Question about 1985 Chevrolet Corvette

1 Answer

I need a wiring harness for the transmission overdrive of a 1985 corvette

Posted by on

  • JEDLIPS May 11, 2010

    If you find a spare ,please bell me

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 226 Answers

I have them for auto and manual

I cant get my file upload to work

Ill need your email to send them to you if you want them.

Posted on Mar 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 f 150 transmission overdrive fuse


The problem is that either the wiring harness going to the overdrive control motor has chafed and is shorting out, or the overdrive control motor is bad. Check out the wiring harness VERY carefully, if it's OK replace the control motor.

Apr 16, 2014 | 2003 Ford F-150

1 Answer

My 97 sierra c1500 has no overdrive. Every other gear works fine and it runs fine it just wont go into overdrive. When you step on it, it will still speed up but the rpm`s ride higher and higher and i


You should check error codes (DTCs) with a code reader to see if that will shed light on the problem. Overdrive is controlled by a solenoid in the transmission which locks the torque converter. Sounds like the control wire to the solenoid has become disconnected or cut, or the solenoid has failed. I would get the wiring diagram from either Alldatadiy.com or a service manual and trace it back from the transmission to determine if wiring is the problem.

Jan 17, 2018 | Cars & Trucks

1 Answer

I have a 1985 Corvette. The battery was dead and I had the charger on it. I went to start the car with the charger on it. There is a wire that runs off the positive side of the battery and into the harness...


The fuseable link that is on it should protect the vehicles electrical at three places one for ignition switch a second for starter control and third for charging control ,The one on the positve is for the charging system

May 08, 2011 | 1985 Chevrolet Corvette

1 Answer

98 chev corvette auto transmission will not shift into 3rd gear or overdrive


I would start by checking the fluid level in your transmission. If it is fine, then it's possible one of the solenoids in the transmission is going bad. Is the check engine light on? Goodluck

Mar 27, 2011 | 1998 Chevrolet Corvette

1 Answer

1994 CHEVY CORVETTE, PULLED A DI DISTRIBITOR OUT PUT BACK NOW WILL NOT FIRE.


hooked up the harness, right? Is the rotor back in? the only other thing is it is not lined up properly, and you will have to get the engine to #1 compression at TDC and pull the distributor, line the rotor up to #1 wire on the cap.

Mar 23, 2011 | 1985 Chevrolet Corvette

1 Answer

Will a LT 1 engine from a 1994 z 28 camera install in a 1992 corvette with same engine and the same transmission without changing the electronic brain or the wiring harness


even though the LT 1 from the Z28 camaro and the corvette are similiar that is where it ends. Each car is programed differently, From the fuel pump to the o2 cencers. Alot of the wire connections will not match up if you do not change the wire harnesses. The computer might get fried if you try to "short cut" this project. Granted "some" parts are interchangable. Use caution when trying to interchange engines and transmissions. Aftermarket parts are avaible to make the swap easier. But its better to have a pro. do the swap and keeping it emissions legal.

Nov 16, 2010 | 1992 Chevrolet Corvette

2 Answers

Overdrive doesnt want to work while its engaged


SOUND LIKE CLUTCH IS WORN SLIPPING CAUSING NO OVERDRIVE.

Jun 08, 2010 | 1985 Chevrolet Corvette

1 Answer

1985 corvette doesn't have drive or overdrive


Sounds as if you need a new clutch plate. Try starting in a higher gear and if you have excessive slippage, that's what it is.

Jul 05, 2009 | 1985 Chevrolet Corvette

3 Answers

Need to remove ECM out of my 1985 Corvette


well your in luck i just removed mine today lol. there are 5 1/4 inch screws on the bottom side of the dash on the passenger side of the car remove them pull the plastic cover down and disconnect the light mounted on the piecce you just removed next make sure your battery is disconnected cause it may fry it if power is connected. Next you will need a 10mm look straight up you will see the box it is aluminum with 2 wire harness attached. There is a metal clip holding it attached pull it back and un hook the harness then it will slide right out.

Dec 01, 2008 | 1985 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...