The shape mine was in could have broke my transmission...Have it taken care off before it gets too bad...You must use only GMC Transfer Case Fluid

Oct 21, 2010 | 2003 Chevrolet Tahoe

2 Answers

When switching my truck from 2wd to 4wd, a grinding noise can be heard. The 4x4 only fully engages when i come to a complete stop. Is this a air switch problem or an acuator?


Is it meant to switch from 2 to 4 wheel drive when its moving? if it is then I'd make sure the transmission oil is of good quality and upto the proper level. not a solution just you should do this before suspecting anything else.

Jan 26, 2010 | 2004 Ford F150

1 Answer

2002 Mitsubishi Montero Sport XLS transfer case issue.


The best place for a DIY manual is www.ALLDATADIY.com their info is very accurate.

Jan 29, 2009 | 2001 Mitsubishi Montero Sport 4WD

1 Answer

Noise while driving in 4wd on snowy highway...


i will be honest u probably just need to have the front end serviced. could be the hubs and or bearings....transfercase

Dec 22, 2008 | 1992 GMC Jimmy

Not finding what you are looking for?
1992 GMC Jimmy Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...