Question about 2006 Hyundai Tucson

1 Answer

Headlight aiming how do i aim my hyundai tucson headlights? i just replaced a bulb in the front right light and need to re-aim it. help?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

On each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get rid of the dark spot in front of the car when the headlight is turned on? Is there any adjustment for this?


Headlights can be aimed, and after a bulb replacement they need to be. You can aim them, all it takes is night and a screwdriver. Rule of thumb:
Single headlights on each side, should be aimed to drop straight ahead and drop 2 feet per 100 feet. Dual headlights on each side, drop 1 foot per 100 feet.
It helps to have a level, 100 foot driveway or quiet street to aim. . .

Sep 12, 2014 | Cars & Trucks

1 Answer

Headlight & sidelight bulbs


Yes the lights are seperately fused.

Feb 11, 2014 | 2006 Hyundai Tucson

2 Answers

Replace bulb headlight


Most of the headlights do not unbolt to change bulbs. If it's a blown bulb you're trying to replace, look on the back side of the headlight housing. There should be a plug with wires attached going into the back. This plug should twist either to the right,left or up or down. Once you've twisted this plug out of the headlight housing you'll see the bulb you need to replace. Unplug the wire harness from the blown bulb and place it into the new bulb, being careful not to touch the new bulb with your bare hands as any oil or other contamination will cause these bulbs to blow as soon as they are turned on. Place the new bulb with harness back into the socket in headlight housing and twist into position.

Oct 19, 2013 | 2001 Hyundai Accent

1 Answer

Hi, I have a 2006 Hyundai Tucson. I love my Tucson except for one thing, it keeps blowing headlights. I have never had this issue with any other vehicle. I see that it seems to be a common issue with...


Have your voltage checked. This is usually done with an alternator test at a local autoparts store. If that checks out look closely at the mounts for the headlight and make sure its not loose. Vibration can cause bulbs to blow. Make sure there is no moisture in the lens. Water will cause it to blow.. Lastly when you replace the bulb do not touch the glass. The oil from your skin will cause it to blow early.

May 20, 2011 | Hyundai Tucson Cars & Trucks

1 Answer

How do I replace the front left (driver side) headlight? I have removed the cap and the electrical, but can't figure out how to remove the bulb so I can put a new one in. Your help is appreciated.


Removal & Installation
  1. Disconnect the negative battery terminal.

  2. Remove the head lamp mounting bolts, then disconnect the lamp connectors.

  3. Replace the head lamp bulb(A), position bulb(B) and turn signal bulbs(C).
    41311_tucs_g0048.gif

    Head lamp bulb(A), position bulb(B) and turn signal bulbs(C)

  4. To install, reverse removal procedure.

Dec 12, 2010 | 2005 Hyundai Tucson

1 Answer

Instructions on how to replace drivers side


Open hood, reach behind headlight. If necessary remove battery and coolant overflow tank.
Then reach in behind headlight. There will be a plastic ring on back of headlight. Turn counter clockwise and pull back and slide back out of the way. Then grab the headlight bulb, turn counter-clockwise and pull back to remove. Then unclip the wire harness from the bulb itself and reverse procedure to replace.

Nov 28, 2009 | 2005 Hyundai Tucson

2 Answers

How are the headlight adjusted for aim


there is one screw on top and one on the side of each light for adjustments

Nov 13, 2009 | 2001 Ford Escort ZX2

1 Answer

How do i change right headlight bulb on a 2007 hyundai tucson


You change it like you'd change any headlamp bulb. There is an access cap behind the headlamp assembly -- remove it, then remove the connector to the bulb, then remove the retaining clip/spring holding the bulb in place. Then install/insert the new bulb in the same 'ORIENTATION' as the old one. Reinstall in reverse order... ALAKAZAM!... .done!

Jun 24, 2009 | Hyundai Tucson Cars & Trucks

1 Answer

Fog Lamp Bulb Replacement, 05 Tucson


remove headlamp assembly and you can get it from the top pretty easy

Feb 25, 2009 | 2006 Hyundai Tucson

3 Answers

Side light bulb change on hyundai terracan


hi there
the solution is simple,
you only need to undo the screw on top of the side light/indicator. then facing the head light place a flat headed screw driver under the bottom lip of side light. the bottom of the lihgt is on a small push fit stud, use a sponge or cloth to protect your bumper paint work then just apply pressure gently to lever side light out towards you, It will come dont worry, you may then change your bulbs if you wish remove the whole light unit you will see the bottom bolt as soon as you release the side light. to replace just push back into place then replace screw. whole job takes about five minutes

hope this helps kevan hildred

Nov 23, 2008 | 2003 Hyundai Tucson

Not finding what you are looking for?
2006 Hyundai Tucson Logo

1,465 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...