Question about 1998 Jaguar XK8

1 Answer

Windshield wiper does not work. Motor and fuse good. Wiper switch good. If jump from fuse panel to wiper motor and it works.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 64 Answers

Hi!You need to check the wiring circuit to the motor.It could be that there is a breaken wire.

Posted on Dec 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

2 Answers

My wiper motor only works on high and stops were ever the wipers are at. And the washer motor doest #39;t work


Low Speed Windshield Wipers
Low speed is activated when the multifunction switch supplies a specific ground to the speed inputs of the windshield wiper motor module. The windshield wiper motor module then supplies ground to only the windshield wiper run/park relay coil, activating it. When the windshield wiper run/park relay is activated, the deactivated high/low relay connects voltage to the windshield wiper motor low input activating the wiper motor. The windshield wiper motor module continues to operate the windshield wiper motor in the same manner as in high speed, but in low speed with the wiper motor connected to the low speed input.
Washer System
The windshield washer is activated by the internal wiper motor module when it receives a ground signal input from the multifunction switch. Dependent on the switch selection, the internal wiper motor module activates the windshield washer relay (internal) by grounding the respective relay coil. When the relay is activated, it connects voltage to the washer pump while the washer level switch provides ground to the washer pump.
Visual Inspection Chart Mechanical Electrical
  • Windshield washer hoses
  • Wiper linkage
  • Multifunction switch
  • Battery junction box (BJB) fuse 110 (30A)
  • Central junction box (CJB) fuse 13 (10A)
  • Circuitry
  • Windshield wiper motor
Symptom Chart Condition Possible Sources Action
  • The wipers are inoperative
  • Fuse(s)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test A .
  • The wipers stay on continuously
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test B .
  • The high/low wiper speeds do not operate correctly (intermittent wiper mode OK)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test C .
  • The intermittent windshield wiper speed does not operate correctly (high/low speeds OK)
  • Circuitry
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test D .
  • The wipers will not park at correct position
  • Pivot arm adjustment
  • Linkage
  • Windshield wiper motor
  • REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section.
  • The washer pump is inoperative
  • Circuitry
  • Windshield washer pump
  • Multifunction switch
  • Windshield wiper motor
  • Go To Pinpoint Test E .
Do you know how to do electrical testing ?
  • windshield wiper motor
  • PINPOINT TEST C: THE HIGH/LOW WIPER SPEEDS DO NOT OPERATE CORRECTLY (INTERMITTENT WIPER MODE OK) s6a~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
    Test Step Result / Action to Take C1 CHECK THE MULTIFUNCTION SWITCH
    • Key in OFF position.
    • Disconnect: Multifunction Switch C202b.
    • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
    • Does the multifunction switch pass the component test?
    Yes
    GO to C2 .

    No
    INSTALL a new multifunction switch. REFER to Section 211-05 . C2 CHECK CIRCUIT 57 (BK) FOR AN OPEN
    • Measure the resistance between the multifunction switch C202b-5, circuit 57 (BK), harness side and ground.
      s6a~tr~en~file=n0025872.gif~gen~ref.gif
    • Is the resistance less than 5 ohms?
    Yes
    GO to C3 .

    No
    REPAIR the circuit. TEST the system for normal operation. C3 CHECK CIRCUITS 56 (DB/OG), 61 (YE/RD), AND 63 (RD) FOR OPENS
    • Disconnect: Windshield Wiper Motor C125.
    • Using the following table, measure the resistance between the multifunction switch C202b harness side and the windshield wiper motor C125 harness side:

      Multifunction Switch C202b Windshield Wiper Motor C125 pin 6, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 1, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 4, circuit 63 (RD) pin 9, circuit 63 (RD)

      s6a~tr~en~file=n0025874.gif~gen~ref.gif
    • Are the resistances less than 5 ohms?
    Yes
    GO to C4 .

    No
    REPAIR the circuit. TEST the system for normal operation. C4 CHECK FOR CORRECT WIPER MOTOR OPERATION
    • Disconnect all wiper motor connectors.
    • Check for:
      • corrosion
      • pushed-out pins
    • Connect all wiper motor connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present?
    Yes
    GO to C5 .

