Question about 2005 Nissan Altima

2 Answers

CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA

WERE IS CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA AND HOW to get to it?

Posted by on

  • 2 more comments 
  • Anonymous Mar 14, 2014

    where is the crank shaft position sensor located

  • Anonymous Mar 18, 2014

    replacement of the crank position sensor, 2400 engine,m12 valve, 4 cyl

  • Anonymous Mar 18, 2014

    how do I replace the crank position sensor on my 1992 Nissan Stanza 2400 12 valve 4 cylinder vehicle?

  • Anonymous Mar 30, 2014

    code p1148 como cambiar la parte

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Nissan Master
  • 383 Answers

1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Posted on Apr 06, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Locate the crank shaft position sensor SLK230

Posted on Jan 06, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 nissan altima po340


PO345 is the cam shaft positioning sensor and PO325 is the knock sensor. Check your starter and your battery.

Apr 05, 2014 | 1995 Nissan Altima

1 Answer

Location of crank shaft position sensor on 2006 nissan altima


its on the back side of the engine near the bell housing there was a factory recall on some of those

Sep 22, 2012 | 2005 Nissan Altima

1 Answer

Where is the crank positioning sensor


I does not have a crank position sensor. It uses a cam sensor located in the bottom of the distributor. Sometimes the seal will fail on the internal shaft and the vehicle will not start. Replace the distributor and it will work if that is your problem.

Dec 09, 2009 | 1994 Nissan Altima

3 Answers

Crank position sensor for 2003 Nissan Altima


a crank position sensor , sends a signal to pcm about crankshaft position signal, the sensor controls spark timing and firing order. the signal is also used for pcm to detect a missfire!! it also sends this info to ignition module, any mechanic can replace a crankshaft sensor!! call a auto parts store and see if you can get one, the cost should be a lot less.

Sep 01, 2009 | 2005 Nissan Altima

1 Answer

2004 Nissan Altima crank positioning sensor


driver side under water outlet (upper water outlet ) good luck

Jun 03, 2009 | 2004 Nissan Altima

1 Answer

Where crank shaft and camshaft?


The camshaft position sensor is located on the timing cover, near the top of the motor. The crankshaft position sensor is located on the same timing cover near the crankshaft. Just a side note, more than likely the crankshaft position is your issue and it's under a recall from Nissan and they will replace it for free.

May 23, 2009 | 2002 Nissan Altima

4 Answers

Crank shaft sensor


I have 10 years experience in a Nissan dealership and I know without a shadow of a doubt that the Crankshaft Position Sensor is NOT located next tp the crank pulley... it is rather at the other end of the engine near where the transmission bellhousing bolts to the engine block. It is on the side toward the firewall near the bottom. Even if you can get the vehicle on a lift and get under it, you can't really see it... It's more of a feel thing... There was a campaign (recall) on these engines to replace Crank Position and also Cam Postion sensors. Check with your dealer- the campaign might be open. You will need your VIN number when you call.

Oct 23, 2008 | 2003 Nissan Altima

1 Answer

2003 altima nissan


HI. I read your problem.
Let me ask you,
The sensor that you are installed are from the dealer or aftermarket?
Because the crank sensor on a 02 to 06. altimas where defectives. or damaged to fast.
Is why NIssan company Made a complety diferent new sensor.
Trying to resolve this problem.
If you haven't get from the dealer, I recomment get one from them. When you see the connector on inverter position don't worry it will fit.
But if you install from the dealer. I recoment check the engine for high vibration.
Check the crankshaft for end play.
And check the wires from the sensor for short, or burned shield.

OK> I hope this work for you..
I have changed few of them..

Jul 14, 2008 | 2003 Nissan Altima

Not finding what you are looking for?
2005 Nissan Altima Logo

1,787 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...