Question about 2006 Suzuki Forenza

1 Answer

Ignition lock frozen

My steering wheel is froze in the locked position i can insert and remove the key car is auto in park i have tried too wiggle the wheel sharply back and forth while turning the key i havent had any luck i most likely will have the car towed unless someone can help me repair this myself thanks everyone

Posted by on

  • Anonymous Jan 16, 2009

    my key won't turn in the ignition and I think it's because it's frozen. I don't know what to do about it. I'm going call an auto part store and see if they can give me any ideas.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Can you move the shifter ?? Try foot on brake too!!could be a bad key ! Or maybe shifter jammed or your switch for your key ?? Try holding the stering wheel too the left hard and try turning the key !!!

Posted on Jan 16, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: key gets stuck in ignition

My daughter drives a Suzuki, my solution to her is: while the gear shift lever is in park, lightly put pressure on the gear shift lever, through the park position and while pressing the gear shift towards park light rock left to right while trying to remove the key.

The interlock between the transmission and the ignition switch needs to be adjusted/ repaired or replaced.

Posted on Oct 16, 2008

  • 5 Answers

SOURCE: ignition key / lock steering

Try spraying WD 40 into the ignition as possible. Let sit a second.. Then try working the key. It should come out. Then work the key in and out and turn on and off; a few minutes. This is to loosen the ignition up. I had the same problem, once with my car key. The key came right out.

Posted on Mar 25, 2009

  • 265 Answers

SOURCE: Suzuki Sidekick Won't lock in Park

Jiggle the steering wheel - make sure brake is depressed.

Posted on Feb 06, 2010

  • 102 Answers

SOURCE: When I put the key into the ignition and try to

Firmly grab the steering wheel ,left hand on the 2,o'clock position,and with your right,at the 8,o'clock position and turn it until you feel the wheel move ,let go of the 8 ,oclockand try the key ,,,,,this may take a couple of try's.
Good luck

Posted on Mar 08, 2010

  • 1403 Answers

SOURCE: the key has broken in

on the left side of barrel, look for a dowel, there should be a vary small opening that you can take something as small as a pinhead and push the dowel in ,while pushing in on dowel pull the barrel out.the key may need to also be in on position for removal. try that and see if it works. if not please repost your question. thank you for choosing fixya.com

Posted on Dec 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Aerostar Steering Wheel Lock


quite often we have to wiggle wheel some to get them unlocked even in newer cars .

Dec 14, 2017 | Cars & Trucks

2 Answers

I have a 2009 Kia Rio. When i put the key into the ignition it will not turn therefore the car will not start.


wiggle steering wheel up and down sometimes the steering lock tab jams and wont permit key to turn ====if key worn down will not let ignition cylinder turn other is bad ignition cylinder

Jul 30, 2016 | 2009 Kia Rio 1.6

2 Answers

Key ignition wont turn


APPLY BRAKE AND MAKE SURE STEERING WHEEL IS CENTERED. IF IT IS PARKED SO THERE IS PRESSURE ON THE FRONT WHEELS AND HOLDING THE STEERING WHEEL HARD RIGHT OR LEFT IT WILL MAKE THE KEY VERY HARD TO TURN.

Mar 03, 2015 | 2009 Kia Optima LX

2 Answers

I have a 95 camaro, I put the key in ignition and it will not turn the ignition. It's like it's stuck. Replaced the ignition module and still cannot turn ignition. Help!


the ignition module (ignition switch on top of the steering column) normally doesn't get stuck.

things you can try:
steering wheel lock: (the pin gets a "burr" on it and locks everything up) wiggle steering wheel back and forth while trying to turn key.

transmission lock (parking on an incline will jam up the interlock)
push the shifter farther into park while trying to turn the key, or wiggle shifter

Sep 19, 2014 | 1995 Chevrolet Camaro

1 Answer

Bmw e60 523i 2005 is not turning the key to on the car


is the steering locked if it is you need to rotate the steering wheel back and forth while turning the key to release the lock, if the steering is turned all the way then try turning the steering wheel right while wiggling the key in the ignition to release the lock, if the steering wheel is free then get some graphite from an auto parts store and put it on the key and insert it into the ignition to get it lubricated

Nov 11, 2013 | Cars & Trucks

1 Answer

1996 Ford Taurus. After parking car and returning, the ignition key will not turn, the steering wheel is locked in place and Parking gear is frozen. What to do.


try to turn the wheel so that the steering wheel dose not have a load on it while truning the key also you may want to try and "wiggle" the shifter if it is located on the colum.

Apr 29, 2011 | Ford Taurus Cars & Trucks

1 Answer

I have a 1998 Ford Contour. When I insert the key it will not turn. I have tried the standard stuff like wiggle the steering wheel, push in the brake and try to move the car from park, nothing! If I use...


