Question about 1995 Honda Civic

2 Answers

Check engine light comes on

I have a scanner but i dont know where to hook the cable up?

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Your car is obd 1 look on the passenger side by the cowl, that is by where your right knee would be. there are two connectors there the three pin is for the scanner and the two pin can be jumped(put a little wire connecting the two holes) and the engine light will blink. long blinks before short blinks will tell you what code number it is the two connectors might be in a blue rubber casing that only both plug into.

Posted on Dec 25, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is under the dash under the steering wheel

Posted on Dec 18, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My jeep keeps stalling on me and the check engine light never comes on, people tell me it may be the fuel pump. i have been told it cant be hooked to compuetr because of the check engine light not com

A stalling problem doesn't have to turn on the check engine light . Try some basic thing's like cleaning the throttle plate (body) air passages for the IAC - idle air control valve . There are videos on youtube , also check for a vacuum leak !

Cleaning Throttle Bodies
Throttle Body Cleaning To Restore Idle Quality

May 17, 2017 | 1997 Jeep Grand Cherokee

1 Answer

What fuse number for the diagnosis plug to get the check light engine

fuse number 24 is a 30 amp fuse goes to pcm relay and fuse number 30 the 30 amp fuse to ignition to pcm power diode.if check light is working your pcm has power but you could have short in the dlc connector terminal where you scanner adapter goes.your scanner suppose power up from the dlc terminal for obd 2 system the obd 1 you connect to cigarette light or use battery hook up cables that come with scanner make sure you are using correct adapter.

Nov 15, 2011 | 2000 Ford Expedition

4 Answers

How do you reset the check engine light on a 2007 mitsibishi galant?

You hook up a code scanner and press the reset code function or you can disconnect and reconnect your battery. If there is something which is at fault after codes are cleared engine light will come back on and you should get codes checked. Most parts stores will check for you for free but their level of mechanical expertise can very drastically so check back here with trouble codes which you can't determine for further help

Apr 28, 2011 | Mitsubishi Galant Cars & Trucks

2 Answers

My check engine light came on and i dont know what the problem is. It jus had a recent oil change and runs great. I tightened my gas cap to see if that was the problem but the light is still on.What else...

When the check engine light comes on the computer has detected a problem. there are too many things that can make the light come on to make a guess on the internet. You need an OBD II scanner to retrieve the code(s) and that will allow you to make a repair decision. In some areas your auto parts store will read the codes for free.

Mar 07, 2011 | 2001 Kia Rio

1 Answer

No check engine light. When hooking up mac scanner it says hook up scanner. Engine missing bad. No check engine light when unplugging sensors.

I don't quite understand your predicament. Where "Hook up scanner" displayed? What sensor did you unplugged expecting for a check engine light to come on? Please give more information in order understand and advice a solution if it's truly an engine misfire and not un-metered air passing into the intake system. More vehicle information would help, it's difficult not being part of the population that are psychic.

Jun 21, 2010 | Cars & Trucks

1 Answer

My 2003 saturn vue service ebgine light stays

The CEL (Check Engine Light) will not go out until you hook up a OBD II scanner to your vehicle and erase the code. If it comes back again after you erase it than either the original problem still exists or you have a new problem. You can go to your local AutoZone store and they can hook up a scanner and erase your code for free.

Jun 05, 2010 | 2003 Saturn VUE

1 Answer

1991 GMC, sevice engine light turns on and off intermittently, scanner shows no commuication with PCM, tried new PCM still has problem. I have checked all fuses.

try un hooking a battery cable and it will usually reset them if u dont have any problem it should go off, but usually if it comes back on there will be a problem somewhere might just be a sensor, sensor are one of the main reasons y the engine light turns on. just take it to auto zone or something and they can tell u y the light keeps coming off if, that other solution doesnt work

Mar 31, 2010 | 1991 GMC C1500

1 Answer

My check engine light came on shortly after filling my car with gas. I tightened the gas cap, now how do I reset the Check Engine light?

Well in the newer cars you cant have the car running when filling the tank.

Take it to either advance auto or autozone and they will have a scanner. Tell them you dont know what the code is. Watch how they hook it up.

They will let you borrow it, but for what they say are "liability reasons" they wont clear your codes. Just hook it up and use the scanner. Really easy, menu driven device. And it will save you a bundle compared to what the dealer wants I'm sure.

Dec 22, 2009 | 2005 Subaru Outback

1 Answer

Check engine light will not stay off after reset etc very long..n

cause there is more than likely a code set in the vehicle. Check engine lights dont just come on cause they want to. Just because the light comes on doesnt mean there is something bad rong. My step dads truck has had the check engine light on for 3 years, its been cleared several times only to come back on again to... turns out it just has some stupid sensors bad but they dont affect the running condition of the vehicle. Take it to autozone, ask them to hook up scanner and go from there

Jul 02, 2009 | 1999 Isuzu Trooper

1 Answer

My daughter put midgrade gas on my 2003 audi a4 quattro 6 3.0

it could cause the check engine light to come on if the motor had a ping. and you should put the premium in it. but the only way to konw for sure on what set off the check engine light is to hook it up to a diagnostic scanner. and that will tell you for sure and you will have to hook it up to a scanner to shut the light off also

Apr 29, 2009 | 2003 Audi A4 Cabriolet

Not finding what you are looking for?
1995 Honda Civic Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

81424 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides