Question about 2005 Dodge Caravan

2 Answers

Windshield wash will not work

The battery was unhooked from the van and now the windshield washer will not work. According to the manual there is a module that needs to be reset if it does not work. Is this something that i can do myself? It is a 2000 dodge caravan 4cyln. If it is something that i can do myself i need to know where the module is and how to reset it.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 37 Answers

There's no module. There's a pump at the resovor and a fuse. Check all fuses. May have a fuse marked windshield wiper check that fuse. If not that check pump may be a bad pump or it is clogged up.

Posted on Oct 27, 2017

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 120 Answers

You need to post the type of vehicle before I can answer your problem

Posted on Oct 27, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

INSIGHTAEM
  • 2 Answers

SOURCE: starter for dodge caravan 2000

DISCONNECT THE BATTERY, JACK UP AND SUPPORT YOUR CARAVAN. LYING ON YOUR BACK LOCATE THE STARTER WHICH IS ATTACHED TO THE ENGINE THROUGH THE BELL HOUSING .THERE ARE TWO 15 MILIMETER BOLTS THAT HOLDS THE STARTER ON . AFTER BREAKING THE BOLTS A 15MM WRENCH WOULD BE USEFUL.

Posted on May 30, 2008

  • 548 Answers

SOURCE: dodge caravan sliding doors

First, keep in mind that as you begin to remove these doors you run the risk of causing serious scratches to the paint and glass, so put some masking tape and/or plastic sheeting around both sides of the door (rear quarter panel and rear glass, front door and front door glass)
I would get a Haynes repair guide since that's what I have to work from and it will tell you step by step with pictures, what to do. It's not hard, but you need to get all of the attach points unhooked to be successful. Suggest you have a helper working with you to keep the door steady.

Posted on Jan 25, 2009

freetek
  • 5568 Answers

SOURCE: 2002 Dodge Caravan Windshield Washer

If the pump still makes noise, you may just have clogged nozzles, have you tried those yet? Also, if you have windshield cleaner left over from summer, it may have frozen in the lines. 

Posted on Jan 26, 2009

  • 548 Answers

SOURCE: replace broken fuel door 2000 dodge caravan

If you're on the smallish side and pretty limber, you might avoid removing the rear wheel. If not, you will likely need to remove the rear wheel and put the van on jack stands securely. I would remove the underside splash shield and gain access from underneath. It looks like you will need to unscrew the plastic insert that surrounds the filler neck inside the area that is exposed when you open the fuel door. Make sure you get the vent hooked up correctly when you are done.

Posted on Jan 31, 2009

  • 285 Answers

SOURCE: removing/installing 2000 dodge grand caravan window glass

after u remove the bolts that hold it to the window regulator tip the window towards the front of the door and the top rear corner of the window should pop out and then u just lift hte window out,hope this helps

Posted on Sep 05, 2009

Testimonial: "Thank you!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers will not turn on 2006 colorado


There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

Oct 06, 2017 | Cars & Trucks

1 Answer

When I turn the switch to my 2006 Cadillac DeVille CTS windshield wiper it does nothing no sound no movement what is wrong


Hard to say what's wrong without testing thing's . Is there B+ voltage to the wiper switch ? B + voltage to the wiper motor ? Do you know how to use a voltmeter ? How to test electrical circuits ?
Here is a factory service manual list of componets involved .
Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Do you know how the wipers work ?
Windshield Wiper Motor Wiring Tutorial
Wipers Inoperative - All Modes ?????
Wiper Motor Switch Troubleshooting

Sep 05, 2017 | Cadillac Cars & Trucks

1 Answer

How do I find out if the wipers on my 2006 H3 Hummeris on a relay?


The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit, and energizes the wiper micro relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool, by commanding Wiper Relay Cmd. ON and OFF. Refer to Scan Tool Output Controls .
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper micro relay and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During high speed wiper motor operation the wiper switch signal circuit is at the low speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

This info is out of hummer factory service manual !

