Question about 1999 Mercury Cougar

1 Answer

Need to replace driverside cv joint

I got it all apart just cant pry the joint out

Posted by on

  • trill1119 Dec 19, 2008

    I tried that and it wont budge I guess ill just give it more umf

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

Use a crowbar or something that fits in there & pop it ot from trany side..

Posted on Dec 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to pull gearbox out but cant figer out how cvs come out


IF YOU CANT TAKE A PRY BAR AND PRY THE INNER CV JOINT.CHECK CV JOINT YOU PROBABLY HAS 3 BOLTS HOLDING DRIVE AXLE IN PLACE.

Jun 12, 2011 | 1992 Nissan Sentra 4 Door

1 Answer

Tring to remove cv joint on 2001 intrepid but transaxel shaft seems stuck to cv joint cant dislodge.....does it have a lock or something.......whats the best way to remove


use a large pry bar pry the inner tripod cv joint out of the transaxle differential gears.you have a retaining circlip that holds transaxle in place in the transaxle.besure to replace circlip and o ring seal on the transaxle stub shaft.torque strut assembly to steering knuckle attaching bolts.install the nuts to the attaching bolts and while holding bolt heads torque to 125 ft lbs and torque axle hub nut 125 ft lbs

May 18, 2011 | 2001 Dodge Intrepid

1 Answer

How to change driverside c-v joint chevy venture


You don't change the cv joint. You purchase a half shaft left or right side and you replace the whole axle shaft they are around $150.00. Take off the tire, remove axle shaft nut, remove spindle from lower ball joint and pull the axle out of spindle then you take a large pry bar and carfully pop the axle shaft out of the transmission. Very easy job only takes about 1 hour to for complete job.

Feb 23, 2011 | 2002 Chevrolet Venture Passanger

1 Answer

How to change a Cv joint on a 1997 Pontiac Grandam


While the car is still on the ground remove the half shaft nut then jack the car up and support it with jack stands and remove the tire. after you get the tire off you may have to remove the break caliper and the rotor, if you have to do this now. Remove the lower ball joint nut and break apart the ball joint with a large pry bar by prying down on the lower a frame. grab the steering knuckle with both hands and pull until the half shaft is free from the bearing hub assembly. then grab the half shaft and give it a good tug to remove it from the trans axle, you may have to pry it out with a small pry bar wedged between the inner cv joint and the trans axle. at this point I would replace the entire half shaft it is cheaper and a lot easier than replacing the cv joint. installation is reversed but be careful of the splines when installing the half shaft back into the trans axle and the bearing hub. Good luck.

Nov 02, 2010 | 1997 Pontiac Grand Am

1 Answer

How do I remove the driver-side inner axle shaft


its retaind with a roll type snap ring. you need to POP it out. being carful not to damage it seal, pry with a good jolt between the trans and cv cup, or take a pry bar or pipe and jab at it like your stabbing it lol. dont use a hammer or go crazy but it takes a good wallop to release. then slide it out, to install, trun till it drops in and POP it in by hand with the slop in the cv joints.good luck!

Sep 04, 2009 | 1994 Mazda Protege

1 Answer

How to replace a cv joint on a 2005 toyota corolla, i cant get the cv joint back part off the transmittion. driver side cv joint broke and rear part is stuck to transmittion..


There are two types of cv joints used. One type bolts on the other you have to pop out. Do this by prying it out with a big screwdriver. A c-clip hods it in and it will pop out for you. When reinstalling be sure it seats back in.

Jul 26, 2009 | Toyota Corolla Cars & Trucks

1 Answer

Inner cv joint disassembly


If you are changing the CV joint with shaft, after getting the outer end of the shaft out of the hub, Take a small pry-bar and pry the shaft out of the tranny.

Mar 14, 2009 | 1997 Chevrolet Cavalier

1 Answer

1992 voyager driver side cv joint


with a pry bar or pry between the trany and cv or put the pry bar on the cv and hit it with hammerits just a little c clip holding it good luck pierre

Jan 24, 2009 | 1992 Plymouth Voyager

Not finding what you are looking for?
1999 Mercury Cougar Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...