Question about 1999 Chevrolet Cavalier

1 Answer

Tightening head i need the torque specs for tightening the head bolts for a 1999 chev cavalier 2.2L engine

Posted by on

  • Anonymous Mar 28, 2014

    need to know the torque spec Mitchell does not show

  • Anonymous Mar 30, 2014

    what are the torque specs for the bolts on the cylinder heads on a 2001 chev s10 blazer 4wd

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 916 Answers

New Headbolts are recommended

Long bolts are torqued to 46'lbs + 90 degrees.

Short bolts are torqued 43'lbs + 90 degrees.

Start in the center, and work to the edges, torquing the bolts in two stages.

Rockers are torqued to 22'lbs.

Posted on Dec 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Honda civic 1.6 engine torque specs and sequences for cylinder head


Tighten the cylinder head bolts to their final torque specification in two steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts.
  1. Step 1: Tighten each bolt to 22 ft. lbs. (30 Nm).
  2. Step 2: Tighten each bolt to 61 ft. lbs. (85 Nm).

zjlimited_1681.jpg

Fig. Cylinder head bolt loosening sequence - 1.6L (B16A2) engines (click image for zoom)

Hope helps.

Aug 05, 2011 | 1999 Honda Civic

2 Answers

1997 cavalier head gasket replacement with a 2.2. Also need the torque specs and sequence for the head bolts


Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Nov 16, 2010 | 1997 Chevrolet Cavalier

1 Answer

I AM DOING THE HEAD GASKET ON 1999 SAAB 95 4 CYL I NEED THE TORQUE SPEC ON CYL. HEAD


Torque spec

Step 1- 44 Ft.Lbs.
Step 2- 59 Ft.Lbs.
Step 3- Tighten bolts an additional 90 degrees.

Here the head bolt's tightening sequence.

bcas1298_1.gif

Nov 11, 2010 | Saab 9 5 Cars & Trucks

1 Answer

Engine torque specs for 1996 chevy cavalier 2.2l


For 1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl the check the next Head Bolt Torque sequence...

------------ front | 8 4 1 5 9 | of | | engine | 7 3 2 6 10 | ------------

Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs
Step 2: torque all bolts an additional 90 degrees Recheck final torque in sequence

*** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Hope helps (remnember rated this).

Jul 15, 2010 | 1996 Chevrolet Cavalier

1 Answer

Torque specs /head GASKET/2001 cavalier


for the 2.2L OHV:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

for the 2.4l dohc are as follows:
(pully 9 3 1 5 7
side) 10 6 2 4 8
bolts 1-8 torqued to 65Nm (40ft/lb)
bolts 9-10 torqued to 40Nm (30ft/lb)

then (either engine) give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

May 20, 2010 | 2001 Chevrolet Cavalier

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

1 Answer

Torque and tightening sequence for 1999 2.2 chev


Cylinder Head Bolts

Step 1
Head Bolts A 46 (62)
Head Bolts B 43 (58)

Step 2 Additional 90 Degrees

Tightening Sequence:
http://www.anubiscycle.com/fixya/99cavheadsquence.png

Jan 17, 2010 | 1998 Chevrolet Cavalier

2 Answers

Head bolt torque spec


Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Aug 16, 2009 | 1999 Ford Escort

1 Answer

Replacing head


There should be 10 headbolts. This vehicle uses torque to yield headbolts and should be replaced with the new gasket. Bolts 1-8 get torqued to 40 ft lbs initially, bolts 9 and 10 get torqued to 30 ft lbs initially, Then all bolts get turned an additional 90 degrees. I would strongly suggest borrowing a torque angle gauge for doing this or you might be doing the same repair next week.

Feb 12, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
1999 Chevrolet Cavalier Logo

537 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...