Dec 10, 2016 | 2006 Hummer H3

1 Answer

Which fuse controls front windshield wiper pump


Do the wipers work ? Fuse for wipers is same as washer pump .
Principles of Operation
The wiper motors receive inputs from the following:
  • Multi-function switch
  • Powertrain control module (PCM)
  • Ignition switch
  • Smart junction box (SJB)
The following components are integrated in the wiper motors:
  • Windshield wiper motor module
  • High/low speed relay
  • Run/park relay
  • Washer pump relay
  • Park sense (Hall-effect sensor)
Washer System
The windshield washer and the rear window washer are activated by the internal wiper motor modules when it receives a ground from the multi-function switch between the washer inputs. Depending on the correct ground, the internal wiper motor modules activate either the windshield washer or rear window washer relays (internal) by grounding the respective relay coil. When either module is activated, it connects voltage to the washer pump while the deactivated module provides ground to the washer pump. In this manner, voltage polarity is reversible to achieve directional change of the washer pump and washer fluid.
  • The washer pump is inoperative
  • Circuitry
  • Washer pump
  • Multi-function switch
  • Windshield wiper motor
  • Rear window wiper motor
  • Go To Pinpoint Test I .
Does your expedition have programmable/recall memory option for seats an mirrors ?
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
On the Expedition Limited, the power fold exterior mirror option is controlled by the DSM. Before running a self-test or retrieving codes, the power fold switch must be inactive for at least 30 seconds.
This is a complex vehicle , electronics , control modules an serial data communication networks. You mite be better off taking it to the dealer or some other repair shop . There could be DTC'S - diagnostic trouble codes stored in the SJB - body control module !
B1667 Mirror Driver Up/Down Motor Stalled Go To Pinpoint Test D . B1668 Mirror Driver Right/Left Motor Stalled Go To Pinpoint Test D . B1669 Mirror Passenger Up/Down Motor Stalled Go To Pinpoint Test D . B1670 Mirror Passenger Right/Left Motor Stalled Go To Pinpoint Test D . B1735 Mirror Driver Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1739 Mirror Driver Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B1743 Mirror Passenger Vertical Switch Circuit Short to Battery Go To Pinpoint Test D . B1747 Mirror Passenger Horizontal Switch Circuit Short to Battery Go To Pinpoint Test D . B2312 Mirror Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2314 Mirror Passenger Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2316 Mirror Passenger Vertical Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2318 Mirror Passenger Vertical Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . B2320 Mirror Driver Horizontal Feedback Potentiometer Circuit Failure Go To Pinpoint Test D . B2322 Mirror Driver Horizontal Feedback Potentiometer Circuit Short to Battery Go To Pinpoint Test D . Normal Operation During normal operation, when the front wiper wash is selected, the windshield wiper motor provides power to the washer pump through circuit CRW14 (BU/WH) and ground is provided to the washer pump through circuit CRW12 (GY/OG) and the rear wiper motor. If rear wiper wash is selected, the rear wiper motor provides power to the washer pump through circuit CRW12 (GY/OG) and ground is provided to the washer pump through circuit CRW14 (BU/WH) and the windshield wiper motor.
    Possible Causes
  • Multi-function switch
  • Open in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN), CRW20 (GY/YE), SBB49 (RD) or GD149 (BK/GY)
  • Short to ground in circuit CRW14 (BU/WH), CRW12 (GY/OG), CRW07 (GY/BN) or CRW20 (GY/YE)
  • Washer pump
  • Windshield wiper motor
  • Rear wiper motor
    This is

Feb 02, 2016 | 2010 Ford Expedition

1 Answer

How hard is it to re place the windshield washer tank on a 99 Olds mobile silouhett


Oldsmobile Silhouette Windshield Washer Reservoir ' Used ...

www.partshotlines.com > All Makes > Oldsmobile > Silhouette
Find a quality Oldsmobile Silhouette Windshield Washer Reservoir and other used Mini Van parts ... For example: If you're looking for a Hood Latch, ... This part is also known as Oldsmobile Silhouette Wdsh Washer Reserv; ... 1999 MONTANA

How To Install Replace Windshield Washer Pump Many GM ...

? 2:34
https://www.youtube.com/watch?v=jCqbhK_-hjY
Jun 7, 2010 - Uploaded by 1A Auto Parts
How To Install Replace Windshield Washer Pump Many GM Vehicles ... can u tell Me were the Fuse located ...

Oct 29, 2015 | Cars & Trucks

1 Answer

Windshield washer fluid lamp will not shut off. It is full. States that i need to add windshield washer fluid and it is full, how do you reset the sensor. ?


sometimes that takes a few starts and stops, if it doesn't clear in a couple of days unhook the battery wait 5 minutes and hook it back up

Jul 11, 2011 | 2008 GMC Sierra 1500

1 Answer

2002 Honda Odyssey van, the windshield washer doesn't squirt fluid or wipe the wipers, though the windshield wipers work separately . . . . how to fix?


Sounds like you may need to change the washer fluid pump. They do go bad. It's located inside the washer fluid reservoir, which is in the front of the passenger's side wheel well, behind the front bumper.

Mar 31, 2011 | 2002 Honda Odyssey

3 Answers

I think my van has a clogged windshield nozzle. The wiper fluid comes out but doesn't even squirt high enough to hit the windshield.


First try to clean out the squirter nozzles.Take a very small wire, sometimes a staple works great, and stick it into the nozzle to clear any debris.Then try to spray it again.If this didn't solve the problem and the debris is cleared, then you either have a weak or blocked pump, which is located on the washer reservoir itself.Hope I could help!!! Rate me accordingly!! Thanks!

Oct 06, 2010 | 2002 Chrysler Town & Country

1 Answer

1998 Toyota Starlet - Windshield Washer not working......ideas?


the washer motor is gone then ,,,its in the bottle,,

May 08, 2009 | 1983 Toyota Starlet

1 Answer

Trouble light


your windshield washer fluid is low..... nothing wrong.. just refill the windshield washer resovoir under the hood... usually the cap on it will look like the indicator you described.

Jan 12, 2009 | 2003 Chrysler Town & Country

Not finding what you are looking for?
2005 Dodge Caravan Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

83036 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...