    No
    The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. TEST the system for normal operation. C5 CHECK THE WINDSHIELD WIPER MOTOR
    • Key in OFF position.
    • Disconnect: Windshield Wiper Motor C125.
    • Carry out the windshield wiper motor component test as outlined in this section.
    • Does the windshield wiper motor pass the component test?
    Yes
    The system is operating correctly at this time. The concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

    No
    INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

    Jul 20, 2016 | 2006 Mercury Grand Marquis

    2 Answers

    I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


    The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
    The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
    Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
    Visual Inspection Chart Mechanical Electrical
    • Windshield washer pump hoses
    • Windshield wiper mounting arm and pivot shaft
    • Bussed electrical center (BEC) fuse 10 (30A)
    • Smart junction box (SJB) fuse 3 (10A)
    • Circuitry
    • Windshield wiper motor
    • Windshield washer pump
    • Windshield wiper/washer switch
    • The wipers stay on continuously
    • Circuitry
    • Windshield wiper motor
    • Windshield wiper/washer switch
    • Go To Pinpoint Test C .
    PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
    Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
    • Key in OFF position.
    • Disconnect: Windshield Wiper/Washer Switch C2137.
    • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
    • Does the windshield wiper/washer switch pass the component test?
    Yes
    GO to C2 .

    No
    INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
    • Disconnect: Windshield Wiper Motor C125.
    • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

      Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

      s6b~tr~en~file=n0011980.gif~gen~ref.gif
    • Are the resistances greater than 10,000 ohms?
    Yes
    GO to C3 .

    No
    REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
    • Disconnect all the windshield wiper motor connectors.
    • Check for:
      • corrosion.
      • pushed-out pins.
    • Connect all the windshield wiper motor connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present?
    Yes
    INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

    No
    The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
    You

    Feb 20, 2015 | 2007 Ford Mustang Coupe

    2 Answers

    Where is the fuse box for the wipers


    It is under the dash panel right hand side , kick panel ? Fuse F1.1 10amp . an fuse F1.113 30 amp.
    Visual Inspection Chart Mechanical Electrical
    • Windshield washer hoses
    • Wiper linkage
    • Multifunction switch
    • CJB fuses:
      • 1 (10A)
      • 38 (25A)
      • 113 (30A)
    • Circuitry
    • Windshield wiper motor
    • The windshield wipers are inoperative
    • Multifunction switch.
    • Circuitry.
    • Ignition switch.
    • Windshield wiper motor.
    • Go To Pinpoint Test A .
    PINPOINT TEST A: THE WINDSHIELD WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 1002 (BK/PK) FOR VOLTAGE
    • Key in OFF position.
    • Disconnect: Windshield Wiper Motor C125.
    • Key in ON position.
    • Measure the voltage between windshield wiper C125 pin 5, circuit 65 (DG), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 1002 (BK/PK), harness side and ground.
      s3j~tr~en~file=a0039065.gif~gen~ref.gif
    • Are the voltages greater than 10 volts?
    Yes
    GO to A2 .

    No
    REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 875 (BK/LB) FOR OPENS
    • Key in OFF position.
    • Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 875 (BK/LB), harness side and ground.
      s3j~tr~en~file=a0037610.gif~gen~ref.gif
    • Are the resistances less than 5 ohms?
    Yes
    GO to A3 .

    No
    REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH
    • Disconnect: Multifunction Switch C202a.
    • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
    • Did the multifunction switch pass the component test?
    Yes
    GO to A4 .

    No
    INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR OPEN
    • Measure the resistance between C202a pin 4, circuit 57 (BK), harness side and ground.
      s3j~tr~en~file=a0045222.gif~gen~ref.gif
    • Is the resistance less than 5 ohms?
    Yes
    GO to A5 .

    No
    REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS
    • Using the following table, measure the resistance between the multifunction switch C202a harness side and the windshield wiper motor C125 harness side:

      Multifunction Switch C202a Windshield Wiper Motor C125 pin 7, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 5, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 1, circuit 63 (RD) pin 9, circuit 63 (RD)

      s3j~tr~en~file=a0045221.gif~gen~ref.gif
    • Is the resistance less than 5 ohms?
    Yes
    GO to A6 .

    No
    REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION
    • Disconnect all wiper motor connectors.
    • Check for:
      • corrosion
      • pushed-out pins
    • Connect all wiper motor connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present?
    Yes
    GO to A7 .

    No
    The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR
    • Key in OFF position.
    • Disconnect: Windshield Wiper Motor C125.
    • Carry out the windshield wiper motor component test as described in this section.
    • Did the windshield wiper motor pass the component test?
    Yes
    The system is operating correctly at this time. Concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

    No
    INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section. Hope this helps !

