Question about 1989 Mercury Cougar

1 Answer

P/s pump how do I get the pulley off the pump so I can replace the water pump? p/s pump bracket covers water pump studs.Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

If the pulley is pressed on you need a special tool to remove it and to press it back on. Check with your local parts house to see if they have the tool.

Posted on Dec 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do you replace water pump?


Assuming this is a 460 Ford Big Block:

REMOVAL

-Drain cooling system.
-Remove drive belts.
-Remove bolts attaching fan shroud to radiator.
-Remove fan blade from fan clutch and remove fan shroud.
-Remove fan clutch and water pump pulley from water pump.
-Remove four bolts and one nut attaching A/C compressor mounting bracket to cylinder head and water pump. Do not remove A/C compressor or power steering pump from A/C compressor mounting bracket.
-Pull A/C compressor mounting bracket forward to remove from stud on water pump.
-Remove bolt attaching generator adjusting arm to water pump. Remove four bolts attaching generator mounting bracket to cylinder head, cylinder block and water pump.
-Remove remaining water pump attaching bolts and remove water pump from engine front cover.
-Remove water pump cover from water pump. Discard water pump housing gasket and water pump cover gasket.
INSTALLATION
-Remove any gasket material from water pump cylinder front cover and separator plate mating surfaces.
-Position new water pump housing gasket and water pump cover gasket coated on both sides with Perfect Seal Sealing Compound B5A-19554-A or equivalent water-resistant sealer meeting Ford specification ESE-M4G115-A.
-Position water pump and water pump cover onto engine front cover. Install bolts and tighten to16-24 Nm (12-18 ft. lbs.).
-Install generator mounting bracket to cylinder head, cylinder block and water pump with four attaching bolts. Install generator adjusting arm to water pump with one attaching bolt. Tighten 7/16-inch bolts to 54-71 Nm (40-53 ft. lbs.) and 3/8-inch bolts to 41-54 Nm (30-40 ft. lbs.).
-Position A/C compressor mounting bracket over water pump stud and secure to cylinder head with four bolts tightened to 54-71 Nm (40-53 ft. lbs.) and secure nut to water pump to 41-54 Nm (30-40 ft. lbs.).
-Install water pump pulley and fan clutch to water pump hub with four bolts. Install fan blade to fan clutch with four bolts. Tighten water pump pulley, fan clutch hub bolts, and fan-to-fan clutch hub bolts to 16-24 Nm (12-18 ft. lbs.). Install fan shroud.
-Install drive belts.
-Fill and bleed the cooling system.
-Start the engine and check for leaks

Jan 10, 2011 | 1997 Ford F350 Crew Cab

1 Answer

Water pump needs replacing


water pump is behind the fan pulley bracket. need to take off the timming belt to get to the water pump. also need to remove the distributor covers on bothe sides. 2 boolts that hold the a/c compressor to the fan pulley bracket ,alternator,idler pulley.

Apr 17, 2010 | 1991 Lexus LS 400

1 Answer

How to replace head gasket on 1999 2.5 cyl ford ranger


Cylinder Head Removal
  1. Disconnect the battery ground cable
  2. Relieve the fuel pressure.
  3. Drain the cooling system. Disconnect the three way catalytic converter Loosen the water pump pulley bolts.
  4. Remove the drive belt.
  5. Remove the water pump pulley, fan and clutch assembly.
  6. Remove the intake manifolds
  7. Remove the ignition wires from the spark plugs .
  8. Remove the spark plugs; .
  9. Remove the oil level indicator tube
    • Remove the bolt.
    • Remove the oil level indicator tube.
    • Remove the EGR valve to exhaust manifold tube
    1. Remove the valve cover
    1. Remove the drive belt .
    1. Recover the A/C refrigerant; refer to Disconnect the engine control wiring from the A/C compressor
    2. Remove the A/C compressor mounting bracket (2882) with the power steering pump (3A674) attached and position out of the way.
    3. Disconnect the engine control sensor wiring connector from the generator
    4. Disconnect the (1) lower radiator hose and the (2) water pump inlet tube
    5. Remove the upper radiator hose
    6. Remove the water pump inlet tube.
      • Remove the bolts.
      • Remove the water pump inlet tube.
    7. Remove the generator.
      • Remove the bolts.
      • Remove the generator.
    8. Remove the generator mounting bracket.
      • Remove the bolts.
      • Remove the bracket.
      1. Remove the ignition wire and bracket; refer to Section 303-07A .
      1. Remove the outer timing belt cover; refer to the procedure in this section.
      1. Remove the timing chain/belt (6268); refer to Timing Drive Components—Timing Belt in this section.
      1. Remove the exhaust manifold (9430); refer to Exhaust Manifold in this section.
      1. Remove the cylinder head .
        • Remove the bolts and discard. (should get new ones)
        • Remove the cylinder head.
        • Remove the head gasket and discard.
Installation
  1. Clean all gasket mating surfaces.
  1. Install new gaskets as necessary.
    • Use new cylinder head bolts.
  1. Follow the removal procedure in reverse order.
  1. Tighten the bolts in sequence, in three stages, to 70 Nm (51 lb/ft).
    • Stage 1: Tighten all bolts to 70 Nm.
    • Stage 2: Retighten all bolts to 70 Nm.
    • Stage 3: Tighten all bolts an additional 90-100 degrees.
  2. Install generator bracket. Install bolts in four stages.
    • Stage 1: Hand-start bolt 1.
    • Stage 2: Install and tighten bolt 2.
    • Stage 3: Install and tighten bolt 3.
    • Stage 4: Tighten bolt 1.
  3. Install the A/C compressor mounting bracket. Install the bolts and the stud.
    • Tighten the M10 bolts and stud to 48 Nm (35 lb/ft).
    • Tighten the M8 bolt to 25 Nm (18 lb/ft).