You will most likely need to replace the ignition lock cylinder.

Functional Lock Cylinder
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column covers.
  3. Turn the ignition lock to the accessory position.
  4. Insert a 0.125 (3.17mm) wire pin or small drift punch in the hole at the top of the cylinder housing and depress the retaining pin while pulling out the lock cylinder To Install:
  5. Turn the new lock cylinder to accessory position and while pressing the retaining pin in, insert the lock cylinder into the housing.
  6. Turn the key to the OFF position the release the retaining pin.
  7. Try the lock cylinder operation in all positions.
  8. Reinstall the steering column covers.
  9. Reconnect the negative battery cable.
Non-Functional Lock Cylinder
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column covers.
  3. Insert a 0.125 (3.17mm) drill bit in the hole at the top of the cylinder housing and drill out the retaining pin. NOTE: Be careful not to drill into the lock cylinder housing.
  4. Pull out the lock cylinder.
  5. Clean out all the metal shavings and check the tube for damage. If damaged, the housing must be replaced. To Install:
  6. Turn the new lock cylinder to accessory position and while pressing the retaining pin in, insert the lock cylinder into the housing.
  7. Turn the key to the OFF position the release the retaining pin.
  8. Try the lock cylinder operation in all positions.
  9. Reinstall the steering column covers.
  10. Reconnect the negative battery cable.

Remove the three screws and remove the lower column cover


tecnovative_168.gif


Releasing the lock cylinder retaining pin



tecnovative_169.gif

Mar 21, 2011 | 1998 Ford Contour

1 Answer

What is the procedure to changing an keyed ignition lock?


Hi there,

Removal

Disconnect the negative battery cable with the proper size wrench and place away from the battery.
Insert the key into the ignition lock cylinder and turn the key to the run position.
Remove the steering column cover on a tilt steering wheel model by pressing the upper and lower section of the cover together and pulling free from the mounting plate. Remove the steering column covers on a non tilt steering wheel model by using a Philips screwdriver and unscrewing the mounting screws.
Disconnect the electrical connector from the ignition switch by lifting up on the release tab and pulling.
Press the ignition switch actuator pin by pushing a small screw driver into the key lock cylinder, while doing this pull the ignition switch out of the ignition switch housing.

Installation

Insert the new key into the new ignition switch and turn the key to the run position. Insert the new ignition switch into the ignition switch housing. Wiggle the switch back and forth until the actuator pin mounting hole is aligned and falls into place.
Install the electrical connector back into the connector housing by pressing it in with your hands.
Place the steering column covers back onto the non tilt steering wheel and insert mounting screws. Tighten screws using a Philips screwdriver. Place the steering column covers over the tilt steering wheel and press the upper and lower portion together to snap covers back into the mounting plate.
Pull on the ignition key to ensure switch is locked into place. Turn key to the "off" position and remove the key. Insert the key and start the vehicle.

Hope these help.

Jan 28, 2011 | 1992 Ford Crown Victoria

1 Answer

I can't get the rod that connects the key lock and door latch in the right position to work correctly.


  • Disconnect the negative battery cable with the proper size wrench and place away from the battery.

    Insert the key into the ignition lock cylinder and turn the key to the run position.
  • 2 Remove the steering column cover on a tilt steering wheel model by pressing the upper and lower section of the cover together and pulling free from the mounting plate. Remove the steering column covers on a non tilt steering wheel model by using a Philips screwdriver and unscrewing the mounting screws.
  • 3 Disconnect the electrical connector from the ignition switch by lifting up on the release tab and pulling.

    Press the ignition switch actuator pin by pushing a small screw driver into the key lock cylinder, while doing this pull the ignition switch out of the ignition switch housing.
  • Installation
  • 1 Insert the new key into the new ignition switch and turn the key to the run position. Insert the new ignition switch into the ignition switch housing. Wiggle the switch back and forth until the actuator pin mounting hole is aligned and falls into place.
  • 2 Install the electrical connector back into the connector housing by pressing it in with your hands.
  • 3 Place the steering column covers back onto the non tilt steering wheel and insert mounting screws. Tighten screws using a Philips screwdriver. Place the steering column covers over the tilt steering wheel and press the upper and lower portion together to snap covers back into the mounting plate.
  • 4 Pull on the ignition key to ensure switch is locked into place. Turn key to the "off" position and remove the key. Insert the key and start the vehicle.


  • hope this helps you

    Dec 21, 2010 | Ford F-350 Cars & Trucks

    Not finding what you are looking for?
    2006 Suzuki Forenza Logo

    Related Topics:

    109 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Suzuki Experts

    Marvin
    Marvin

    Level 3 Expert

    81294 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8841 Answers

    Are you a Suzuki Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...