Question about 1994 Buick Skylark

1 Answer

Tension belt pulley needs to be replaced. I have the new pulley and serpentine wrench, but can't get at the tensioner on my 1994 buick skylark 3.1

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

Have you tried going through the fender well?

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Change serpentine belt on 06 sienna


  1. 1 Check to ensure the Sienna's engine is cold, then make sure the Sienna is in park, the ignition is in the off position and the key is removed from the ignition to prevent any possibility of the engine engaging during the serpentine belt replacement.
  2. 2 Open the hood and locate the serpentine belt routing diagram sticker on the side of the engine casing. Study it for a moment before removing the existing belt. It is essential the new belt be installed exactly as the diagram indicates.
  3. 3 Find the tensioner pulley, the main pulley that controls the serpentine belt, and fit a 1/2-inch socket wrench over the self-tensioner on the outside of the pulley.
  4. 4 Pull the wrench to the left to move the pulley forward, which loosens the belt, then remove the belt.
  5. 5 Compare the old serpentine belt with the new, replacement belt for length, width and number of grooves on the belt's underside. Be certain the replacement belt is the right part.
  6. 6 Fit the new belt on to each pulley according to the serpentine belt routing diagram on the manufacturer's sticker, or according to the drawing made prior to removing the old belt. Fit the new belt on to the tensioner pulley last, again applying pressure on the pulley's self-tensioner with the half-inch socket wrench to loosen the pulley.
  7. 7 Release the pressure on the self tensioner and allow the tensioner pulley to ease back into place, thereby tightening the new serpentine belt with the appropriate tension.
  8. 8 Remove the wrench and close the hood.
Thank you and good luck,
Lee

Aug 26, 2010 | 2006 Toyota Sienna

1 Answer

How do I replace the alternator


Hello, Alternators are a car part that can be very costly to fix because of labor costs. But with an hour or two of time and a little elbow grease, you can do it yourself. And to replace the alternator follow the following steps below:

Step 1. Pull your car into the garage or your work area. Turn the car off and let it sit for a while to cool.

Step 2. Begin by disconnecting the negative cable of the battery.

Step 3. Remove the serpentine belt from the pulley on the alternator. Do this by using a socket wrench to turn the serpentine automatic belt tensioner so that it allows slack in the belt. Then simply slip the belt off the alternator pulley.

Step 4. Locate and disconnect all the mounting bolts on the alternator, use a vehicle specific manual if you have any trouble.

Step 5. Disconnect all wires attached to the alternator then remove the alternator from the car.

INSTALLING NEW ALTERNATOR.

Step 1. Slide the new alternator into place. Do not worry about the serpentine belt yet.

Step 2. Replace the bolts that held the previous alternator to secure the new one in place.

Step 3. Attach the wires to the new alternator the same way they were attached to the old one.

Step 4. Adjust the serpentine belt tensioner the same direction you did in Section One to put slack in the belt. Wrap the belt around the pulley of the new alternator and then remove the socket wrench from the automatic belt tensioner.

Step 5. Inspect the belt to be sure it is not snug and follows the path required in the pulley and belt configuration diagram.

Step 6. Hook the negative battery wire back to the negative terminal on the battery.

Thanks






























Jul 20, 2010 | 1995 Buick Skylark

1 Answer

In order to replace the serpentine belt on a 1994 Buick Skylark It appears that something has to be removed in order to remove the belt and replace it. What exactly has to be removed?


Nothing has to be removed. Just relieve the tension on the belt and it will come off. Find the tensioner pulley and pry it back. Look for a square hold where you insert a 1/2" ratchet. If you find none look for a way to pry it back. All you have to do is relieve the tension.

May 09, 2010 | 1994 Buick Skylark

1 Answer

I need a diagram for installing a serpentine belt on a 94 buick skylark Or I need to know where the tensioner is located and once i release the tensioner will i be able to slip the belt around the pulley...


the tensioner will be one of the idler pulleys ,abd then you fit the new belt but make sure you draw a picture of the belt run before remove it

Apr 25, 2010 | 1994 Buick Skylark

1 Answer

How to install a serpentine belt on a 1994 mercury grand marquis it seems that i can get a 3/8 or 1/2in ratchet to move tensioner


It is sometimes pretty tough getting it to move.
Make sure you are Rotating it the correct way.
Do you have a Breaker Bar or a Serpentine Belt Tensioner Tool. Stores like Harbor Freight and even some Auto Parts Stores have these. Some of the auto parts stores have these for rent (for free with a refundable deposit).
I like and use weekly the Serpentine Tool from Harbor Freight (Item #66344-0VGA- $20). It is narrow enough to fit in most tight spots. The main bar has a 3/8-in fitting, and the extension bar can connect to this with a 1/2-in fitting.
The idea is to have more leverage. The Ratchet and/or Wrench sometimes does not provide that leverage needed.

When installing follow the below guidelines. DO NOT try to put the Belt on the Tensioner last.

"HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s).
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 07, 2010 | 1994 Mercury Grand Marquis

2 Answers

Change alternator belt on 1996 buick riviera


The 96 Riviera has a motor mount that interferes with the removal and replacement of the serpentine belt. The motor mount must be loosened and the engine need to be lifted slightly to accomplish the replacement. Not good engineering on this model year.

Aug 26, 2009 | 1996 Buick Riviera

2 Answers

Replace 2000 buick park ave serpentine belt


Firt - study & write down (draw) the belt path,,
and be sure about it..

Then - put a wrench on the nut in the center of the tension pully.. Move the tension pully to loosen the belt.. Pull belt off..

Repeat to put new one on..

Should be pretty easy..

Jul 09, 2009 | 2000 Buick Park Avenue

1 Answer

Changing the serpentine belt


Your vehicle has an automatic belt tensioner. It should be located near the other pullies because the belt runs over it too. Usually required is a ratchet or box end wrench to work it. Once you get the wrench on the pulley, pull the tensioner loose to remove the belt and the reverse to replace it. The vehicle should have a routing diagram for the belt.
I believe the belt diagram is on the left corner on the passenger side.
Good luck and hope this helps

May 02, 2009 | 1997 Buick Skylark

3 Answers

Replace belt tensioner pulley on 1994 buick skylark


You need to put a piece of wood underneath the oil pan and place a jack underneath the oil pan/motor, loosen the motor mounts that are next to the belts, then raise the motor enough to reveal the nuts/bolts for pulley...just dont raise the oil pan so high that you crush it or break something, only enough to be able to reach tension pulley...

Dec 21, 2008 | 1994 Buick Skylark

1 Answer

1993 buick skylark serpentine belt removal


there is going to be a tensioner pulley near the front of the motor on top that you have to apply pressure to or you can loosen the alternator and take it off that way,just remember how it came off so you can put it back on

Aug 13, 2008 | 1994 Buick Skylark

Not finding what you are looking for?
1994 Buick Skylark Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...