Question about 2003 Chevrolet Express

1 Answer

Rt front turn sighal burned out - how to access bulb to replace

Turn signal
how do you change front turn signal bulb

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

There is a latch to the Van's outside just insert a flat blade screw driver and the turn light assembly will swing toward the middle of the van.

Once open the lamps twist out.

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lf rear turn signal not working. LF front, RT front & rear working. Replaced with 3 new bulbs but no joy. What would cause one blinker to not work?


This could be a fuse so check them all, next make sure you are not missing a burned out light or have the wrong bulbs in.

Replace the flasher unit, make sure the connections in each socket is clean, make sure the wires are in good order.

Also the switch control might be at fault.
hope this helps.

Mar 18, 2015 | Cars & Trucks

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

1 Answer

Turn signal flashes fast but bulbs good


You need to replace the turn signal flasher with a heavy duty one.

Oct 19, 2013 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

1998 pontiac transport/montana has not tail or break lights...turn signals blink fast or not at all. changed rear bulbs and noticed carbon on front build up on front bulbs. Help!


If one of the filaments in the bulbs is burned out, the remaining working lights will flash alot quicker.
Check the bulbs, and replace if the filaments are broken.
If the front bulb has a carbon build up it blown out...change it..
Once the bulbs are replaced your signals should work properly.

Dec 09, 2009 | Pontiac Trans Sport Cars & Trucks

1 Answer

Please tell me how to replace a burned out head light, high beam.


To replace the headlamp, turn signal, or parking lamp bulb:This information should be in your owner's manual.
Turn the wheel to access the wheel well.
  1. Remove the fasteners located on the wheel liner. To access the headlamp and the turn signal/parking lamp bulbs.
  2. Reach in behind the wheel well liner and locate the bulb to be changed.
  3. Turn the bulb socket counterclockwise and pull it straight out of the lamp assembly.
  4. Pull the old bulb straight out of the bulb socket.
  5. Push the new bulb straight into the bulb socket until it clicks.
  6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place.
  7. Reinstall the wheel well liner using fasteners.

Nov 11, 2009 | 2006 Chevrolet HHR

1 Answer

Replace rt. front turn signal bulb


look at the other side,under the bumper you just twist and turn and you will have access to change your bulb.

Aug 09, 2009 | 1999 Chevrolet Cavalier

1 Answer

Signal light bulb change/who and where


  1. From under front wheelhouse, remove access cover behind park and turn signal lamp
  2. Through access hole in wheelhouse, rotate park and turn signal socket counterclockwise one quarter turn.
    1. Pull socket from back of lamp.
    2. Pull bulb from socket. INSTALLATION
      1. Align key on bulb base to groove in socket and insert bulb into socket.
      2. Through access hole in wheelhouse, insert socket into back of lamp.
      3. Rotate park and turn signal socket clockwise one quarter turn.
      4. Install access cover and verify lamp operation.
Hope this helps with your prob

Mar 27, 2009 | 1998 Plymouth Voyager

2 Answers

Replace front driver signal light bulb


Depending on whether it is the front or the back turn indicator light will determine on what needs to be done. If it is the front turn indicator light open the hood of the car you may need to take the entire headlight out. The headlight may have screws, take the screws out then the front light will come out from the outside of the vehicle replace the burned out bulb. The bulb should snap right in and then put the headlight back in make sure you put all screws back in from the inside of the hood. Step2 If it is the back turn indicator light, go through the trunk of the vehicle. If there is a panel covering the lights you must unscrew the panel and then replace the burned out light bulb. Some panels can be folded down without removing all of the screws to access the lights. This light may not require for you to pop the entire light out you maybe able to just replace the bulb. After you have replaced it screw the panel back into place. The back light should not require the entire light to be lifted out just a simple bulb replacement. Step3 In replacing either the front or the back indicator light you must gain access to the turn signal housing which is usually in the same case as the headlight or your rear lights. It is very helpful to also get the owners manual out this will tell you exactly what type of bulbs you will need to get to replace the indicator bulb.

May 29, 2008 | 2005 Cadillac SRX

Not finding what you are looking for?
2003 Chevrolet Express Logo

474 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...