Question about Chrysler Town & Country

1 Answer

How do i remove the wiper arms from my 2005 Towm & Country?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 541 Answers

First, please make sure you need to. You don't if you're just changing the wiper blades. I have done this several times over the years with the 4 vans I've owned and found once that I didn't need to pull the wiper arms to get where I needed to go. If you find you must pull them, unscrew the bolt that holds them in place, which is under the plastic cover that will pop off with touch of a small screwdriver. Before you do anything else, mark the wiper arm at the point where it connects to the wiper shaft so you can get it lined up correctly. An alternative is to use some tape on the windshield itself to remind yourself how the blades lined up so you get them back on correctly and without having them move either too far or to little across the windshield. With that done, I have used a battery terminal puller positioned over a towel that will protect the plastic grill under the wiper arms - but try simply pulling the arm off the drive shaft with a forceful tug with bare hands, but odds are it will be frozen. Remember, 1) the drive shaft is at an angle in relation to the windshield, so pulling up will cause it to bind - you have to pull at a slight angle. and 2), grip the wiper arm close to the point where it goes on the shaft, if you pull from too far out you'll bend the arm. If you have to resort to the terminal puller, you need to line things up so you are pulling at a slight angle and put the "arms" of the terminal puller on the outside of the wiper arm and the little post in the middle on the wiper shaft and then turn the handle on the puller. Probably works better with a helper, though I've always done it solo - probably took me longer and created a permanent hatred for having to do this in the first place. Putting a little lube like WD40 on the shaft before you start doesn't hurt. I have also found that a few taps on the lower side of the wiper arm from a rubber mallet while I had tension applied from the terminal puller didn't hurt either. Good luck.

Posted on Dec 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Read wiper. Is sideways to rate wiper arm.


Set wiper arm that is not in the right location to where it is supposed to be and then remove black plastic cap at bottom wiper arm and tighten 15mm nut

Jul 01, 2015 | 2005 Chrysler Town & Country

2 Answers

We just purchased a 2005 Chrysler Town & Country, and the wiper blades are out of sync and keep hitting. Is there some type of adjustment that can be made myself, or does this have to be done at the...


I assume it is out of warranty. Find a similar vehicle in a parking or used car lot and take a picture of its wipers assuming they are in the rest/off position. Then making sure your wiper switch is in the off position, remove the little caps at the base of the arms. Remove the nuts and gently lift the arms up and away from the vehicle, some rocking motion may be needed but do not pry on the glass. Spray some lithium grease on the little stub. Put the wiper arms back on as your picture shows them to be and snug down the nuts.

I am assuming there that someone pulled the arms off and put them back on wrong. If this does not fix the problem what you have there is that someone replaced the wiper motor and did not put the wiper transmission in the stop or rest position when he installed the new motor. So then you are going to have to get the wiper transmission out of the vehicle which could be a dealer task. You can get a repair manual on ebay or search on www.youtube.com for someone's video of this process. Some can be done by owners, some require shops. If your blades are slapping around loose, perhaps the splines or serrations in the base of the arm are stripped and some replacement arms from a junkyard are in order. Take your old arms to the junkyard so they can find exact replacements and make sure they do not sell you another stripped set. This is generally caused by turning the wipers on while they are ice glued to the glass.

Nov 25, 2010 | 2005 Chrysler Town & Country

1 Answer

We just purchased a 2005 Chrysler Town & Country, and the wiper blades are out of sync and keep hitting. Is there some type of adjustment that can be made myself, or does this have to be done at the...


Sounds like they may have been frozen, (if in cold weather) or someone grabbed an arm when they were moving and cause that. Let wipers go to park position and observe which one is sticking up further, or perhaps one is down too far, and that should tell you which one to remove and re-position.
If that doesn't tell you, turn them on and see which one doesn't seem to go far enough over on swipe.
Lift cap at pivot point ( drive end) by windshield and remove nut, and pry slightly to pop arm off, then re-position and tighten nut. If unsure, a local mechanic shop should be able to do it in about 10 minutes max.

