Question about 2004 Mitsubishi Endeavor

Open Question

Wheel bearing torque specifications

I need the torque specs for the rear wheel bearings on a 2004 Mitsubihi Endeavor.

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 44 Answers

SOURCE: need diagrams to show how

You might try you local library, You should be able to find a book on your make and model, that will have the instruction in it you need to do the job.

Posted on Nov 01, 2008

  • 1 Answer


just did one today. removed housing from car, and used a press . be careful of aluminum housing. also used penatrating spray. clean oxidation from inside bearing hole,then lubricating, helped in installation

Posted on Dec 28, 2008

  • 34 Answers

SOURCE: torque settings for wheel bearing

120Nm on all A3s with standard wheels.

Posted on Jan 22, 2009

  • 5158 Answers

SOURCE: change front wheel bearing

this is a pretty good guide on bearing replacement for your car

Please take a moment to rate this solution

Posted on Feb 02, 2009

  • 2 Answers

SOURCE: how to change rear wheel beqarings in a 2000

pretty simple they have rotors like front so remove caliper and rotor. make sure rotor is clean when u put new seal and bearings in. also hand pack wheel bearings with grease.

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

Main bearing torque specs

Here are all of the torque specs on 2004 Endeavor



Feb 03, 2015 | 2004 Mitsubishi Endeavor

3 Answers

Torque specifications 2000 chevy impala wheel bearing

The 2000 Chevroleticon1.png Impala is a sedan available in a pair of different versions, the base model and the LS. The Impala's torque specifications depend on the model, as the base and LS have different engines

Read more :

Oct 11, 2014 | 2000 Chevrolet Impala

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually

The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

What are mazda 6 wheel bearing torque specification

What is the front axle torque on a 2004 Mazda 6

Mar 17, 2012 | 2004 Mazda 6

1 Answer

Need to know the torque setting for the rear weel bearing on my 2001 ford focus. it takes a 30mm socket.

The torque setting 49 ft. lbs.

Torque Specifications
Description Nm lb-ft lb-in Wheel nuts - steel/alloy wheels 128 94 - Wheel spindle retaining nuts 66 49 - Wheel cylinder retaining bolts 12 9 - Rear brake pipe to wheel cylinder union 8 - 71 Rear wheel speed sensor retaining bolt 9 - 80 e0001241.jpg
Item Part Number Description 1 - Tie bar and knuckle 2 - Backing plate 3 - Wheel spindle 4 - Sensor ring - anti-lock control 5 - Grease cap 6 - Wheel bearing retainer 7 - Drum

Apr 26, 2011 | Ford Focus Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd

4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal

      Inner wheel bearing removal-rear hub/bearing

      Rear wheel bearing removal-2wd

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable

    Rear wheel bearing installation
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best

A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

Proper torque for bolts on front wheel

The axle nut spec is 177 foot lbs. and the bearing to knuckle bolts spec is 133 foot lbs.

Dec 23, 2009 | 2004 GMC Yukon

1 Answer

I need the torque spec for the axle and the axle nut for the front wheel bearing. 2004 gmc yukon 4.8 ltr. 4wd.thank you

Go to the website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Aug 17, 2009 | 2004 GMC Yukon

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8830 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides