Question about 2003 Lincoln Town Car

2 Answers

I need to replace my pwr seat switch in my 2003 lincoln town car. I got a door panel tool but the door panel is not coming off. I also found a torx bolt behind the door handle but can not find anymore bolts to remove. I do not want to ruin my door. does someone know how to get in there.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 126 Answers

There is two screws in pull handel there is two screw at bottom of door panel in the carpet the rest are plastic clips .

Posted on Apr 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Lincoln town car power seat


boot wont unlock pergut 307

Nov 10, 2013 | 2003 Lincoln Town Car

1 Answer

1996 LINCOLN TOWN CAR NO POWER AT FUEL PUMP


if u a fuel cut off switch. check to see if u have fire at switch. pwr from fufuel pump comes from the fuel cut off switch. check your owners manuel for location

Jan 22, 2013 | 1993 Lincoln Town Car

1 Answer

How do i remove the power window switches from the doors? what special tools should i use?


From 2003 Town Car Workshop Manual / SECTION 501-05: Interior Trim and Ornamentation

REMOVAL AND INSTALLATION
Procedure revision date: 01/28/2002

NOTE: LH side shown, RH side similar.

  • Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  • Remove the window switch plate.
  • Disconnect the electrical connectors.
  • CAUTION: Use care not to damage the trim panel covers. Open the screw covers.
  • Remove the screws and the assist handle.
  • Remove screws and the front door trim.
  • Disconnect the electrical connectors.
  • To install, reverse the removal procedure.

Hope helps.

Jun 10, 2010 | 2003 Lincoln Town Car

1 Answer

How to remove front dopr panel on 1995 Lincoln Town Car


Front Door Panel - Town Car - Removal
CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

Snap out two door pull strap retaining screw covers. Remove screws.

Remove two screws on front and rear side of front door trim panel.
The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

Disconnect driver seat regulator control processor switch (driver door only) if equipped.
Twist out interior lamp wire assembly and remove the front door trim panel.
Installation

Ensure plastic watershield is secured to door panel.
Position front door trim panel to door. Connect interior lamp wiring.
Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
Align door lock side to its mating slide on the sheet metal (front doors only).
Snap in front door trim panel. Ensure all retainers fit properly.
Install two retaining screws on front and rear side of front door trim panel .
Install two retaining screws and pull strap covers.

Good luck Remember rated this).

May 31, 2010 | Lincoln Town Car Cars & Trucks

1 Answer

2003 Lincoln Town Car - Power window switch removal/installation


SECTION 501-05: Interior Trim and Ornamentation 2003 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/28/2002 Front Door Trim Panel adobe.gif Printable View (206 KB) Removal and Installation
NOTE: LH side shown, RH side similar.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Remove the window switch plate.
    a0045307.gif
  1. Disconnect the electrical connectors.
    a0044981.gif
  1. ani_caut.gif CAUTION: Use care not to damage the trim panel covers.
    Open the screw covers.
    a0045817.gif
  1. Remove the screws and the assist handle.
    a0045818.gif
  1. Remove screws and the front door trim.
    a0045819.gif
  1. Disconnect the electrical connectors.
    a0045834.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n306887&c35=wsm%2cfront%20door%20trim%20panel%2cs3g%2c501-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=modem&hp=n&[aqe]

Apr 02, 2010 | 2003 Lincoln Town Car

2 Answers

Where is the door module located on a 2003


Remove the driver door panel. You will have to remove the two screws that hold the door closing strap and the one screw behing the interior driver door handle. Gently pull the door panel off by first lifting the panel over the manual lock/ unlock nipple/ shaft. The module is located at the top right corner of the driver door.

Mar 12, 2010 | 2004 Lincoln Town Car

3 Answers

How do you change the door hinge pin? On 1997 lincoln town car?


Well cracklin joe half the hinge us welded to the door..Duh!

Jan 08, 2010 | 1997 Lincoln Town Car

1 Answer

I'm trying to get the drivers door trim off my 89 town car to replace the power seat switch. I have all the fasteners loose and the door panel comes off a little. It seems to be stuck on a linkage that...


You will have to pull the little chrome knob off the manual door lock slide, and then push the wire linkage back until it unsnaps from the plastic slide on the backside of the door panel.

Oct 23, 2009 | 1989 Lincoln Town Car

3 Answers

Lincoln Town Car 1999 driver side window switch


The plastic piece around the switches comes off and the entire cartridge comes out. It just snaps into the armrest. My 98 continental having similar issues. All other switches work, drivers window just quit. Tried a new cartridge did not fix problem.....still working on it.

Apr 06, 2009 | 2000 Lincoln Town Car

1 Answer

95 lincoln town car power driver seat goes forward, but not back?


on our 93 lincoln town car it was the switch that was not working we had to remove the control panel for the seat switch on the driver door and replaced it with one from a salvage yard.

Mar 11, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
2003 Lincoln Town Car Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...