Question about 1996 Jeep Grand Cherokee

1 Answer

How do I remove front bumper and right fender?

1996 Jeep Ltd. How do I remove the parts? What tools might I need? My son just skidded into a steel fence!

Posted by on

  • Anonymous Mar 17, 2014

    how to remove front bumper on dc ltd

  • Anonymous Mar 31, 2014

    how to remove front fenders

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

What you need is a good half inch ratchet and a breaker bar. Can't tell you what size sockets to use, but you can figure that out. Remove any wiring attached to bumper then loosen bolts that secure it to the frame (it usually helps to spray hardware with good penetrating oil the day before, then again just before you start.) Use breaker bar to get bolts loose... depending upon rust level, sometimes you may need a short pipe over the handle to get more leverage. Don't beat on anything with a sledge hammer or you may trip impact sensor & won't be able to start car afterwards. Otherwise, it's just bolt off, bolt back on and your'e finished!

Posted on Dec 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the front bumper of a Mercedes Benz cl65 amg


Lift the front end of the car and support on stands.
Remove the front wheels.
Remove the fowards under-tray.
Remove the forward halves of the front wheel arch liners.
Unscrew the small down-facing Torx screw at each top rear corner of the bumper.
Gently pry inwards the rear end of the U-shaped steel channel that holds the fender and bumper flanges together.
Pull the channel rearwards to disengage the lugs from the diagonal slots at the forward end, and remove the channels.
Disconnect the external air temp sensor in the bottom left air intake.
Disconnect the parking sensors connector at the right rear corner. You need to open the lever lock and pull hard without damaging the wiring.
Open the hood and remove two bolts on top of the bumper, next to the inner headlamp mountings.
Remove two nuts in lower grille - vertically beneath above bolts.
If its your first time, get a friend and pull the bumper forwards very slowly and gently, avoiding scratching the fenders.
The bumper is surprisingly light.

It will take about an hour.

Jul 02, 2014 | Cars & Trucks

1 Answer

How to remove 1996 accord fender


Remove bumper only the side u need,bolts or plastics clips on top, two or three under the radiator support for bumper, remove head light, under the fender by the end of the bumper is a bolt for the bumper and other for the fender, 4 bolts on top, one bolt inside bi the door hinge, one or two in the bottom under the side plastic skirt .

Jun 04, 2014 | 1996 Honda Accord

1 Answer

Remove front bumber from 1996 honda accord lx


I believe there will be many screws under the car with the splash shield that must be removed. Remove screws/retainers from the fender well liner in each wheel well, but only toward the front (no need to remove the entire thing). Behind the fender liner toward the front of the car you'll see some screws/clips holding the bumper to the front/bottom of the fender.
You'll need to remove each turn signal in the front of the bumper with a long phillips screwdriver. Use a flashlight to look in from the middle of the lower bumper and you'll see a hole where the screw driver goes in (loosen the screw, but it probably wont come out). Pop the lamp assembly out, but don't force it- the opposite side of the lamp has a tab that fits in a slot to help hold it in place.
Look straight back from where the turn signal lamps were removed and you'll see 2 bolts on a metal bracket. There are 2 on each side, behind each lamp. You'll need some long extensions to get all the way in there. Be sure to support the bumper as you take these out, because they are the main support points for the bumper assembly.
Once these are out, the bumper should come off, or at lease you'll see if there were any small screws you missed. FYI, I left almost all of the screws out of my bumper (except one on each side where it attaches to the fender), so all I have to do is remove those 4 main bolts behind the turn signal lights to drop the bumper.

Mar 24, 2014 | 1996 Honda Accord

1 Answer

Replacing a serpentine belt in 90audi quattro


emove wheels and tires.
Remove front part of fender liners.
Remove 3 10mm nuts holding either end of the bumper onto the fenders, which can be seen when you pull the inner fender liners away.
Remove air grilles around foglamps.
Remove bumper bolts just inside and above the grille openings.
Remove bumper cover.
Remove T45(maybe T50?) Torx bolts holding bumper shocks on.
Remove T30 bolts holding the front fenders onto the radiator support.
Pull front lock carrier forward to allow access to front end of the engine.
YOu now have good access to the serpentine belt tensioner.
Compress tensioner, which will allow you to place a drill bit or similar locking tool into the tesnoner rod to keep it compressed.
Replace belt.

Nov 04, 2011 | 1995 Audi A6

3 Answers

My hyundai Santa fe is leaking transmission fluid somewhere at the front of the engine. I can't see it because of the skid plate. Any ideas of what it could be?


Good Evening. Unfortuantely there is no easy path to a right answer here without removing the skid plate. In front of the engine are transmission cooler lines and other miscellania. The best advice i could give you is take down the skid plate and have a can of brake cleaner handy to clean everything off while you have it turned off then have someone turn it on for you so you can visually see where it is coming from. Hope this helps and if you have any more questions feel free to ask.

Aug 14, 2010 | 2004 Hyundai Santa Fe

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

1 Answer

How do you take bumper off a ford puma?


Front Bumper (434230)

Removal
1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

Installation
1. To install, reverse the removal procedure.

Jan 01, 2010 | 2007 Ford F

1 Answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks


Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Oct 09, 2009 | Mercedes-Benz E350 Cars & Trucks

1 Answer

How do you take off the front bumper of a 2003 mitsubishi eclipse gs


you need to remove the headlights there is a pin on the bottom besides the bolts, along the top of the cover is your air cleaner intake remove the two pins, remove the bolts across the top of the cover there should be a steel piece on top of the cover, there are two other steel pieces in the headlight areas they are bolted to the fender, there are two bolts on each side these bolt the cover to the fender, in order to get to these bolts you must remove the plastic pieces under the bumper cover they are attached to the bumper cover and wheel well plastics with push pins, this should get it off or very close

Aug 22, 2009 | 2001 Mitsubishi Eclipse

1 Answer

Replace the face skid in the front bumper


remove front bumper and it should be clear what holding the face skid in place

Sep 29, 2008 | 2008 Honda Pilot

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...