Question about 1987 Nissan Pickup

1 Answer

'87 nissian pu clutch will not engage

After temp. droped to the teens for a few days and not driving the truck for two days the clutch will not engage. after putting a heat lamp on the clutch housing for 8hrs. it worked enough to move it into a shop where it was 65degr. the clutch then stoper working it stayed there for 10hrs. it has not worked since then. HELP !!!!!!!!!!

Posted by on

  • sir_loya Dec 22, 2008

    how does one flush the reservoir, and what type of fluid do i replace it with?

  • sir_loya Dec 28, 2008

    thank you Kuya Louie, now I can deliver firewood to the needy and the elderly, I could not beleave something as simple as cleanning the system would cause such a big problem



    thank you very much

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 120 Answers

Flush all the fluid from the reservoir. your fluid is contaminated

Posted on Dec 21, 2008

  • Kuya Louie Dec 22, 2008

    loosen the bleeder on your slave cylinder and you will notice the fluid will come out wait till the reservoir is empty and clean the reservoir will a clean rag, take out as much dirt as you can from the reservoir. close the bleeder and pour a new dot3 brake fluid, you can re do the flushing as much as you can to clean the system. get someone who will help you finally bleed the system, because one has to pump the pedal and the other will open and close the bleeder. you should be all set after then. good luck!

  • Kuya Louie Dec 29, 2008

    My pleasure sir!

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 chevy trailblazer cooling temp running 230


Smart man using a scanner for the actual temp. Assuming you're not losing coolant....2 things I'd look at here, 1st is you may have air in the system, make sure to purge all the air. 2nd is your fan clutch, I've replaced a few fan clutches in my own Trailblazer. Have had them bad right out of the box brand new. Have had bad brand new fan clutches on 2 of my last Trailblazers. You should hear it engaging especially in stop and go traffic.

Aug 02, 2016 | 2003 Chevrolet TrailBlazer

1 Answer

87 toyota clutch wont engage after brakes were replaced


Brake and clutch are vacumme assisted and hard to start seems like vac hose left of of has leak

Nov 14, 2012 | Toyota Cars & Trucks

1 Answer

Air conditioner not working on 1993 bonnevile, compressor not engaging, charge good, power at low pressure switch, switch is closed, need to know what turns a/c relay for compressor clutch on, clutch...


the ECM supplies the ground circuit for the a/c clutch. the high pressure switch also needs to be closed to engage the clutch. when the low pressure switch and the high pressure switch are closed that completes the power circuit to trigger the relay.then the power on the #30 terminal can connect to the #87 terminal to send power to the a/c clutch.

Aug 02, 2011 | Pontiac Bonneville Cars & Trucks

1 Answer

2000 Chevy Silverado normal operating temp is 210 , recently temp rises to 250. Its been this way for a few days, common operating temp is around 240-250 now, but does not overheat. Coolant levels are...


250 TOO HOT FOR ENGINE AND TRANSMISSION. SOUND LIKE COOLING FAN CLUTCH BAD ITS FREEWHEELING NOT LOCKING UP TO DIRECT DRIVE TOO COOL ENGINE OFF BECAUSE THE FAN CLUTCH THERMOSTAT NOT WORKING THE HOT SILICONE OIL CAUSE IT TO EXPAND TO PUT RESISTANCE ON CLUTCH TO PUT DRAG ON FAN CLUTCH CAUSING IT TO LOCK IN GIVE IT DIRECT DRIVE.I WOULD STILL REPLACE THERMOSTAT AND RADIATOR PRESSURE CAP IF TEMPERATURE STILL 250 DEGREES YOUR RADIATOR AND COOLANT SYSTEM NEED FLUSHING.

Aug 17, 2010 | 2000 Chevrolet Silverado

1 Answer

87 Silverado PU Fuel gauge moves to center &


should start checking for a grounded wire.

May 24, 2010 | 1983 Chevrolet Silverado

1 Answer

I am having to push my clutch completely to floor to get the clutch to engage. I have about 1 inch of play. What should I check first. 95 Nissan PU King


Under the hood you will find the clutch fluid reservoir check that for low fluid. It's possible you have a minor leak on the slave cylinder.

Nov 14, 2009 | 1995 Nissan Pickup

1 Answer

87 300ZX STARTER WILL NOT ENGAUGE. I HAVE CHECKED THE CLUTCH SWITCH AND IT IS WORKING


The starter has a thing called a starter drive. It operates with a over running clutch that is a safety that keeps it from over speeding when still engaged with a started engine. That drive needs replaced, the clutch is bad.

Jul 07, 2009 | 1987 Nissan 300ZX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...