    Feb 16, 2015 | 2002 Ford Expedition

    2 Answers

    How do you replace windshield wiper motor on a 1997 ford e250 van


    REMOVAL
    1. Raise and support the hood.
    2. Remove the windshield wiper pivot arms.
    3. Remove the cowl top vent panels.

    25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
    1. Disconnect the windshield wiper mounting arm and pivot shaft.
    1. Remove the access cover from the dash panel.
    2. Remove the mounting arm and pivot shaft retaining clip.
    3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

    25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
    1. Remove the windshield wiper motor.
    1. Disconnect the electrical connector.
    2. Remove the three bolts.
    3. Remove the windshield wiper motor.
    INSTALLATION

    25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
    1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

    25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
    1. Install the windshield wiper motor.
    1. Place the windshield wiper motor in the dash panel.
    2. Install the three retaining bolts.
    3. Reconnect the electrical connector.

    25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
    1. Reconnect the windshield wiper mounting arm and pivot shaft.
    1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
    2. Install the access cover in the dash panel.
    1. Install the cowl top vent panels.
    2. Install the windshield wiper pivot arms.
    3. Adjust the windshield wiper pivot arms.
    This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

    Nov 17, 2014 | Cars & Trucks

    2 Answers

    2000 toyota camry windshield wipers won't work


    First I would look in the fuse box by the driver side and check the fuse,if good then get a meter and see if power is going to wiper motor,if so,then wiper motor is bad,if no power is going to motor,then bad switch,here's a link to see. Repair Guides Windshield Wipers And Washers Windshield Wiper Motor...

    Windshield Wiper Switch

    Print
    REMOVAL & INSTALLATION
    The windshield wiper/washer switch is part of the Combination Switch Assembly. Refer to Turn Signal/Combination Switch services procedures.

    Oct 18, 2014 | 2000 Toyota Camry

    2 Answers

    My 2001 mustang cobra windshield wipers wont work


    Did you ever fix this problem I have a 03 mustang cobra same problem Please help

    Feb 05, 2012 | 2001 Ford Mustang

    2 Answers

    Wipers


    To troubleshoot car windshield wiper problems, you need to thoroughly investigate problems with any of its operating parts. Here are some of the things that you need to check to determine why are your car windshield wipers not working.

    Check Wiper Motor
    The wiper motor is the driving force of the windshield wiper. Feel the motor and listen to a humming sound. If there is no humming, the motor is the problem. Check if the motor is working properly and see to it that its electrical connections are made properly. If you find that the motor is dead and beyond repair, get it replaced immediately.

    Check For Break in Connecting Wires
    The connecting wires of the motor sometimes go loose and that may cause the windshield wipers to stop working. Also check the battery plug connection which the motor has. Connecting the loose wires properly or fixing/replacing the plug might solve your problem.

    Check Wiper Switch
    Another wiper assembly part that can malfunction is the wiper switch itself. Check for switch malfunction and if you find that is indeed the problem, get it replaced from a mechanic.

    Check for Bent Wiper Arms
    Bent wiper arms can cause the operation of the wipers to be hampered. If the wiper arms are bent beyond repair, get them replaced immediately.

    Check For Blown Out Car Fuse
    A blown up car fuse could be the culprit that has stopped the windshield wipers from working. Check the fuse assembly under the dashboard of the car. Replacing a blown fuse might fix the problem of windshield wipers not working.

    Windshield Wiper Sprayers Not Working - Things to Check

    Sometimes the windshield wiper sprayer stops working which can be very annoying. The washer mechanism is a self cleaning mechanism for the windshield. Here are some of the things that you need to check in case it is not working.

    Check Windshield Washer Motor
    The windshield washer mechanism might have been impaired due to the malfunctioning of the wiper washer motor. Check if its working and get it replaced if it is beyond repair.

    Check Windshield Washer Fluid Level
    Sometimes the washer doesn't work because the washer fluid levels are not filled to requisite levels. Filling in fluid might restore normal functioning.

    Check For Broken Washer Hose
    The connecting washer hose that connects the reservoir to the nozzle, might be broken or worn out stalling the overall operation. Check the hose for leaks and get it replaced.

    Check Washer Nozzle For Clogging
    Last thing to check is the nozzle of the washer for clogging. An obstruction in the washer nozzle might be the reason for windshield wiper sprayers not working. Using a pin, clean the clogged nozzle. This might restore the sprayer to the normal working condition.

