Question about 2007 Ford Sport Trac Limited
My 2007 sport trac has a whining noise coming from some where in the middle to back end of the truck. The noise increases with speed and occurs at any speed. When I put my truck in neutrel I hear a tick coming from the front end.
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Torque Specifications Description Nm lb-ft lb-in Brake caliper bolt 32 24 — Brake disc shield bolt 8 — 71 Fuel tank filler pipe bracket bolt 15 11 — Fuel tank filler pipe hose clamps 3 — 27 Halfshaft nut and washer 275 203 — Lower arm inboard bolt 250 185 — Lower arm outboard bolt 275 203 — Parking brake cable bracket bolt 10 — 89 Shock absorber lower bolt 275 203 — Shock absorber rod nut 65 48 — Shock absorber upper mount nut 30 22 — Stabilizer bar bracket nut 48 35 — Stabilizer bar link nut and grommet 30 22 — Toe link cam adjuster nut 275 203 — Toe link outboard bolt 325 240 — Trailing arm bolt 300 222 — Upper arm outboard bolt 225 166 — Upper arm inboard nut 250 185 — Wheel speed sensor bolt 8 — 71 Wheel knuckle bolt 275 203 —
Posted on Mar 30, 2009
Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.
The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.
Posted on Apr 02, 2009
YOUR WHINING IS THE REAR DIFFERENTIAL IS CRYING.THE PINION BEARING PRELOAD OUT OF ADJUSTMENT.AN IMPROPER WEAR PATTERN ON THE RING GEAR.OR BOTH ARE WORN.THIS IS A DEALERSHIP OR A DRIVELINE AND TRANSMISSION SHOP FIX.
Posted on Aug 17, 2009
it has front and rear disc brakes, disc brakes are very simple to change out. Most disc brakes have two bolts that hold them on, one on the bottom one on the top on the inside of the brake caliper, they may be an allen head, or just a bolt. Remove them counter-clockwise. After you remove the two bolts, lift up and away on the caliper and the whole assembly will come off. Once you pull the assembly off you will see the two pads, one of them is driven by a piston, the other one is fixed. Remove the fixed one, they just pop off (have little metal clips you may have to slide the pad off). Take a C-clamp or something comparable to squeeze with, place it on the back of the caliper and on the old pad thereby squeezing the cylinder back into the piston, once you squeeze the cylinder back into the piston, it will give you room needed for thicker new brake pads. Piston should retract with the c-clamp fairly easy, shouldn't be a whole lot of resistance. Remove c-clamp after you get it to retract and remove old pad. Put new pad on, just like you took the old ones off. All four are basically the same to change out, they all have two bolts holding them on. You pull those, get the pistons to retract and replace the worn pads, put them back on, line up holes, put bolts back in... and your good to go. When you get back in the car and turn the key on, you may have to pump the brakes a few times.
Posted on Nov 02, 2009
SOURCE: ford sport trac, 4.0 dry
how many miles on the vehicle? does the noise quieten down when the engine RPMs come up? timing chain is very likely if you have over 150,000 miles. lifter noise is a more common problem. the lifters will tend to quieten down as the RPMs come up due to more oil pressure.
Posted on Jul 30, 2011
Tips for a great answer:
Jan 20, 2017 | 2007 Ford Explorer Sport Trac
Sep 23, 2016 | 2007 Ford Explorer Sport Trac
Apr 25, 2015 | 2007 Ford Explorer Sport Trac
Oct 29, 2013 | Cars & Trucks
Sep 01, 2012 | 2007 Ford Explorer Sport Trac
Nov 18, 2010 | 2007 Ford Explorer Sport Trac
Oct 21, 2009 | 1999 Jeep Grand Cherokee
Aug 17, 2009 | 2004 Ford Explorer Sport Trac
Jun 14, 2009 | 2004 Ford Explorer Sport Trac
334 people viewed this question
Usually answered in minutes!