Question about 2004 Nissan Quest

1 Answer

My wiper blade fuse is blown in my 2004 nissan quest. how do i access the fuse box and where is it located?  Which fuse is the wiper fuse?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 4 Answers

Just get under the hood it is problble by the battery and that is it.

Posted on Dec 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for the windshield wipers on 2004 Nissan maxima


Some cars have these included with accessories. If your other accessories work, then your windshield wiper motor requires replacement. Otherwise, read the inside cover of the fuse box the symbol for windshield wipers looks like a windscreen with two wiper blades on it.

Feb 23, 2015 | 2004 Nissan Maxima

1 Answer

Wipers wont work fuse good


sounds like the wire motor

Feb 09, 2013 | 2002 Nissan Quest

1 Answer

Help stuck n storm..where is fusebox 2004 murano windshieldwipers


There's no need to remove the fuse to change wiper blades.
If there are electrical problems the fuse locations are driver's bottom left near steering wheel, and under the hood. Under the hood is the ipdm located on the passenger side near the alternator. More fuses can be found beside the battery.
If your wiper motor runs but wipers don't move, the linkage is disconnected.

Feb 06, 2010 | 2004 Nissan Murano

2 Answers

How do I remove front wiper blades to replace with new ones on my 2006 nissan quest


How to Replace Wiper Blades Guide:
Potential tools needed to replace wiper blades:
  • Flat blade screwdriver (small)
  • Small nosed pliers
  • Latex or vinyl gloves
  • Safety goggles
To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.
  • Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
  • Step 2: Locate the mounting clips at the top pivot on the wiper blade
  • Step 3: Release the clip and remove the wiper arm
  • Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
  • Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:
  • Make sure the wiper blades are the same size as the original blades.
  • When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
  • Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
  • Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

Sep 14, 2009 | 2006 Nissan Quest

1 Answer

How to take off tire pressure light off on nissan quest 2004


remove the tire pressure light fuse from fuse-box....this should work

Jul 23, 2009 | 2004 Nissan Quest

1 Answer

2004 Nissan Maxima wiper problem


Karen...

There might be a fuse with more than just the wipers on it. Does anything else not work? A blown fuse is most likely the cause, it might be hard to locate check owners manuel for fuse locations as they can be in several locations.
Denny

Jul 07, 2009 | 2004 Nissan Maxima

1 Answer

Room lights not working.


courtesy of the Nissan Quest owners manual

"ENGINE COMPARTMENT
CAUTION
Never use a fuse of a higher or lower
amperage rating than specified on the
fuse box cover. This could damage the
electrical system or cause a fire.
If any electrical equipment does not come on,
check for an open fuse.
1. Be sure the ignition switch and the headlight
switch are OFF.
2. Open the engine hood.
3. Remove the fuse box cover by pushing the
tab and lifting the cover up.
4. Locate the blown fuse. or look on fuse box cover to see what each fuse does.
5. Remove the fuse with the fuse puller. The
fuse puller is located in the center of the fuse
block in the passenger compartment."
Replace fuse.

Oct 23, 2008 | 2004 Nissan Quest

1 Answer

Nissan Quest 2004 Tail Lights


Robynumber1,

Thanks for the email back. The nissan quest tail lights werenot operating, but the break lights were working. This was ultimately caused by a blown fuse. The fuse was blown by loose trailer lighting wires dragging on the ground, thus shorting. Problem fixed.

Aug 17, 2008 | 2004 Nissan Quest

Not finding what you are looking for?
2004 Nissan Quest Logo

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...