Question about 1998 Oldsmobile Intrigue

1 Answer

Access light bulb

I need to know how to access the turn signal light bulb in the headlamp. I need to replace it but cannot access it.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hey inorder to acces the turn signals you have to remove the whole headlight encasement. It sounds liek a huge process but it's incredibly simple. there are 2 white clips that you can remove by pulling up on them and sliding them outward from the headlight encasement. Open the hood and theres on right in the corner and the other is on the opposit end of the headlight case.

Posted on Dec 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a trick to getting to the rear turn signal on a 2003 ford focus hatchback. I had removed the screw to the lens cover but I still cannot gain access to the turn signal bulb to replace it.


Replacing tail/brake/backup lights and turn signal bulbs (coupe)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. From inside the luggage

compartment remove the wing nut

of the rear light assembly cover.

3. Using a Phillips screw driver

remove the screw. The lamp is still

retained by a spring loaded clip.

Remove by gently pulling out the

light housing.

4. Turn the bulb socket counterclockwise as far as possible and pull it

out.

5. Pull the bulb straight out of the socket.

Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (sedan)

1. Make sure the headlamp control

is in the OFF position and then

open the trunk.

2. From inside the luggage

compartment remove the three wing

nuts of the light housing.

3. Gently pull the light housing to

the outside.

4. Turn the bulb socket

counterclockwise and pull it out.

5. Pull the bulb straight out of the socket.
Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (wagon)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. Using a screw driver remove the

fixings and trim from the body.

3. Remove the socket from the lamp

assembly

4. Pull the bulb straight out of the

socket.
Install in reverse order.


Hope this helps.

Zeppelinx12

Mar 03, 2011 | 2003 Ford Focus

1 Answer

Rear turn signal b ulb burned out - How to replace


Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif

Dec 19, 2010 | 1994 Buick Century

1 Answer

How do i remove bulb from socket for day time running light on 2002 avalanche


dak408_133.gif
  1. Open the hood.
  2. Remove the park/turn signal lamp assembly.
  3. Remove the headlamp retainer pins.
  4. Pull out the headlamp assembly in order to access the electrical connector.
  5. Disconnect the electrical connector.
  6. Remove the bulb from the headlamp assembly by twisting the bulb counterclockwise.
INSTALLATION PROCEDURE

IMPORTANT:
  • Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
  • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.
  1. Install the new bulb to the headlamp assembly by twisting the bulb clockwise in order to lock in place.
  2. Connect the electrical connector to the bulb.
  3. Install the headlamp assembly.
  4. Install the headlamp retainer pins.
  5. Rotate and lock the pins in place.
  6. Install the park/turn signal lamp assembly.
  7. Inspect the operation.

Dec 11, 2010 | 2002 Chevrolet Avalanche

1 Answer

How to change a front turn light in a 1996 taurus.


Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation
  1. Remove Headlamp (13008) as outlined.
Headlamp Assembly
Removal and Installation
  1. ani_caut.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
  1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
  1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.


    Headlamp Assembly (Taurus Shown, Sable Similar)


    k24744a.gif
  1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
  1. Remove screw from park/turn signal housing.
  1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
  1. Remove parking lamp from vehicle.
  1. To install, reverse Removal procedure.


    Front Lamp-Lamp Assembly, Taurus


    k23818a.gif

Nov 19, 2010 | Ford Taurus Cars & Trucks

1 Answer

2000 Cavalier: replacing signal bulb on 99 cavalier drivers side ...


remove the mounting screw on the lens, then remove the top 2 bolts holding the headlamp, pull headlamp out to gain access to the mounting nut on the turn signal. Remove the nut and the turn signal light will pull straight out allowing you to replace the bulb.

May 17, 2010 | 2000 Chevrolet Cavalier

1 Answer

How do i access front turn signal light bulb on 2001 camaro


  1. Open the hood.
  2. Remove the headlamp housing bracket bolt from the headlamp bracket.
  3. Pull the headlamp inboard to disengage the headlamp tabs from the headlamp bracket slots.
  4. Pull the headlamp forward to access electrical connectors.
  5. Disconnect the electrical connectors from the headlamp.
  6. Remove the headlamp from the vehicle.
Remove the park and turn signal lamp sockets from the lamp by rotating counterclockwise.

Mar 09, 2010 | 2001 Chevrolet Camaro

1 Answer

Turn signal lamp is inside of headlamp housing


you want to change the turn signal light? front yes to what ever side you need to change the access is to the back of the head light assy. Front Turn Signal Light Bulb Size: 1157A
Rear Turn Signal Light Bulb Size: 1157
check too owners manual will show you how to thanks Lee let me know how it goes thanx

Dec 26, 2009 | 2003 Ford Crown Victoria

1 Answer

Please tell me how to replace a burned out head light, high beam.


To replace the headlamp, turn signal, or parking lamp bulb:This information should be in your owner's manual.
Turn the wheel to access the wheel well.
  1. Remove the fasteners located on the wheel liner. To access the headlamp and the turn signal/parking lamp bulbs.
  2. Reach in behind the wheel well liner and locate the bulb to be changed.
  3. Turn the bulb socket counterclockwise and pull it straight out of the lamp assembly.
  4. Pull the old bulb straight out of the bulb socket.
  5. Push the new bulb straight into the bulb socket until it clicks.
  6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place.
  7. Reinstall the wheel well liner using fasteners.

Nov 11, 2009 | 2006 Chevrolet HHR

1 Answer

Front turn signal bulb replacement


HEADLAMP BULB REPLACEMENT

REMOVAL PROCEDURE

CAUTION: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:

  • Turn off the lamp switch and allow the bulb to cool before changing the bulb.
  • Leave the lamp switch OFF until the bulb change is complete.
  • Always wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • Keep dirt and moisture off the bulb.
  • Properly dispose of the used bulb.
  • Keep halogen bulbs out of the reach of children .
NOTE : Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause the bulb to explode when the bulb is turned on. If either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry.


  1. Open the hood.
  2. Remove the headlamp. Refer to Headlamp Replacement .
  1. Remove the access cover from the rear of the headlamp.
  2. Disconnect the electrical connector from the socket.
  3. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  4. Disconnect the electrical connector from the socket.
  5. Remove the bulb and socket from the headlamp.
INSTALLATION PROCEDURE

IMPORTANT :
  • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket.
  • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.
    1. Position the bulb and socket to the headlamp.
    2. Connect the electrical connector to the socket.
    3. Install the bulb and socket to the housing by rotating the bulb and socket clockwise, locking the retaining tabs to the housing.
    4. Install the access cover to the rear of the headlamp assembly
    5. Install the headlamp

REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the headlamp.
  3. Rotate the bulb and socket counter-clockwise in order to remove the bulb and socket from the housing.
  4. Remove the side marker bulb (3) or turn signal/park bulb (4) from the socket.
INSTALLATION PROCEDURE


  1. Install the side marker bulb (3) or turn signal/park bulb (4) to the socket.
  2. Wipe the bulb with a clean cloth to ensure the bulb is free of any dirt or oil.
  3. Install the bulb and socket to the headlamp by rotating the bulb and socket clockwise, locking the retaining tabs to the headlamp.
  4. Install the headlamp.

Jul 10, 2009 | 2004 Chevrolet TrailBlazer

2 Answers

Replace the front turn signal light bulb


you have to go under the front of the car. very easy to fix.

Oct 21, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1998 Oldsmobile Intrigue Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...