Nov 25, 2010 | 2005 Chrysler Town & Country

1 Answer

Winshield wiper motor does not work


Remove wiper arms,open hood and remove plastic cowl(cover) at windshield,it is held in with plastic clips,the wiper motor is under the cover held in with 4 bolts(10mm).reinstall everything and turn on motor without wiper arms ,then turn it off so it finds its off position-reinstall wiper arms

Apr 15, 2010 | 2005 Mitsubishi Lancer

1 Answer

How do i get the rear wiper arm off a 2000 chrysler town n country...im replacing the motor


Look at the wiper arm. Where the shaft comes through there is a cap on the arm. Pop it up and you will see a nut remove nut and you should be able to get arm off.
Hope that helps!

Mar 06, 2010 | 2000 Chrysler Town & Country

1 Answer

How to remove rear wiper arm from 2005 mazda


if there is a nut in the middle at the base of the arm remove the nut if there is no nut then lift the wiper arm away from the window and you will see a small tab that will pull away from the base of the arm pull this away and hold it while you let the wiper back down the wiper will hold the arm up and lock the tab out now gently pry or pull the arm off

Jan 11, 2010 | 2005 Mazda 6

1 Answer

Front windshield wipers are crashing into each other


Yes you can adjust them yourself. First you need to check that the wiper arms are not bent. If not, remove the cap at the wiper arm base, under it u will find a nut, remove this nut. you should now be able to remove the wiper arm. (it is comon for caravan wiper arms to be corroded on. If the arm dosen't come off, you may need to heat up the wiper arm with a propane torch. be careful not to melt the plastic cowel under the arm. OR you can use a wiper puller or a battery puller. do not force it, you can break the arm, DO NOT PRY AGAINST THE COWEL OR WINDSHIELD.
Once both arms are off, turn your van on and turn the wipers on. watch the wiper posts, turn the wipers off and watch the wiper posts return and stop in the "parked" position. Turn the van off. Install the passanger wiper arm first, it is positioned closest to the bottom an inch or two above the black cowel. It should be parrallel to the cowel. next install the drivers side wiper arm. it is positioned about 4 inches above the passanger wiper. again running parrallel to the cowel and passanger wiper. tighten the lock nuts down (do not over tighten) wet down your windshield with glass cleaner or windshield washer fluid and test wipers. If they still hit you can lower the passanger one a little or raise the drivers one a little (careful you don't raise the drivers one too much or it will 'jump' off the windshield at the top of the wipe).
good luck, hope this helps.

Nov 23, 2009 | 2001 Chrysler Town & Country

1 Answer

Removing windshield wiper assembly ford excursion


Wiper Pivot Arm Removal and Installation
  1. Lift the windshield wiper pivot arm to the full upright position.
  1. Remove the windshield wiper pivot arm.
    1. Release the locking tab.
    1. Remove the windshield wiper pivot arm.
52fed05.gif
  1. NOTE: During installation, it is necessary to pull the locking tab out to its full open (unlatched) position and hold while assembling the pivot arm onto the mounting arm and pivot shaft. Align the key on the pivot arm head with the keyway on the shafts. This will make sure the pivot arm is correctly aligned. If necessary, the key can be removed. To adjust wiper pivot arms, refer to Wiper Blade and Pivot Arm Adjustment in this section.
    To install, reverse the removal procedure.

Jul 02, 2009 | 2005 Ford Excursion

1 Answer

No instructions on how to remove rear wiper blade on 2004 Town & Country touring. The wiper arm only raises about three inches from window, and there is no indication of a normal wiper removal at that...


there is a plastic cap where the arm connects to a post. pop this cap off with your finger nail or small screw driver. this cap hides a nut. remove the nut (10mm socket needed?) and pull the arm off to replace the blade

May 16, 2009 | 2004 Chrysler Town & Country

1 Answer

HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?


Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Jan 29, 2009 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...