Question about Hyundai Motor 2003 Elantra

1 Answer

2003 elantra alternator problems

The bolt that holds the top part of the alernator keeps loosening. i had to replace it after it feel out and destroyed one of the belts. two weeks later its really loose again. i dont know whats wrong with it and how to fix it. help!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Hyundai Master
  • 1,121 Answers

This case needs an expert to check whether the threads where the bolt goes in are good or are worn.If worn has to remake new threads and renew bolt.

Posted on Aug 16, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: trying to replace alternator on

just remove fan it will slide out the front

Posted on Jan 07, 2010

  • 76 Answers

SOURCE: Elantra Steering Wheel Noise

Check and make sure that your power steering fluid is topped off. Could possibly problems with your power steering pump. Mine does the same and the fluid is full. I just keep an eye/ear on it. If it continues to get worse than it could be the pump going out. If the fluid is allowed to get too low, it could possibly get air in it affecting both the "feel" of the steering and making a noise.

Posted on Sep 28, 2008

  • 1 Answer

SOURCE: alternator removal on 2001 Hyundai Elantra

All I did was wiggle the bolt out . You have to loosen the power steering pulley and bracket and remove the fan shroud on the left side.

Posted on Jun 18, 2009

  • 38 Answers

SOURCE: How to replace serpentine belts 99' Hyundai Elantra.

you might need to get a prybar or something such long, and try to pry it off the belt, it should go easy right away. It is a spring-inside assembly, and won't brake. There also could be a 3/4 hole in it, look from a side. It's for middle size ratched, it can be used to loosen the tensioner from serp. belt.

Posted on Jul 08, 2009

edwardjwoods
  • 372 Answers

SOURCE: TCS ABS lights on & alternator not fully charging

Alt shoud be putting out 14 to 15.2 volts.

Posted on Jul 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust the tension on the alternator belt for my 2003 Hyundai Tiburon?


Adjusting alternator belt tension - bolt & pivot bracket design ...

? 13:06
https://www.youtube.com/watch?v=8JN0RtZk_2Y
Nov 26, 2012 - Uploaded by backyardmech
Releasing tension on the alternator belt to remove the alternator- 4 cylinder Honda in this video. ... How to ...

How To Install replace Alternator Belt 1999-06 Hyundai ...

? 4:51
https://www.youtube.com/watch?v=6IWgXTijclo
May 15, 2013 - Uploaded by 1A Auto Parts
How To Install replace Alternator Belt 1999-06 Hyundai Elantra 2.0L .... Adjusting alternator belt tension ...

Dec 21, 2015 | 2003 Hyundai Tiburon

1 Answer

How do I install the alternator on a 2003 KIA Spectra?


I just replaced the alternator on my 2003 Kia Spectra, not an easy job. It has to be removed from under the vehicle. First, after disconnecting the battery, remove the "locking" bolt on the topside of the alternator, along with the adjusting bolt (both metric 12mm). This is done from the topside, (rear, right side of the engine compartment). From under the vehicle, loosen the bolt that holds the alternator. At this point you have to decide whether to loosen the exhaust manifold or motor mount. I choose the motor mount. I loosened the mount and used a floor jack to raise the engine, only needed about an inch. Good luck.

Oct 10, 2014 | 2003 Kia Spectra

1 Answer

How do you change the alternator and replace it with new alternator, for a 2003 Nissan Altima, with a 2.5 L engine ?


The alternator is right on top of the 2.5L motor and held on by 2 14mm bolts. To remove the lower bolt (hard to reach), you must remove the coolant bottle and the IPDM fuse board and its metal box/bracket. A breaker bar really helped give enough torque to loosen the 2 bolts. Approach the drive belt from under the front passenger tire. There is a tension adjuster (hard to reach) bolt that loosens the belt and allows you to remove it from the alternator. If the belt is still good, (don't remove entirely) save time and try to keep the belt in a similar position. I am not an experienced mechanic and job took me about 3 hours & $200 for the alternator.

Apr 16, 2010 | 2003 Nissan Altima

1 Answer

How to change altenator belt


loosen the bolts on the alternator. One is a pivot point the other slides along the mounting bracket to vary the tension on the belt.

Swing the alternator inward to loosen.
Remove the belt.
Install the new one.
Pull the alternator out to tighten the belt.
Hold in place and tighten the tension bolt.
Tighten the pivot bolt.

Correct belt tension: at the mid point on the belt along the longest run press down. It should move about a quarter of an inch of so.




Mar 07, 2010 | 2000 Hyundai Elantra

1 Answer

How do I replace an alternator on a 2000 VW Passat 1.8T. How hard is it to replace?


it isnt that hard actually

disconect positive battery terminal. and feel the tension on the laternator belt. you will need to bring it back to this tension.

1.) loosen bolts holding alternator in place (LOOK AT THE BELT TO REMEMBER HOW IT GOES, BEST NOT REMOVE THE BELT.)

2.) loosen bolts holding wires to alternator and connect wires to new alternator

3.) Place alternator in engine, replace bolts but dont tighten

4.) put belt in place, it will be slack, use your tire iron or a piece of pipe or wood to pry the alternator back, to bring tension on the belt. You pry the alternator to pull the belt as TIGHT AS POSSIBLE. while holding strain, on it, tighten the bolts.

Feb 27, 2010 | 2000 Volkswagen Passat 4Motion

1 Answer

How to replace a thermostat on a 2003 chevy trailblazer with a 4.2 engine. One source says it is off the top radiator hose, and another says it comes from the bottom hose right behind the alternator. If it...


The thermostat is under the alternator.

If you have a memory saver to keep radio & PCM settings, install it now.

Remove negative battery cable from battery. Remove positive cable from alternator and disconnect harness plug from alternator.

Remove accessory belt noting how it is installed for later reinstallation.

Remove engine lifting hook in front of alternator.

Remove (3) bolts holding alternator on.

Drain coolant from radiator (may want to start this as first step as it takes a while). Loosen pressure cap to aid in system draindown.

Remove radiator hose from thermostat housing.

Remove two bolts from housing and remove from engine.

Reinstall is reverse keeping in mind the following:

Cleanliness counts where thermostat housing seals to engine.
Thermostat spring should point into engine.
If the thermostat has a bleed port, it should go to the 12 o'clock position (up).

Jan 03, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

My drive belt went on my 2006 civic and i want to replace it


loosen bolts on power steering pump 12mm and 14mm
should be 2-3 nuts, remove bolts(10mm) holding largw power steering hose to gain aeasier acess to alernator.
lossen alternator top bolt 14 0r 12mm lossen lower alternator bolt 17-19mm

Oct 20, 2009 | Honda Civic Cars & Trucks

2 Answers

Need to replace front turn signal bulb in 2003 A4


There's 2 bolts at the top f the unit which u need to take right out and 2 bolts at the back of the unit which are on a slide so only have to be loosened to slide the headlight out... then twist and pull the socket out of the assembly and change bulb.. reverse to put back on

Aug 12, 2009 | 2003 Audi A4 Cabriolet

2 Answers

Alternator repair 88 mercedes e class


Disconnect batt. Loosen belt tennsioner. Keep belt in place or mk note of belt routing. Remove bolt.Fan can stay on.

Dec 20, 2008 | 1988 Mercedes-Benz 300

1 Answer

03 elantra headlight assembly problem


ya easy job u can doo it three bolts 10mm two on top and one in the back down lower

Oct 07, 2008 | Hyundai Motor 2003 Elantra

Not finding what you are looking for?
Hyundai Motor 2003 Elantra Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

83083 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...