Question about 1987 Toyota 4Runner

2 Answers

I put a new rotor on my truck and then it wobbles.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

Wrunner is right! Make sure you do this IMMEDIATELY. Remove the hub(if 4wd) pull snap ring, get a Chiltons or Haynes manual and tighten the adjusting nut to factory ft. lbs. DO NOT drive like this....you will burn up the bearings and rotor as well.

Posted on May 27, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 68 Answers

U didnt tightin the center nut enough careful driving

Posted on Dec 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wobble of carsteering when braking


Brake components may b worn. Inspect rotors and pads. So with the steering...git an xperiencd mech to testdrive

Apr 14, 2015 | Cars & Trucks

1 Answer

06 dodge magnum wobbles from the rear


check the run out of the axle shafts

Apr 12, 2012 | Dodge Ram 1500 Cars & Trucks

2 Answers

Front end wobbles after highway speeds and brakes/bearings are hot. Very pronounced when braking after a few minutes at highway speed. Had original rotors turned. Helped, but then had them replaced with...


I have had the same problem ever since I bought my 4runner new in 99. I've tried all kinds of tires, constant balancing, rotations, alignments, brakes, you name it, I even have a new front end now, but still have wobble in the front end. It's acts like having loose tie-rod. NoOne can figure it out. LEMON?
Mike

Jul 15, 2010 | 1999 Toyota 4Runner

2 Answers

High speed braking steering wobble


your brake rotors are most likely warped. replace them maching them only makes the problem worst

May 12, 2010 | 2001 Audi A4

1 Answer

Just want to know how to put the rotors on the car.


If your rotors (new ones) came as just the rotor with no center hub, just remove the brake caliper, take the rotor off and put the new one back on. But, the one i think you have is a bit different...with hub attached. On that one, remove the center cover, cotter pin and nut.
Remove caliper. push on one side of the rotor and the outer bearing and washer will come out. Put the parts aside and pull on the rotor and it will come off. Put the nut back on the spindle and put the rotor on over the nut, "hook" the inner bearing on the nut as you give the rotor a quick tug (like removing it) and inner bearing will come out.
Clean and re-pack bearings and install (I recommend you replace the inner seal.) Put together in reverse order of removal, tighten nut snugly but not really tight, turn rotor while tightening. It is tight enough when there is no wobble in the rotor. that is all you need.Don't forget the cotter pin. If hole does not align, tighten do not loosen nut till hole aligns.

Apr 24, 2009 | Oldsmobile Custom Cruiser Cars & Trucks

1 Answer

95' mustang no fire


This also happened to my '95 mustang 5.0L I was actually driving when it lost power. Take the cap off of the distributor and see if the shaft wiggles. The distributor shaft in the mustangs are the weakest point of the engine. If the shaft wobbles the rotor will wobble hitting the points and may break the rotor. All the metal grinding will put little metal shavings in the housing where the magnetic pick-up will attract them, this is the problem. You can replace the magnetic pick-up but if the shaft is moving around you will need a new distributor all around.

Apr 14, 2009 | 1995 Ford Mustang

1 Answer

Brake pads and rotors glazed over?


Well .. if indeed you have glazing and you don't want to replace the rotors you can either use some emery cloth to "sand" them by hand or have them cut (if you can find an automotive or machine shop). But you should also replace the pads then

Feb 14, 2009 | 2003 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...