Question about 2006 Ford Ranger

Open Question

Installation of passanger side window washer fluid jet

The jet was damaged. After looking under the hood the drivers side tubing is exposed the passanger side is behind the engine compartment. Will I have to remove the dash to install?

Posted by on

  • 1 more comment 
  • silver top May 11, 2010

    hi the washer jet itself has two plastic clips each side which spring out when jet is pushed into its hole/location so to remove use a small screwdriver and prise under one side of jet whilst lifting you will find jet will come out of its location with pipe attached disconnect pipe and have someone operat washer if pipe is clear or blocked advise you wrap some tape or a wire tie round pipe 1st so as not to lose it inside ?

  • Jeremy Kastrup May 11, 2010

    windshield washer squirters ?

  • Brian  Greer
    Brian Greer May 11, 2010




2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 87 Answers

SOURCE: Hi - The jet for

no you will have to remove the wiper cowl , remove the wiper arms and any exposed clips holding the cowl down , sometime ford used Blind clips so it may feel attached after you remove any exposed screws . BE careful around the windshield !!!

Posted on Dec 18, 2008


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Landrover Discovery 300tdi 1997 Windscreen Washer Diagram

Hello! The rear washer tubing runs from the reservoir up thru the front corner support column, thru the roof and over to the door. The tubing run from the reservoir to rear door washer jet differs between left and right hand drive vehicles. On right hand vehicles the tubing run is on the left hand side of the roof. On left hand drive vehicles, the right side.

Normally, there is always fluid present in the tubing, thus no priming is necessary and it prevents any clogging... The rear washer jet is is more than likely plugged... Guru...saailer

May 06, 2012 | Cars & Trucks

2 Answers

After a hard freeze my window washer stopped working. It barly drizzles out of the jets but under no pressure. Will I need to replace the pump or is there a screen or diaphram that can be repaired

Most likely the tubing between the pump and jets ruptured when the fluid froze. Have someone hold the spray lever/button while you follow the tubing from the jets down to the pump and check for leaks. Some of the tubing may run in the fender well and you will have to remove the plastic fender well lining above and behind the wheel to access it. It is possible that the pump was damaged by the freeze, but damage to the tubing is much more likely. Good luck, I hope this helps.

Mar 12, 2011 | 2008 Dodge Dakota

1 Answer

Wiper fluid comes out only on driver side when trying to clean window. Is there some sort of manifold or solenoid valves that dispense the fluid to each side. Also when trying to clean rear window no...

Look at the fluid canister, You will see a hose that leads to the hood and splits to the right and left. The hose that leads to the pass. side could be clogged up or the fluid jet that fluid comes from could be clogged up. Disconnect the hose from the pass side jet, and see if fluid comes out when turning on. If so, then the jet is the problem. These can be bought from a parts store, but will not be OEM. the front and back are controlled with one pump, which I don't think is the problem. The rear may be the same problem, try doing the same as you do for the front. Sometimes the car wash soap you use or wax can build up and block the jet hole up.

Jun 13, 2010 | 2003 GMC Yukon XL

2 Answers

I have a 1998 chrysler concord and i can get windsheild washer fluid to spray the resevoir is full no fluid is leaking out the wipers activate upon initiating the spray sequence but no fluid comes out

Pull out the small tube connected to the jet the fluid comes out of and check for any kind of debris, after blowing out the tube try and activate washer before you connect the hose again if no fluid comes out of the tube than that replace the small pump connected to the resivoir thay are about $15.00

Nov 29, 2009 | 1998 Chrysler Concorde

2 Answers

WIper fluid does not flow

Hi Curran

Usual problem is that the jets nozzles become blocked.

Get a small sewing needle, and clear the jet, preferably when a friend operates the washers.

If this is not successful you will need to pull the feed hose off the jet body, and once again operate to check for blockage or a kinked pipe.

Good Luck !


Jan 16, 2009 | 2001 BMW 330

2 Answers

1999 ford taurus the front window washers won't spray

lift the hood and remove one of the tubs try press then if you have water the jets are blocked.

Dec 28, 2008 | 1999 Ford Taurus

1 Answer

Hi - The jet for the window washer fluid on the passanger side was damaged. I bought a replacement part (2L5Z017603-AA) Kit-Jet. The driver side tubing is exposed within the engine compartment, the...

no you will have to remove the wiper cowl , remove the wiper arms and any exposed clips holding the cowl down , sometime ford used Blind clips so it may feel attached after you remove any exposed screws . BE careful around the windshield !!!

Dec 18, 2008 | 2006 Ford Ranger

2 Answers

Washer fluid and a sticky unlock on back door

check the fuse for the washer pump first.

Jul 04, 2008 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
2006 Ford Ranger Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5655 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides