Question about Jeep Grand Cherokee

2 Answers

Home link system program?

I have a 1996 jeep grand cherokee limited, it has the home link system in the visor and i would like to know how to program it for my garage etc.

Posted by on

  • Anonymous Apr 23, 2009

    When I press the buttons they do not blink at all.

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

  1. Turn off the engine.
  2. Erase the factory test codes by pressing buttons 1 and 3. Release the buttons when the two green lights begin to flash (about 20 seconds ).
  3. Choose one of the three buttons to train. Position the end of your hand-held transmitter 1-3 inches (5-14 cm) away from the lower left corner of the EVIC display while keeping the display in view.
  4. Simultaneously press and hold both the desired Transmitter button and the hand-held transmitter button. After a short time, the message TRAINING will show on Transmitter display. Do not release the buttons until the message TRAINED appears on the display (this may take as long as 60 seconds ), release both the Transmitter and hand-held transmitter buttons.
  5. Press and hold the just-trained Transmitter button. TRANSMIT should appear on the display. If your device activates when the Transmitter button is depressed and released, programming is complete. To train the other buttons, repeat the process. Be sure to keep your hand-held transmitter in case you need to retrain the universal transmitter. NOTE: If the message TRANSMIT appears on the Transmitter display but your device does not activate, the device may be equipped with a "rolling code" system. Continue with steps six through eight below to complete the programming of a rolling code equipped device (most commonly a garage door opener).
  6. At the garage door opener receiver (motor-head unit) in the garage, locate the "learn" or "smart" button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. Firmly press and release the "learn" or "smart" button. (The name and color of the button may vary by manufacturer.) NOTE: There are 30 seconds in which to initiate the next step.
  7. Return to the vehicle and firmly press, hold for two seconds and release the programmed Transmitter button. Repeat the "press/hold/release" sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming process.
  8. Transmitter should now activate your rolling code equipped device. To program the remaining two buttons, simply repeat the process.

Posted on Dec 23, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

2006 honda odyssey
cant get the homelink to connect to the Liftmaster garage door opener.

Posted on Sep 03, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Keyless remote 1996 jeep grand cherokee laredo programing


Instructions
  1. Programming the First Transmitter
    • 1

      Unlock all of the Jeepicon1.png Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.

    • 2

      Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.

    • Sponsored Links

    • 3

      Point the remote at the receiver (located by the little bulb on the caricon1.png ceiling) and hold down the "Lock" button for up to 5 seconds.

    • 4

      When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.

    • 5

      Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

Feb 11, 2013 | 1996 Jeep Grand Cherokee

1 Answer

How to replace License Plate Bulb '96 Jeep Grand Cherokee Limited


Hi Timmy:

Check this procedure from Repair manual...


LICENSE PLATE LAMP - REMOVAL
(1) Remove screws and license plate lamp visor from liftgate (Fig. 10).
(2) Remove bulb from lamp socket.

INSTALLATION
(1) Install a bulb in lamp socket.
(2) Position license plate lamp visor on liftgate and install screws (Fig 10).


4_28_2012_5_22_57_pm.jpg


Hope this helps.

Apr 28, 2012 | 1996 Jeep Grand Cherokee

2 Answers

Owners manual jeep grand cherokee 1997


The ZJ models, manufactured from 1993 to 1998, originally came in three general trims, the Base, Laredo, and the Limited. I have the same '93 ZJ Limited 5.2L V8, nice engine!!!

Just one in the Internet: Jeep-ZJ-Grand-Cherokee-Manual-de-Usuario (spanish)

Also, its possible that you are interesting in the Repair Manual, just tell me.

Keep in touch.

Feb 01, 2011 | 1997 Jeep Grand Cherokee

1 Answer

1996 Jeep Grand Cherokee window relay


Check in the Fuse Block, the cavity 2, fuse 30 Amp c/Brkr (Section (8W Page 7)

More details about electrical system for ZJ Grand Cherokee, you can find here: ZJ-Secc-8W-Wiring-Diagrams

I hope help you with this (rated this help). Good luck.

Sep 24, 2009 | 1996 Jeep Grand Cherokee

1 Answer

How to set-up visor remote with garage door remote


To program the car to your remote-hold down the 2 outer buttons until the red light blinks or comes on(not sure its been awhile) then put the garage door remote next to the sunvisor, hold down the button on the remote and any button on the sunvisor at the same time until the red light blinks. Thts it.

Mar 06, 2009 | 1996 Jeep Grand Cherokee

1 Answer

My home link system built in the sun visor of my 1996 jeep grand cherokee


Hi, there is no green button, i just bought the same vehicle,and i programed my entrance gate to the home link and worked the first time,all i did was hold my remote right up to the home link and pressed the first button and the remote button the same time until the red light flashed rapidly,and it worked just fine, hope that works

Dec 26, 2008 | 1996 Jeep Grand Cherokee

1 Answer

Help


you haven't solve my problem. where is the horn located on my Jeep.

Dec 20, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

613 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...