Question about 1995 Chrysler Concorde

1 Answer

Hey, i have a 95 concorde and i can't get my hood to open. the little thing to open the hood broke and a mechanic loosened the plastic top so i could pull the little metal wire to open the hood, i keep pulling it, but it doesnt seem to loosen the "lock" and i can't get the hood open to re-charge my battery. what else could i do?

Posted by on

  • timmybenner Dec 19, 2008

    worked perfect thanks.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 6,674 Answers

Try pushing down on hood as you pull the wire.

Posted on Dec 19, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a BMW 328i 1997 and I broke the hood latch to open the hood. How do I open the hood or fix it with little work?


Can yu reach the lock mechanism at front of hood w a long screwdriver. pry back where cable for release is attached for first latch. then as you would normally for safety latch.

May 15, 2017 | BMW Cars & Trucks

1 Answer

Thermostat replacement


on the 95 Concorde 3.3 the thermostat is right in front of you when you open the hood it has what looks like a grease nipple on it and it has the big hose that comes from the rad make sure you put a new gasket on with a small amount of sealant and the thermostat go`s in the right way .

May 12, 2012 | 1995 Chrysler Concorde

1 Answer

My hood latch on my 95 f-150 pickup truck is not working


If you can get it up. lube the catch mechanism, above and below. Lube the hood hinges at the rear of hood, work it up and down a few times before you try closing.
I hope you haven't bent anything at the rear hinge points, or the front catch?

Jun 20, 2017 | 1995 Ford Explorer

2 Answers

Broken hood latch 2001 chrysler concorde


you can use needle nose pliers pull the hood release cable on inside car where cable broke from handle.needle nose pliers will help you enough to pull cable to open hood so you can replace fix hood release handle and cable.

Sep 27, 2011 | 2001 Chrysler Concorde

1 Answer

Where is the alternator on a 2003 chrysler concord and how do you change it what tools do i need


FIRST TURN OFF RADIO THEN DISCONNECT NEGATIVE BATTERY CABLE.IF YOU HAVE 2.7L ENGINE YOU HAVE TO REMOVE LOWER PLASTIC SPLASH SHIELD, REMOVE TRANSMISSION COOLER AND POSITION IT ASIDE.LOWER RADIATOR CROSSMEMBER SUPPORT, LOOSEN DONT REMOVE,ADJUSTING T BOLT AND THE PIVOT BOLT LOOSEN BELT ADJUSTING BOLT, REMOVE DRIVE. REMOVE ALTERNATOR FIELD CIRCUIT PLUG. REMOVE ALTERNATOR BATTERY PLUS TERMINAL NUT AND WIRE REMOVE.PIVOT BOLT SPACER CAREFUL DONT DROP LOSE SPACER. THEN REMOVE ALTERNATOR. YOU NEED BELT TENSION GAUGE TORQUE ADJUSTING T BOLT UNTIL TENSION GAUGE READS 120 LBS USED BELT NEW BELT 180 - 200 LBS. YOU NEED ALL BASIC MECHANIC TOOL SET WITH METRIC SOCKETS METRIC OPEN BOX END WRENCHES.SIZE WRENCH RANGE 5MM UP TO 19MM NEED ADJUSTABLE PLIERS NEED SCREW DRIVERS LIKE FLAT HEAD AND PHILLIPS. YOU NEED TORQUE WRENCH. FOR THE PIVOT BOLT NEED TORQUE TO 40 FT LBS. THE 8MM MOUNTING BOLT TO 30 FT LBS. 10MM BOLT TO 40 FT LBS.

Sep 08, 2011 | 2000 Chrysler Concorde

1 Answer

How do u get the hood to open on a 99 vw passat if the pully is broke off


Under the car:
You will be able to open the hood if you pull off your splash guard and use a long long flat head screwdriver or something like that. You'll see the hood latch in front of the radiator with the cable attached to it at the top near the hood, put it on the drivers side edge of the bottom of the latch and pry to the passenger side, the lever moves from the drivers side to the passengers side, the cable basically pulls the top of it to achieve this. so your doing the same thing on the bottom with the screwdriver.


tdisline_492.jpg


Release the latch from underneath by the lever that you have to pry towards the passenger side. Then open the hood, and replace the safety release mechanism broken part.

May 01, 2011 | 1999 Volkswagen Passat

1 Answer

The hood latch on my 95 VW Jetta is broke. I


well if the cable snapped you will need to try to get the front grill to pop out with out breaking it and look up and in to get to the little latch for the hood release.

Sep 11, 2009 | 1995 Volkswagen Jetta

1 Answer

190d hood can`t open!


Look at the little opening just to the left and down a little from the Mercedes emblem on the grille.  There used to be a latch there.  If the latch is missing, you can run a wire through the opening and attach to the hood release mechanism so that you can pull it to open the hood (that is of course after you pull the hood release which is located under the dash on driver side left.

Mar 28, 2009 | 1990 Mercedes-Benz 190

Not finding what you are looking for?
1995 Chrysler Concorde Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

82188 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...