Mar 10, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How to install 2001 mercury villager water pump


go here and see the files section for porcedures. Change timing belt at same time. You are already there. This is a one day job.

http://groups.yahoo.com/group/villagerquest/


SECTION 303-03: Engine Cooling 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Water Pump Removal
  1. Drain the engine cooling system. Refer to Cooling System Draining, Filling And Bleeding .
  1. Remove the crankshaft pulley. Refer to Section 303-01 .
  1. Remove the water pump pulley.
    1. Remove the bolts.
    1. Remove the water pump pulley.
  1. Remove the six lower timing belt cover bolts.
  1. Lower the vehicle.
  1. Remove the upper radiator hose.
    1. Remove the bolt.
    1. Release the clamps.
    1. Remove the upper radiator hose.
  1. Remove the coolant bypass hose.
    1. Release the clamps.
    1. Remove the coolant bypass hose.
  1. Remove the A/C compressor idler pulley and bracket.
    1. Remove the bolts.
    1. Remove the A/C compressor idler pulley and bracket.
  1. Position the wire harness aside.
    1. Unclip the wire harness.
    1. Position the wire harness aside.
  1. Disconnect the vacuum reservoir vacuum hose.
  1. Unclip and reposition the main wire harness.
  1. Unclip the wire harness and position aside.
  1. Position the wire harness bracket aside.
    1. Unclip the spark plug wire from the bracket.
    1. Remove the bolt.
    1. Position the wire harness bracket aside.
  1. Remove the PCV breather hoses and tube.
    1. Release the clamps.
    1. Remove the bolt.
    1. Remove the PCV breather hoses and tube.
  1. Remove the upper and lower timing belt covers.
    1. Remove the seven upper timing belt cover bolts.
    1. Remove the upper and lower timing belt covers.
  1. NOTE: Note the location of the stud upon removal.
    Remove the water pump.
    1. Remove the six bolts.
    1. Remove the water pump.
Installation
  1. NOTE: Apply a 2.0-3.0mm (0.079-0.118 inch) bead of Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford Specification WSK-M2G343-A4 to the mounting surface of the water pump.

Dec 23, 2009 | 2001 Mercury Villager

2 Answers

Do I have to remove the whole power steering to install water pump?


I think on that model you have to remove the power steering pump pulley first before you can get to the rest of the power steering pump mounting bolts.
You can rent a special puller / installer from one from your local auto parts store.
Once you have pulled the pulley and removed the pump mounting bolts,just drop the whole pump unit with the hoses attached out of the way of the water pump.
Good Luck.

Nov 15, 2009 | 1990 Ford F150

1 Answer

I broke timing belt when replacing hormonic balancer


Here are some. Hope it helps =D

Timing Marks

Diagram


TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Jun 28, 2009 | 1992 Honda Accord

1 Answer

1999 Buick Park Avenue Water Pump Removal


Hi once you have all the bolts off for the mount raise the front of the motor up till you can remove the center part of the mount
I use a floor jack and a 2x4 across the oil pan then remove the studs for the motor mount bracket now remove the bracket and now you can get the water pump out
hope this helps

May 10, 2009 | 1999 Buick Park Avenue

2 Answers

1999 Buick Park Avenue water pump removal


that is not an idler pully that is the power steering pully if you feel through the holes in the pully you will feel the 13 mm head bolts that hold the pump to the block remove those bolts the pump will drop down and you can then remove the water pump also you have to remove the studs using the inverted torx end on the stud to unscrew it then the mount will come out

May 10, 2009 | 1991 Buick Park Avenue

1 Answer

1999 Park Avenue water pump removal


if thats got the 3800 or 3100 in it your taking out the wrong bolts!!!!!!!
your trying too remove the whole housing
you dont need too do that !!!
take off the 4- 10 mm bolts on the waterpump pully,then remove the bolts behind it i belive that there are 8 of them that takes the pump from the housing!!

May 10, 2009 | 1991 Buick Park Avenue

1 Answer

Install water pump


5.0L Engine
Removal
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the fan/clutch assembly and shroud.
  4. Loosen the water pump pulley attaching bolts.
  5. Remove the accessory drive belt.
  6. Remove the water bypass hose from the pump.
  7. Disconnect the heater hose at the pump.
  8. Remove the engine control sensor wiring harness brackets and position the harness out of the way.
  9. Remove the water pump pulley.
  10. Remove all of the water pump attaching bolts. Pay attention to the locations of any stud bolts.
  11. Pull the water pump away from the front cover, then disconnect the lower radiator hose from the pump
  12. Lift the water pump from the vehicle.
    To install:
  13. Clean the mounting surfaces of the pump and front cover thoroughly. Remove all traces of gasket material.
  14. Apply adhesive gasket sealer to both sides of a new gasket and place the gasket on the pump.
  15. Install the lower radiator hose to the water pump.
  16. Position the pump on the cover and install the bolts finger-tight. When all bolts are in place, torque them to 15-21 ft. lbs. (20-28 Nm).
  17. Position the engine control sensor wiring harness and install the retaining nuts.
  18. Install the water pump pulley and its attaching bolts. Snug the bolts.
  19. Install the heater and water bypass hoses to the water pump.
  20. Lift the accessory drive belt tensioner and install the belt.
  21. Securely tighten the water pump pulley attaching bolts.
  22. Install the engine fan/clutch assembly and the shroud.
  23. Refill and bleed the cooling system.
  24. Connect the negative battery cable, start the engine and check for leaks.

Mar 14, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...