- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
to remove door trim you have to disconnect negative battery cable.then remove two screws attaching arm rest to door trim.remove arm rest it held in place by front and rear hooks that fit into slots in door trim.to release the hooks grasp the arm rest with both hands push it towards thr door pull up on the side of the arm rest facing door.remove four speaker grille mounting screws and the grille.then remove door trim panel screwss from bottom edge of the panel.remove the three remote control plate screws from the plate and the single screw in the rear edge of the door.then lift up on the door trim panel to release the molding from the top edge of the door then slide the panel forward to clear the latch release handle and down to clear the lock rod knob.if job look to difficult let a body shop fix.removing window door motor need tools to drill out rivets and reinstall rivots you need special tools to fix window motor and regulator.
Once you get the door panel off you can easily see how to remove the window which is riveted to the window regulator..Here are instructions for determining the rear door in a Taurus.
Pluck the window switch and lock switch from the rear door panel with the trim tool. Pull the wiring plugs out of each switch manually before setting the switches aside.
2Remove the rear door panel retaining screws with either the Phillips screwdriver or socket set, depending on the year, make and model of your vehicle. If the panel will not lift off the rear door at this time, you may need to pry the door panel trim pins out of the door with the trim tool before removing the panel by hand. (This too will depend on the year, make and model of your vehicle.)
3Raise the rear door window glass by hand and secure it with packing tape in the fully upright position to prevent unintended glass movement. Manually pull the wiring plug out of the rear window motor.
4Remove the rear window motor retaining bolts with the socket set. Pull the old rear window motor out of the door through the door access hole. Position the new rear window motor in the door and bolt it in place with the socket set.
5Reinstall the rear door panel on the rear door by reversing the door panel removal steps. Make sure to remove the tape from the window when done before you attempt to open the window.
They are not related ...
The lift gate locking mechanism can be accessed by removing the interir trim pannel on the gate ... and locating the locking actuator and replacing it...
The same can be done for the power window motor ... remove the interior trim panel and replace the power window motor...
It sounds like your motor is dying. It take no effort for the motor to allow the window to fall down with gravity, but a lot harder to lift the window back up....
on the inside trim, you can remove screws that are by the door handle,
arm rest, under door and side of door and then gently pull back on the
panel as there will also be retaining clips attached and you don't want
to break them. You'll need to lift the door panel upwards in order to
get it off the window ledge.
after u remove the bolts that hold it to the window regulator tip the window towards the front of the door and the top rear corner of the window should pop out and then u just lift hte window out,hope this helps
Remove the rear door trim panel and watershield. Refer to Section 01-05B .
Trim Panel, Rear Door, Explorer, Hi-Series Four-Door
Removal and Installation
Remove the two screws retaining the rear door trim panel (27406) located above the door handle.
Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.
Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .
From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .
At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.
Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip.
For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
If equipped with power windows, disconnect the wire from the regulator.
Remove the rear door window glass as described in this section.
Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.
Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet.
NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
Using a 1/4-inch diameter drill, drill out the remainder of the rivet.
Remove two upper regulator attaching nuts.
Remove regulator from the front door (20125) .
Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.
Install regulator into access hole in inner panel.
Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).
Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).
Install two upper regulator attachment nuts.
Install door glass as outlined under Door Glass Installation.
Adjust glass as outlined under Adjustments .
Reconnect wire to regulator, if equipped.
Check operation of window regulator.
Install door watershield and trim panel. Refer to Section 01-05B .
SECTION 501-05: Interior Trim and Ornamentation
2000 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION
Rear Door Trim Panel
Removal and Installation
Remove the rear door trim panel screws.
NOTE: The rear door trim panel has eight two-part pin-type retainers. The male part of the retainer will remain with the trim panel and the female part will remain with the door. NOTE: To release the door trim panel pin-type retainers, first pull outward on the bottom of the door trim panel. Remove the rear door trim panel.
Disconnect the window regulator control switch electrical connector.
Remove the rear pivot arm; refer to Pivot Arm—Rear .
Remove rear pivot arm.
Lift the pivot arm nut cover.
Remove the nut.
Remove the pivot arm.
Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
Remove the liftgate door trim panel.
Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel.
Position the watershield aside to gain access to the rear wiper motor.