Question about 2000 Plymouth Breeze

1 Answer

Car bogs while running and stalls

Rpm and speedometer gages shut down when engine light comes on. had it hooked up and got hits on crank shaft sensor and distributor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

So what was the fault codes on the OBD 2 scan retrieval??start with that!!

Posted on Dec 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While driving engine just shuts off then it will not crank for a few minutes then it will start and run fine it acts like key was shut off and it dont crank at all.09 gmc sierra 4.8


I didn't see year--make--model listed?
How long since a tune-up?
Are there any applicable trouble codes?
With intermittent issues, you have to test when problem is ongoing. I realize testing can be a problem when sitting along side the road, somewhere, but, do what you can.
After it stalls, if it cranks good but won't start, have a helper crank it while you check for spark at the spark plugs, gasoline engine. If spark everywhere, use a gage and check proper fuel pressure and fuel injector pulse. Make sure battery has a full charge and battery connections all good.
If you lose rpm signal, the vehicle will die. If you lose that signal, it will probably effect more than one component, that's why you need to check for more than one issue. The rpm signal comes from crank sensor. Don't replace anything unless your testing points in that direction.

Apr 18, 2016 | Cars & Trucks

1 Answer

F250 diesel 2001 running then engine stalls after 30 minutes


Ford had a problem with the cam shaft sensor located on passenger side of engine on crank shaft thois will cause the engine to shut down.

Apr 20, 2014 | 2001 Ford F250 Super Duty Super Cab

1 Answer

2002 jeep Cherokee 2.5crd engine cuts after removing foot from accelerator pedal . no warning lights come on. let the vehicle stand for 10 minutes then it starts up again. can it be injectors or ignition...


check all fuses.
cuts out hot or cold engine.????????
if it wont start and car gets 60k tuneup (?)
then connect scan tool and crank for 5 seconds.
see if you get scan DTC errors , cranking (release key) see em?
stalls are caused by over 50 reasons. guessing is impossible or very expensive.
enter: Diagnosis,
you take measurements, and find the failure path then work that path like bird dog.
2.5L 4cyl engine. I just sold min last week. with 5sp M/T
cuts out, does that mean the engine stalls?
we need to know what it really does.
1: stalls (engine rpm drops to 0 RPM)
2: engine rpm drops to 300rpm and shakes.
3: power loss from engine?
4: only stalls at stop signs...?
5: bogs all them time, same as #3
6: engine misfires (shake)
7: bogs only on throttle TIP-IN then recovers.
8: bogs only on hills.

i wait.
when dead, is spark lost?

Aug 21, 2013 | Jeep Liberty Cars & Trucks

1 Answer

2002 grand am ecotec Rpm bounce 400-900 when engine is cold


Try and clean the throttle body. Carbon will gum up on the blade and the vaccume passages, which will cause a surge and stall.

Oct 28, 2009 | 2002 Pontiac Grand Am

1 Answer

Crank shaft sesor/cam sensor problem?


If you had a fault with the crank sencer your car would not start.Sounds like the air flow meter is giving you the problems.

May 28, 2009 | 2005 Dodge Neon

1 Answer

Check engine light is on


remove positive battery for five minutes to re set the computre hook it back it should go out

Jan 05, 2009 | Hyundai Motor 2004 Sonata

1 Answer

Check engine light comes on & engine bogs down


you need to have it scanned for codes

Nov 10, 2008 | 1995 Toyota 4Runner

3 Answers

2000 jeep cherokee starts then stalls in approx 3 sec 4.0 has new crank sensor


I am going to assume that it will not run even if you push on the accelerator pedal?
Can you install or attach an old timing light to the spark plug wires, turn it one and try to start it. The light should flash with the engine running, but if it shuts off at time of engine die, and the engine is still spinning, you are losing spark, My suggestion is the cranks shaft sensor on bell housing.
Second, install a pressure gage on the test port on the fuel rail and watch it as you start the engine, fuel pressure should not drop as the engine dies, if it does, the pump is not working correctly. There are two modes of power to that pump, one to start and timed, for only a few seconds to prime the system, and one to run continuously. Find the wires going to the pump at the tank. Connect test light to those wires and watch what happens during crank and at stall, You should not have the pump shut off and the engine dies.
If you have spark, and fuel pump working, when did you last change the filter,,but I put that LAST.
It has to be one or the other of these.
Good Luck

Aug 04, 2008 | 2000 Jeep Cherokee

Not finding what you are looking for?
2000 Plymouth Breeze Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...