    Jan 28, 2011 | 2005 Scion xA

    2 Answers

    Wiper stopped working...what is the problem


    Wipers Not Working - Things to Check

    To troubleshoot car windshield wiper problems, you need to thoroughly investigate problems with any of its operating parts. Here are some of the things that you need to check to determine why are your car windshield wipers not working.

    Check Wiper Motor
    The wiper motor is the driving force of the windshield wiper. Feel the motor and listen to a humming sound. If there is no humming, the motor is the problem. Check if the motor is working properly and see to it that its electrical connections are made properly. If you find that the motor is dead and beyond repair, get it replaced immediately.

    Check For Break in Connecting Wires
    The connecting wires of the motor sometimes go loose and that may cause the windshield wipers to stop working. Also check the battery plug connection which the motor has. Connecting the loose wires properly or fixing/replacing the plug might solve your problem.

    Check Wiper Switch
    Another wiper assembly part that can malfunction is the wiper switch itself. Check for switch malfunction and if you find that is indeed the problem, get it replaced from a mechanic.

    Check for Bent Wiper Arms
    Bent wiper arms can cause the operation of the wipers to be hampered. If the wiper arms are bent beyond repair, get them replaced immediately.

    Check For Blown Out Car Fuse
    A blown up car fuse could be the culprit that has stopped the windshield wipers from working. Check the fuse assembly under the dashboard of the car. Replacing a blown fuse might fix the problem of windshield wipers not working.

    Windshield Wiper Sprayers Not Working - Things to Check

    Sometimes the windshield wiper sprayer stops working which can be very annoying. The washer mechanism is a self cleaning mechanism for the windshield. Here are some of the things that you need to check in case it is not working.

    Check Windshield Washer Motor
    The windshield washer mechanism might have been impaired due to the malfunctioning of the wiper washer motor. Check if its working and get it replaced if it is beyond repair.

    Check Windshield Washer Fluid Level
    Sometimes the washer doesn't work because the washer fluid levels are not filled to requisite levels. Filling in fluid might restore normal functioning.

    Check For Broken Washer Hose
    The connecting washer hose that connects the reservoir to the nozzle, might be broken or worn out stalling the overall operation. Check the hose for leaks and get it replaced.

    Check Washer Nozzle For Clogging
    Last thing to check is the nozzle of the washer for clogging. An obstruction in the washer nozzle might be the reason for windshield wiper sprayers not working. Using a pin, clean the clogged nozzle. This might restore the sprayer to the normal working condition.

    Jun 07, 2010 | 1998 Saturn SL

    1 Answer

    Need to get a programmer dont know where its at


    • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
    • Damaged turn signal and windshield wiper switch .
    • Damaged windshield wiper motor .
    • Damaged windshield wiper control module.
    7fd52e7.gif
    efd7dbe.gif
    Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
    Windshield Wiper System The windshield wiper system consists of :
    • Windshield wiper motor (17508) (F-type).
    • Washer system.
    • Windshield wiper control module.
    • Turn signal and windshield wiper switch (13K359).
    The windshield wiper control module is:
    • Located at the instrument panel fuse panel.
    The windshield wiper motor is:
    • Attached to the cowl top extension (021A36) .
    • Connected to windshield wiper mounting arm and pivot shaft (17566) .
    The turn signal and windshield wiper switch features a:
    • Rotary wiper switch.
    • Push type washer actuator.
    OFF/Low/High Speed
    • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
    • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
    • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
    • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
    • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
    • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
    • When the park switch contacts open, the windshield wiper motor stops in the park position.
    Interval
    When the turn signal and windshield wiper switch is in the interval position:
    • The wipers make single wipes separated by pauses.
    • The rotary switch is on the end of turn signal and windshield wiper switch .
    • The length of the pause can be set from approximately 1 to 17 seconds.
    • Length of pause decreases as the rotary switch is rotated away from off.
    • Length of pause increases as the rotary switch is rotated toward off.
    While in the interval wiper mode:
    • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

    May 27, 2009 | 1994 Ford Mustang

    Not finding what you are looking for?
    1998 Jaguar XK8 Logo

    Related Topics:

    179 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jaguar Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Raygin
    Raygin

    Level 2 Expert

    322 Answers

    yadayada
    yadayada

    Level 3 Expert

    61168 Answers

    Are you a Jaguar Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...