How to get the five digit code from your vin number

Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the owner literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit mst be entered within five seconds of the previous button press.

Do you know the original five-digit code ? You need the original to reset with a new one .

Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:

1. Enter the factory set five-digit code (the keypad will illuminate when pressed).

1. Press 1/2 within five seconds of Step 1.

1. Enter the unique five-digit code.

The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it overwrites the previous personal code. To erase a personal code, carry out the following procedure:

1. Enter factory set five-digit code.

1. Press 1/2 within five seconds of Step 1.

1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.

The system now responds only to the factory set code.
If you do not know the code ,it is located on the vehicle security module located under the dash some where or in the trunk . Sorry I can't be more specific ,my service info doesn't show sable .

Enter the five-digit code programmed into the keypad from the factory. Find the key code in the card stored in the glove box of your Mariner.

Press the "1-2" button on the keypad immediately after inputting the factory code.

Enter the five-digit key code you wish to store for your keyless entry system within five seconds of pressing the "1-2" button.

Read more : http://www.ehow.com/how_7442543_program-entry-pad-mercury-mariner.html

Not in the vehicle

It may be avail from the dealers parts dept,
if you give them your VIN #

It came with the vehicle when new,the factory code
that is,was on a white plastic card on some fords,then
you can change it ,if you have the owners manual

need to notify dealer for original code have vin and proof of ownership of vehicle available

you need locksmith or dealership you will need vechicle VIN NUMBER.located on a plate on top of dash visible through windshield.

Location of Keyless Code on Computer Module of Ford F250 Superduty ( 2009 )

Finding this code seems to be a common problem, so, here is a better answer to save you the time I spent locating the sticker on the computer module that shows the keyless entry code.

One owners from 2008 F150 XLT Superduty tell me and I suspect the location for a F150 would be very near same location as on a F250

The computer module is mounted high on the firewall approximately behind the a/c fan speed control knob. Here is how to find it / get to it:

1. Remove the large cover under the steering column that covers the fuse block. You'll need to reach in under the dash, with your left arm, to the right of the steering column and left of center to move stuff to get a clear view.

2. Open the storage pocket door on the lower edge of the dash (right of the steering column) and squeeze the back side of the storage pocket to allow the stops to pass to the front. This will allow the opening to be clear to see the computer module up in the dash. Shine your flash light through this opening.

3. Move the first piece of white insulation to the side to see the firewall. Look up through the pocket door, moving the wiring harnesses aside if necessary. You'll find a second white insulation wrapped snugly across the computer module. When you push the insulation up to see the flat surface, you see the 5 digit number printed up-side-down in black on a white sticker. This is your keyless entry code.

Instructions for Programming Keyless Entry Code (from the 2008 Owner's Manual)

KEYLESS ENTRY SYSTEM (IF EQUIPPED)
You can use the keyless entry keypad to lock or unlock the doors without using a key.

The keypad can be operated with the factory set 5-digit entry code; this code is located on the owner's wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5-digit personal entry code.

When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Programming a personal entry code
To create your own personal entry code:
1. Enter the factory set code. The driver door will unlock.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other.

4. The doors will lock then unlock to confirm that your personal keycode has been programmed into the module.

Tips:
• Do not set a code that uses five of the same number.
• Do not use five numbers in sequential order.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

u need to give VIN number to your dealer or directly to FORD. THEY can instantly give u the key details.

Location of Keyless Code on Computer Module of Ford F250 Superduty ( 2009 )

Finding this code seems to be a common problem, so, here is a better answer to save you the time I spent locating the sticker on the computer module that shows the keyless entry code.

One owners from 2008 F150 XLT Superduty tell me and I suspect the location for a F150 would be very near same location as on a F250

The computer module is mounted high on the firewall approximately behind the a/c fan speed control knob. Here is how to find it / get to it:

1. Remove the large cover under the steering column that covers the fuse block. You'll need to reach in under the dash, with your left arm, to the right of the steering column and left of center to move stuff to get a clear view.

2. Open the storage pocket door on the lower edge of the dash (right of the steering column) and squeeze the back side of the storage pocket to allow the stops to pass to the front. This will allow the opening to be clear to see the computer module up in the dash. Shine your flash light through this opening.

3. Move the first piece of white insulation to the side to see the firewall. Look up through the pocket door, moving the wiring harnesses aside if necessary. You'll find a second white insulation wrapped snugly across the computer module. When you push the insulation up to see the flat surface, you see the 5 digit number printed up-side-down in black on a white sticker. This is your keyless entry code.

Instructions for Programming Keyless Entry Code (from the 2008 Owner's Manual)

KEYLESS ENTRY SYSTEM (IF EQUIPPED)
You can use the keyless entry keypad to lock or unlock the doors without using a key.

The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code.

When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Programming a personal entry code
To create your own personal entry code:
1. Enter the factory set code. The driver door will unlock.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other.

4. The doors will lock then unlock to confirm that your personal keycode has been programmed into the module.

Tips:
• Do not set a code that uses five of the same number.
• Do not use five numbers in sequential order.


Good Luck (remember comment and rated this).

The Remote Keyless Entry (RKE) Module is located between the Junction Block and Body Control Module.
THIS CAR COME WITH 4 DIFERENT ENGINES SAME ENGINE SIZE BUT DIFERENT INJECTION SYSTEM THIS information is for a 3.5 vin (G ) the engine vin code is on the vehicle identification number and is the 8th digit from left to right

The keyless entry module is located in the rear of the vehicle on the driver's side. You will need to partially remove the left rear panel in the cargo area. You will then see the keyless entry module bolted behind a metal reinforcement bar. There is a sticker on the module that has the 5 digit entry code.