Question about 2000 Lincoln LS

1 Answer

Rear liscense plate bulb replacement

How do i replace them

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 235 Answers

Thare is little straight open slots on each side of the lens. put a small screwdriver in these slots to release the assembley then turn the socket out of lens ,the bulb pulls out

Posted on Feb 19, 2009

6 Suggested Answers

techbuster
  • 5081 Answers

SOURCE: 1999 Dodge Neon rear license Plate bulb

LICENSE PLATE LAMP BULB
REMOVAL

  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Posted on Oct 08, 2009

  • 196 Answers

SOURCE: 2000 Buick Lesabre custom liscense plate bulb

kind of tricky, took me an hour to get it figured out, but you got to opend the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together

Posted on Mar 20, 2010

  • 152 Answers

SOURCE: How do you replace the rear liscense plate lights

Look behind you bumper where the lights are installed. There should be a clip slipped over the back of the housing that holds the light into the bumper. 1 per light. Use some needlenose plyers or a screwdriver to push it off. The light sould pull out of the bumper from the other side. You can disconnect the harness is you wish or just replace the bulb. Whichever suits your fancy. After replacement put the holder back into the bumper and slip the clip back on behind it. 10 minute job.

Posted on Apr 08, 2010

  • 285 Answers

SOURCE: my liscense plate light in rear wont work, i tried

if the plate is on the trunk it will most likely be the wiring by the hinge of the trunk,the wires break sometimes after the trunk goes up and down a few thousand times,so just pull on the wires individually and see which one has a break in it and jsut solderit and heat shrink it...hope this helps

Posted on Oct 12, 2010

vetteman3002
  • 2299 Answers

SOURCE: How do you replace a

You will have to open the trunk to get to the plastic nuts that hold the carpet on. Remove several of the plastic fasteners holding the carpet to the inside of the lid. Gently force the carpet over the trunk latch assembly. Located under the carpet are ten (10) 10mm nuts holding the lamp assembly in place.
The whole light/license plate recess assembly will come off. You may want to replace ALL the bulbs now instead of later. Two each of: Sylvania 7528 (P21/5W), Sylvania 3157LL, and Sylvania 194LL.

Posted on Jan 24, 2011

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The fuse for the liscense plate light


is the same fuse for the tail lights
If you have tail lights then there is a wire in the bulb holder fault or a blown bulb

Dec 07, 2015 | Cars & Trucks

1 Answer

How to change liscense plate bulb


it`s very simple-- above lic. plate you will see the light lens. There may be 2 phillips screws, if there are just remove them and use a small flat head scewredriver to pop it open. Then remove the ``penut`` bulb. If there are no phillip screws, then use the flat head to pop the lens.
Also before you start lift the trunk open and see if you can access the bulbs from in there.
Good luck-it is very simple..

Feb 25, 2011 | 2003 Pontiac Sunfire

1 Answer

My liscense plate lights dont work


Replace the bulb, check for dirty contacts and bad ground connections.

Feb 18, 2011 | 1996 Oldsmobile Aurora

1 Answer

My liscense plate light in rear wont work, i tried the bulb and its not that, any idea besides my wireing messed up?


if the plate is on the trunk it will most likely be the wiring by the hinge of the trunk,the wires break sometimes after the trunk goes up and down a few thousand times,so just pull on the wires individually and see which one has a break in it and jsut solderit and heat shrink it...hope this helps

Oct 12, 2010 | 1997 Pontiac Sunfire

1 Answer

How do you replace the rear liscense plate lights


Look behind you bumper where the lights are installed. There should be a clip slipped over the back of the housing that holds the light into the bumper. 1 per light. Use some needlenose plyers or a screwdriver to push it off. The light sould pull out of the bumper from the other side. You can disconnect the harness is you wish or just replace the bulb. Whichever suits your fancy. After replacement put the holder back into the bumper and slip the clip back on behind it. 10 minute job.

Apr 06, 2010 | 1998 Ford Explorer

1 Answer

2000 Buick Lesabre custom liscense plate bulb


kind of tricky, took me an hour to get it figured out, but you got to opend the trunk and take out the 10 or so 10mm nuts sticking out of the backside of the lid, then the whole solid piece where the lights are on the back will slide off, then you can change the bulbs above the license plate and put it all back together

Mar 08, 2010 | 2000 Buick LeSabre

1 Answer

How to change liscense plate light? se model


hi, if your license plate bulb cover has no screw holes in it then the chances are its just pushed in it may be a very tight fit but should just pull out its usually held in by two plastic clips that lock once its pushed in so using a screw driver to lever the light cover off should get it off.

If you have a cover on the inside of the boot that covers the wires going to the number plate bulb you may be able to take this off and then be able to see how it comes off.

Let me know how you get on or if you need further assistance ok

Dec 28, 2009 | 1997 Nissan Pathfinder

1 Answer

How to replace 2004 cavalier headlight and liscense plate light


To replace headlight, open hood and there will be 2 -13mm bolts holding headlight, parking light and turn signal light. there is also a spring clip under bolts. bulb comes out from behind once you get the whole assembly out.
plate light is just below where it says chevrolet on the back bumper. There are two 7mm bolts holding it up in there, take out the bulb and take it with you so you get the right one. the headlight is 9007 halogen high/low. goodluck

Oct 29, 2009 | 2004 Chevrolet Cavalier

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

Not finding what you are looking for?
2000 Lincoln LS Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...