Question about 1996 Toyota 4Runner

1 Answer

Key won't turn on in 96 4runner

The key will not turn past the acc.

Posted by on

  • balimaka mpembe May 11, 2010

    bad ignition suitch or trhotle in the gear position

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 68 Answers

Stearing wheel in locked postion?

Posted on Dec 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

92 camry. When turn key to shut off engine the key will not go past the ACC pos. Will not go to LOCK pos to remove the key. Have to disconnect the battery to turn key to LOCK pos. What is the fix?


Park shift interlock. A safety device that will only allow the key to be removed when vehicle is in park. It is malfunctioning could be as simple as a cable sticking

Feb 11, 2017 | Toyota Camry Cars & Trucks

1 Answer

Place key in ign. And turns with no clicks btw off acc and start. When you turn off, goes past off to acc no clicks


Hello Ron, If your car does not crank when you turn the key, it sounds as if you have problems with the ignition switch . Or the actuating rod is disconnected.

Apr 10, 2015 | 1998 Buick Park Avenue

1 Answer

When you turn the key,it only goes to the Acc position


Turn the Key OVER and see if you can rotate it then.

Are your Wheels turned HARD and the Steering Wheel Locked?
Are your Wheels against a CURB and not allowing the Steering Wheel to rotate to remove the Locking Mechanism to go freely?

Feb 13, 2014 | Lexus LS 400 Cars & Trucks

1 Answer

2004 saturn Ion ignition key will not turn smoothy. I have to wiggle my key and then it will turn. On a few occations the key wont turn backwards past ACC. When it was in the ACC position I could...


Try puffing some powder graphite into the key slot and inserting and removing the key several times. The tumbler pins get dry and jam in the holes and will not move so the graphite is the recommended lubricant for locks. Be careful as it leaves black residue that has to be cleaned with a wet clean rag.

Sep 14, 2013 | Saturn Cars & Trucks

1 Answer

Why does my 2005 chevrolet classic theft system keep coming on and then the car won't start afterwards unless reset by turning the key to ACC for 10 minutes then the car starts?


If you have a spare set of keys try using the different key. The identity chip in your key may be shorting.

Otherwise the "Reader" in your ignition switch may be cutting out. This puts it into an activation loop.

Nov 08, 2012 | Cars & Trucks

2 Answers

2006 Chev Cobalt won't crank...no lights, no sounds nothing. When tried to get the key out it won't go past the ACC position? Any ideas on the problem?


Is the battery dead? Check your battery condition and connections. Check your starter fuse from there. Check the connection to the starter then progress to the ignition side of the concern

Sep 10, 2012 | 2006 Chevrolet Cobalt

1 Answer

How do I remove the ignition lock on my 1998 Mazda Protege? Tumblers are stuck. Key won't go past accessory.


if ou do not have the key, look at the replacement lock there'll be a tab which recesses when the key is turned to acc or on position. It is that tab which prevents you from removing lock cylinder it has to be forced into a recessed position or drilled to where the cylinder can removed. If u do then locate tab turn key to acc or on and push tab to recessed position and remove cylinder.

May 31, 2012 | 1998 Mazda Protege

1 Answer

Key wont move ignition switch past ACC to start position. Purchased new key and still doesn't work.


The actual ignition switch, the electrical switch which the key cylinder turns, is probably bad. It is made of plastic and does eventually wear out. Have that part checked out.

Jan 04, 2011 | Toyota 4Runner Cars & Trucks

Not finding what you are looking for?
1996 Toyota 4Runner Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...