Question about Mitsubishi Outlander

Open Question

Vibration or "washboard effect" after letting go of accelerator between 45 and 70mph

Posted by on

  • pshaw1313 Mar 18, 2009

    We were told to have the inner tie rod ends replaced; dealer cost plus parts approximately $700.00.



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is causing my 4 cylinder 318i BMW to vibrate or tremble when I put it in drive or reverse. Once it is in park it seems to be fine or if I turn on the AC it trembling minimize also when I accelera

Possible broken motor mount or torque strut. Your engine is probably rocking too far when it is put into gear. The torque strut will prevent that. The rubber bushing n the strut is probably bad.

Jun 22, 2014 | 1998 BMW 318i Automatic

2 Answers

Vibration when accelerating and at high speeds

could be a few things engine mounts gearbox mounts cv joints on prop shaft flex disks if it has any could be missing when under heavy load there are many things i have somthing similer on my mercedes think its the flex disks hope this helps

Aug 18, 2012 | 2005 Ford Escape

1 Answer

Mazda cx9 vibration

Raise the vehicle off the ground, wiggle front tires left and right, excessive play tells you tie rods, up and down tells the wheel bearing condition, but have another set of eyes looking on the inside while wiggling tires, too see excessive play. Lower ball joint can be seen during this test. And make sure wheel spins freely, siezed brake calipers can make higher speeds shake too. Lastly look at centre drive shaft condition. Hope this solves thr mystery. HTV Auto Body

Jul 13, 2012 | Mazda CX-9 Cars & Trucks

1 Answer

Vibration while accelerating

it indicates a problem in the drive lines possible cv or "U" joints failing

Jun 06, 2017 | Chrysler Town & Country Cars & Trucks

1 Answer

When i accelerate on my 2004 ford explorer the car vibrate, the more i accelerate the vibration increase. This is not comfortable driving with this vibration. please help.

check for play in the driveline universal joints. If there is play, replace joint. Let us know if you need DIY instructions.

Oct 16, 2010 | 2004 Ford Explorer

5 Answers

My 1994 toyota camry has the shakes

most likey the tires need to be balanced

Mar 31, 2009 | 1994 Toyota Camry

1 Answer

Vibration when accelerating

You may need to have tyres balanced and wheel alignment done.

Dec 14, 2008 | 2005 Toyota Tacoma

1 Answer

Vibration in 1998 town car

The transmission in your car is the 4R70W model,and i've rebuilt hundreds of them through the decades,and the vibration you are likely feeling is in the torque convertor.I call it the "washboard effect",or at least that's what it feels like,running over an old timey washboard,and it can also be described as a shuddering sensation,or chattering.Inside the torque convertor is a clutch that engages to eliminate fluid slippage within the convertor,thus making it more efficient,resulting in better fuel mileage.This clutch becomes weak and slips,and that is what is felt.In most cases,the vibration is felt at speeds of 40 mph and higher.Ford and Lincoln dealers have a Technical Service Bulletin (TSB) out about this,and they advise changing the fluid by dropping the pan,and pulling the drain plug in the torque convertor,changing the fluid to a Ford specification fluid,and adding a highly friction modified supplement to the fluid to prevent the washboarding.In most cases,it solves the problem,but in some cases the torque convertor must be replaced.Good luck

Aug 30, 2008 | 1998 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8830 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides