Compressor wont run. Low pressure side said low on gas. Put in maybe 1-2 oz gas and gauge said pressure ok. Compressor won't run. Fuse ok relay ok. no volts at compressor.
SOURCE: 99 Suburban A/C Not working
The A/C pressue switch may be bad as well. Also the mode switch on the control head inside the vehicle. There are many other exsisting problems pertaining to a/c. I suggest a manual from Auto Zone for many faults can be noted especially wiring can be at fault
SOURCE: 1991 Sierra GMC AC control problem
The follwing is a cut and paste from a service bulletin:
Bulletin No.: 461202
Date: May, 1994
SUBJECT:
A/C CONTROL HEAD FLASHES OR ERRATIC OPERATION OF A/C CONTROLS (POLISH
TERMINALS)
MODELS:
1988-94 CHEVROLET AND GMC TRUCK C/K MODELS
1990-94 CHEVROLET AND GMC TRUCK TOPKICK/KODIAK MODELS WITH C60 OR C69 AIR
CONDITIONING
CONDITION:
A/C Control Head flashes, performs erratically or malfunctions.
CAUSE:
Light surface corrosion on the Control Head terminals.
CORRECTION:
Remove the A/C Control Head and while holding the unit with the terminal
cavity down (toward the floor) so no particles will fall inside on the
circuit boards, polish the terminals on both sides of the cavity with a lead
pencil pink eraser. Do not use an ink eraser or other abrasive such as a
small wire brush or sandpaper, etc. Doing so will remove the terminal
coating and degrade the contact surface.
Performing this procedure, in many cases, will make replacing the Control
Head unnecessary. Using this procedure in conjunction with the A/C circuit
diagnosis found in the Electrical Diagnosis Manual and especially before
replacing a Control Head for any reason is recommended.
After polishing the Control Head terminals, but before reconnecting, check
for proper terminal contact as described in the applicable electrical
diagnosis manual. If contact is good, apply dielectric grease (P/N 12345579)
to the harness connector terminals. Please do not apply grease to the
Control Head.
SOURCE: 1992 gmc c1500 ac compressor relay location
I pulled this from another web site
"The AC clutch relay is located inside the cab on a metal bracket that is easiest to see when you remove the glove box compartment.
The relay is on a metal bracket bolted to the top of the plastic air box, forward and to the center of the dash from glove box.
There are three relays in a row on that bracket. The AC clutch relay is the end one closest to the driver’s side."
Testimonial: "Right on target... THANKS"
SOURCE: low oil pressure 93 GMC P/U w/350 motor w/205,000 miles gauge
While engine is running, open the cover where you add oil to engine and see if you see a good flow of oil, if good flow, could be as easy as replacing oil sending sensor. got to realize that if poor maintenance history your engine may not be building enough pressure at iddle to move your hydraulic operated valves, only when you rev it up it will pump enough to run smooth. if running engine too long, you may cause more damage to other engine components such as crankshaft and cam shaft bearings. if you can spare a few bucks, have a good mechanic check your oil pressure with a mechanical gauge. another cheap option is to replace oil pump. last resort if you love your truck as much as we do,replace engine or rebuild it. At 205,000 this is a normal symptom, other than timing chain problems, most engines don't make it that far. hope this helps!
SOURCE: LOW OIL PRESSURE ON 2007 GMC SIERRA 1500. CHANGED
have it tested using a manual gage if still low then main baring ore most likely bad that would mean a over hall if is really low and bearings bad should be making rattle noise when started up first few seconds
Testimonial: "thanks alot.truck is not making a rattling noise.we did check it with a manual gauge.it read about 10 at idol. press. gets better as you incr speed"
281 views
Usually answered in minutes!
×